1. Bubuka
This manual provides comprehensive instructions for the proper installation, maintenance, and troubleshooting of SCULPFUN replacement laser lenses. These official original lenses are designed to perfectly fit your SCULPFUN S30 series laser engraver, ensuring optimal performance and extending the service life of your laser module.
The package includes 6 replacement lenses and 6 sealing rings, providing a sufficient reserve for long-term use.
Image 1.1: SCULPFUN Laser Lens Kit, including lens holder, clear lens, and multiple replacement lenses and sealing rings.
2. Kasaluyuan produk
Ensure you select the correct lens type for your specific SCULPFUN laser module:
- White Lenses: Compatible with SCULPFUN S30 and S30 Pro 11W machines.
- Yellow Lenses: Compatible with SCULPFUN S30 Pro Max 22W and S30 Ultra 33W machines.
Image 2.1: White lenses and sealing rings for S30/S30 Pro 11W laser modules.
Image 2.2: Yellow lenses and sealing rings for S30 Pro Max/Ultra 22W/33W laser modules.
3. Pitunjuk Instalasi
Follow these steps carefully to replace the laser lens in your SCULPFUN S30 series laser engraver. Refer to Image 3.1 for a visual guide.
- Disassemble Set Screws: Carefully loosen and remove the set screws holding the gas nozzle in place.
- Twist Gas Nozzle: Gently twist the gas nozzle vertically to detach it from the laser module.
- Disassemble Lenses: Use a pair of tweezers to push the small pit and carefully remove the old lens.
- Clean Lens (if reusing) or Prepare New Lens: If reusing, use alcohol to clean the lens. If the lens is damaged, replace it with a new one from the kit.
- Pasang Lensa Anyar: Place the new lens into the designated slot. Ensure it is seated correctly.
- Tighten with Tweezers: Use tweezers to gently tighten the lens in place.
- Check Seal Ring Level: Verify that the sealing ring is properly seated and level to ensure an airtight seal.
- Re-attach Gas Nozzle: Twist the gas nozzle vertically back into position. Do not overtighten; feel for when it touches the bending tube facing right.
- Tighten Set Screws: Secure the gas nozzle by tightening the set screws.
Image 3.1: Visual guide for the 9-step laser lens replacement process.
Gambar 3.2: Detil view of the laser lens and gas nozzle assembly.
4. Pertimbangan Operasi
These replacement lenses are engineered from high-transparent material, minimizing laser energy loss and ensuring your laser engraver maintains its high power output and precision during operation. Proper installation is key to achieving optimal performance.
Image 4.1: Diagram illustrating the ultra-high transmittance of the lens, reducing laser energy loss.
Image 4.2: SCULPFUN laser module highlighting the super long service life provided by quality lenses.
5. Pangropéa
Regular maintenance of your laser lens is essential for consistent engraving quality and longevity.
- beberesih: The lens surface is reinforced to be anti-oil and anti-smoke. If the lens becomes dirty, gently wipe it with a lint-free cloth moistened with alcohol. Avoid abrasive materials that could scratch the surface.
- Pamariksaan: Periodically inspect the lens for any signs of damage, scratches, or excessive residue buildup that cannot be cleaned.
- ngagantian: If the lens is damaged or its clarity is compromised, replace it immediately using the installation steps provided in Section 3.
Image 5.1: Close-up of a lens with a reinforced surface, designed to be smoke and oil proof.
6. Cara ngungkulan
If you experience issues with your laser engraver after replacing the lens, consider the following:
- Reduced Laser Power/Quality:
- Incorrect Lens: Ensure you have installed the correct lens type (white for 11W, yellow for 22W/33W) for your laser module.
- Pamasangan anu teu leres: Recheck all installation steps, especially the seating of the lens and the level of the sealing ring. A loose or misaligned lens can significantly affect performance.
- Lénsa Kotor: Even new lenses can attract dust. Clean the lens with alcohol and a lint-free cloth.
- Gas bocor: If you notice air escaping around the nozzle, the sealing ring might be improperly seated or damaged. Replace the sealing ring if necessary and ensure it is level during reassembly.
- Ruksakna Fisik: If the lens appears scratched or cracked, it must be replaced. Even minor damage can scatter the laser beam and reduce effectiveness.
7. Spésifikasi
| Fitur | Rincian |
|---|---|
| Ngaran produk | SCULPFUN Laser Lens |
| Kasaluyuan | SCULPFUN S30, S30 Pro, S30 Pro Max, S30 Ultra Laser Engravers |
| Lens Type (11W) | White Lens (for S30/S30 Pro 11W) |
| Lens Type (22W/33W) | Yellow Lens (for S30 Pro Max 22W/S30 Ultra 33W) |
| Jumlah per Paket | 6 Lenses, 6 Sealing Rings |
| Bahan | High-transparent material with reinforced, anti-oil and anti-smoke surface |
| Ukuran Paket | 25 x 105 x 52 mm (9.8 x 4.1 x 2 inci) |
| Beurat pakét | 0.1 kg (3.5 oz) |
Image 7.1: Contents of the lens replacement kit: 6 lenses and 6 sealing rings.
8. Garansi jeung Rojongan
These are official original SCULPFUN replacement parts. For any issues or questions regarding the product, please contact the SCULPFUN Factory Store directly. They are committed to providing support and assistance.
9. Tips pamaké
- Nanganan kalayan ati-ati: Always handle the lenses by their edges to avoid fingerprints or scratches on the optical surface.
- Kabersihan teh konci utama: A clean lens is crucial for optimal laser performance. Even minor dust or smudges can significantly reduce engraving quality.
- Cék biasa: Make it a habit to visually inspect your laser lens before each major engraving project.
- Keep Spares Handy: Having a reserve of lenses ensures minimal downtime if a lens gets damaged or excessively dirty.
