Skydance Wall Touch Panel 2.4G RF 4-Zone LED Controller

Bubuka

This manual provides comprehensive instructions for the installation, setup, operation, and maintenance of your Skydance TW1-4, TW2-4, TW4-4, and TW5-4 Wall Touch Panel 2.4G RF 4-Zone LED Controllers. These controllers are designed for various LED strip types, including single color, dual color (WW/CW), RGB, RGBW, and RGBCCT, offering intuitive control through a sensitive glass touch panel.

Émbaran Kasalametan

1. Baca sagala parentah taliti saencan Anjeun ngamimitian pamasangan ieu.
2. When installing the battery, pay attention to the battery's positive and negative polarity.
3. For long periods without using the remote control, remove the battery.
4. If the remote distance becomes smaller or the panel becomes insensitive, replace the battery.
5. Cabut jeung geura daur ulang atawa buang accu dipaké nurutkeun peraturan lokal sarta jauh ti barudak.
6. Entong miceun batré kana sampah rumah tangga atanapi dibakar.
7. Do not force discharge, recharge, disassemble, or heat the battery.
8. Stop using the product if the battery compartment is not securely closed.
9. If swallowing occurs, seek medical attention immediately.
10. Gently handle the remote; beware of falling.
11. Pikeun lokasi jero ruangan sareng garing ngan ukur dianggo.

Produk Leuwihview

Models and Applicable Lights

The Skydance Wall Touch Panel series includes the following models, each designed for specific LED strip types:

• TW1-4: 4-Zone Dimming Controller for Single Color LED Strips.
• TW2-4: 4-Zone CCT Controller for Dual Color (WW/CW) LED Strips.
• TW4-4: 4-Zone RGB/RGBW Controller for RGB and RGBW LED Strips.
• TW5-4: 4-Zone RGB+CCT Controller for RGBCCT LED Strips.

Fitur konci

• 1-5 color 4-zone RF remote control.
• Unggal panel touch tiasa kadali jauh sababaraha RF 2.4G LED Controllers.
• Ultra-sensitive high-strength glass touch panel with a central touch color wheel.
• Touch keys with LED indicators.
• CR2032 battery-powered, no wiring required, removable.
• Available in White & Black finishes.

Pamasangan

Struktur mékanis jeung Dimensi

The panel has dimensions of 86mm x 86mm on the front, with 60mm x 60mm mounting holes and a depth of 9.50mm.

Pamasangan batré

The controller is powered by a CR2032 battery. Before first use, remove any protective film from the battery. Open the battery cover with a screwdriver to insert or replace the battery, ensuring correct positive and negative polarity. If the LED indicator is on when a key is pressed but the panel is unresponsive, the battery may be dead and needs replacement.

Pilihan Pamasangan

To fix the panel to the wall, three options are available:

1. Pilihan 1: Ngalereskeun eta dina témbok jeung dua screws.
2. Pilihan 2: Stick it on the wall with 3M tape.
3. Pilihan 3: The panel can be adsorbed directly onto metal surfaces.

Setup: Matching with RF LED Controller

The touch panel needs to be matched with an RF 2.4G LED controller (receiver) to function. Two methods are available for matching or deleting a match:

Method 1: Using the Controller's Match Key

• Pertandingan: Short press the match key on the LED controller, then immediately press the 'on/all' key on the touch panel. The LED indicator will flash a few times, indicating a successful match.
• Pupus: Press and hold the match key on the LED controller for 5 seconds to delete all matched remotes. The LED indicator will flash a few times, confirming all matched remotes were deleted.

Métode 2: Ngagunakeun Power Restart

• Pertandingan: Switch off the power to the LED controller, then switch it on. Immediately short press the 'on/off' key on the touch panel 3 times. The light blinks 3 times, indicating a successful match.
• Pupus: Switch off the power to the LED controller, then switch it on. Immediately short press the 'on/off' key on the touch panel 5 times. The light blinks 5 times, confirming all matched remotes were deleted.

Operasi

Each panel model offers specific control functionalities:

General Controls (All Models)

• Tombol Daya: Turns on/off all connected lights.
• Zone Buttons (1, 2, 3, 4): Short press to turn on a specific zone and select it. Long press for 2 seconds to turn off a zone. Quickly pressing multiple zone keys will select multiple zones synchronously. Each zone can control multiple receivers.

TW1-4 (4 Zone Dimming Panel)

• Brightness Icon: Adjusts brightness (10 levels).
• Roda Warna: Toél pikeun ngarobah kacaangan.
• Scene 1/2 Buttons: Short press to recall a saved scene. Long press for 5 seconds to save the current state to Scene 1 or 2.

TW2-4 (4 Zone CCT Panel)

• Brightness Icon: Adjusts brightness (10 levels).
• Color Temperature Icon: Toél pikeun ngarobah suhu warna.
• Scene 1/2 Buttons: Short press to recall a saved scene. Long press for 5 seconds to save the current state to Scene 1 or 2.

TW4-4 (4 Zone RGB/RGBW Panel)

• Brightness Icon: Adjusts brightness (10 levels).
• Tombol Mode: Short press to cycle through the next dynamic mode. Long press for 2 seconds to run mode/cycle.
• Tombol Speed: In dynamic mode, adjusts speed (10 levels). Long press for 2 seconds to reset to default speed. For static RGB color, adjusts saturation (11 levels). Long press for 1-6 seconds for continuous adjustment.
• Roda Warna: For RGB light, short press to get white (RGB mix). For RGBW light, short press to get white (W channel). Long press for 1-6 seconds to adjust W brightness. Touch to change static RGB color.

TW5-4 (4 Zone RGB+CCT Panel)

• Brightness Icon: Adjusts brightness (10 levels).
• Tombol Mode: Short press to cycle through the next dynamic mode. Long press for 2 seconds to run mode/cycle.
• Tombol Speed: In dynamic mode, adjusts speed (10 levels). Long press for 2 seconds to reset to default speed. For static RGB color, adjusts saturation (11 levels). Long press for 1-6 seconds for continuous adjustment.
• Color Temperature Icon: Adjusts color temperature (11 levels).
• Roda Warna: Toél pikeun ngarobah warna RGB statik.

Advanced Settings: Zone Light Type Configuration

Each zone can be configured to match single color, dual color (WW/CW), RGB/RGBW, or RGB+CCT controller types.

Changing a Single Zone's Light Type

Long press any of the Zone keys (1, 2, 3, or 4) and any of the four function keys (Brightness, Color Temp, Mode, Speed) for 2 seconds. This will change the light type for that specific zone.

Changing All Four Zones' Light Type Simultaneously

Long press the 'ALL' key and any of the four function keys for 2 seconds. This will change the light type for all four zones at the same time.

Specific Light Type Combinations

• Zone(s) + Brightness Icon: Long press for 2 seconds to set 1, 2, 3, or 4 zones as single color type.
• Zone(s) + Color Temperature Icon: Long press for 2 seconds to set 1, 2, 3, or 4 zones as dual color type.
• Zone(s) + Color Wheel Icon: Long press for 2 seconds to set 1, 2, 3, or 4 zones as RGB/RGBW color type.
• Zone(s) + Mode Icon: Long press for 2 seconds to set 1, 2, 3, or 4 zones as RGB+CCT type.

Changing All Zones to a Specific Light Type

• ALL + Brightness Icon: Long press for 2 seconds to set all 4 zones as single color type.
• ALL + Color Temperature Icon: Long press for 2 seconds to set all 4 zones as dual color type.
• ALL + Color Wheel Icon: Long press for 2 seconds to set all 4 zones as RGB/RGBW color type.
• ALL + Mode Icon: Long press for 2 seconds to set all 4 zones as RGB+CCT type.

Example: To change Zone 1's light type to RGB, long press Zone 1 and the Color Wheel icon for 2 seconds. When the setting is complete, the LED indicator will light up red and blue.

Scene Locking/Unlocking (TW1-4 and TW2-4)

The scene keys on TW1-4 and TW2-4 panels can be set to a locked state to prevent accidental saving of scenes. By default, the scene function is not locked.

To Lock Scene Keys

1. Short press the panel's 'on/off' key.
2. Turn on the light first, then turn off the light.
3. Immediately long press the panel's 'on/off' key for 5 seconds.
4. Then, immediately long press any one scene key (Scene 1 or Scene 2) for 5 seconds. All scene keys will now be in a locked state.

To Unlock Scene Keys

1. Short press the panel's 'on/off' key.
2. Turn on the light first, then turn off the light.
3. Immediately long press the panel's 'on/off' key for 5 seconds.
4. Then, immediately long press any one scene key (Scene 1 or Scene 2) for 10 seconds. All scene keys will now be in an unlocked state.

Tip pamaké

• Sababaraha Controllers: Each touch panel can control multiple RF 2.4G LED controllers. If you wish to control more LED strips or different sets of strips, you can match multiple wall panels to the same receivers for synchronized control, or to different receivers for independent control.
• Kahirupan batré: To maximize battery life, remove the CR2032 battery if the remote control will not be used for an extended period.
• Responsive Control: If you notice a decrease in remote distance or responsiveness, it's likely time to replace the CR2032 battery.

Pamérésan masalah

• Panel Unresponsive / LED Indicator On: If the LED indicator lights up when a key is pressed but the panel does not control the lights, the CR2032 battery may be dead. Replace the battery, ensuring correct polarity.
• Reduced Remote Distance: If the effective remote control distance decreases, replace the CR2032 battery.
• Matching Issues: Ensure the LED controller (receiver) is powered on and within the 30m barrier-free remote distance during the matching process. Try both matching methods if one fails.
• Battery Compartment Not Secure: If the battery compartment cannot be securely closed, stop using the product and contact support.

Pangropéa

• beberesih: Wipe the glass touch panel with a soft, dry cloth. Avoid using abrasive cleaners or solvents.
• Ngagantian batré: Replace the CR2032 battery as needed, following the safety guidelines.
• Panyimpenan: Store the panel in a dry, indoor location away from extreme temperatures and direct sunlight.

spésifikasi

Garansi sareng Rojongan

This product comes with a 3-year warranty. For technical support, troubleshooting assistance, or warranty claims, please contact your retailer or the manufacturer directly. Ensure you have your purchase details and product model information available.

Eusi pakét

pakét anjeun kedah ngandung:

• 1x Skydance Wall Touch Panel Remote (Type as selected: TW1-4, TW2-4, TW4-4, or TW5-4)
• Catetan: The CR2032 battery is NOT included and must be purchased separately.