1. Bubuka
This manual provides detailed instructions for the Ditec GOL4 series rolling code remote control, compatible with various Ditec garage door and gate systems. Please read this manual carefully before use to ensure proper setup and operation.
2. Spésifikasi
| Fitur | Rincian |
|---|---|
| Modél produk | DITEC GOL4 (SMG-240-DITEC) |
| Métode Encoding | Kodeu Rolling |
| Frékuénsi | 433.92 MHz |
| Jumlah Kancing | 4 |
| Batré | 3V (CR2032 included) |
| Radio Transmission Distance | 20-100m (Open area) |
| Diménsi | 60mm (L) x 37mm (W) x 5mm (H) |
| Beurat produk | 40 g |
| Bahan Produk | ABS |
| Sertifikasi | CE |
| Asalna | Daratan Cina |
3. Eusi Paket
- 1 x Ditec GOL4 Remote Control
- 1 x Manual Pamaké Inggris
- 1 x Batré CR2032 (parantos dipasang)
- 1 x Gantungan Kunci
4. Kasaluyuan
This remote control is compatible with the following Ditec rolling code models:
- DITEC GOL4
- DITEC BIXLG4
- DITEC BIXLP2
- DITEC BIXLS2
Catetan penting:
- This remote control is NOT compatible with DITEC GOL4C Fixed code remotes.
- Always verify the LED light color of your existing remote or receiver to confirm it is a rolling code system, as GOL4 (rolling code) typically has a different LED color than GOL4C (fixed code).
5. Setup (Programming a New Remote)
Follow these steps to program your new Ditec GOL4 remote control:
- Locate the Receiver: Open the control box of your garage door or gate system and locate the receiver board. Ensure that jumper JR6 on the receiver board is in the 'on' position.
- Lebetkeun Mode Programming: Press and hold the black PRG button on the receiver board for approximately 5 seconds.
- Programkeun Remote: While the receiver is in programming mode, press and hold the desired button on your new remote control for 5 seconds.
- Finalize Programming: Release the button on the remote. Wait for approximately 10 seconds for the receiver to reset and complete the programming process.
- Tes: Test the new remote control to ensure it operates your system correctly.
6. Parentah Operasi
Once programmed, operating your Ditec GOL4 remote control is straightforward:
- Press any of the four buttons on the remote control to activate your garage door, gate, alarm, automatic door, or roller shutter, depending on the system it is paired with.
- Ensure you are within the radio transmission distance of 20-100 meters (in an open area) for optimal performance.
7. Pangropéa
Ngagantian batré
The remote control is powered by a 3V CR2032 button cell battery. If you notice a decrease in the remote's operating range or if it stops responding, the battery may need replacement.
- Buka remot kontrol kalayan ati-atiasing.
- Leupaskeun batré CR2032 heubeul.
- Pasangkeun batré CR2032 anyar, pastikeun polaritasna bener (sisi + ka luhur).
- Close the remote control casing aman.
8. Cara ngungkulan
- Remote not responding after programming:
- Ensure the jumper JR6 on the receiver board was correctly set to 'on' during programming.
- Verify that the remote control is compatible with your Ditec system (e.g., not a fixed code GOL4C model). Check the LED color if unsure.
- Make sure the battery is correctly installed and has sufficient charge.
- Repeat the programming steps carefully.
- Rentang operasi anu dikirangan:
- Ganti batré CR2032.
- Pastikeun teu aya halangan anu signifikan antara remot sareng panarima.
- Check for sources of radio interference in the vicinity.
- Aktivasina teu kahaja:
- Ensure buttons are not being pressed inadvertently while carrying the remote. Consider using the included keychain to secure it.
9. Tips pamaké
- Always verify compatibility with your existing system before attempting to program a new remote. This remote is specifically designed for Ditec rolling code systems (GOL4, BIXLG4, BIXLP2, BIXLS2) and is not compatible with Ditec GOL4C fixed code remotes or other brands like VDS 4 premium.
- Keep your remote control away from extreme temperatures and moisture to prolong its lifespan.
10. Patarosan anu Sering Ditaroskeun (FAQ)
- Q: Is this remote compatible with VDS 4 premium controllers?
- A: No, this remote control is designed for Ditec rolling code systems (GOL4, BIXLG4, BIXLP2, BIXLS2) and is not compatible with VDS 4 premium controllers.
11. Garansi jeung Rojongan
For detailed information regarding warranty and support, please refer to the official user manual PDF available at link ieu. For further assistance, contact the manufacturer, Shenzhen Scimagic Development Technology Co.Ltd, at Honghai Gebu Building 2301, Baoan Road, Songgang Baoan District Shenzhen Guangdong China.
