Universal Garage Door Remote Control

1. Bubuka jeung Leuwihview

This Universal Garage Door Remote Control (Model AG037) is designed to clone and operate various garage door openers, electric doors, and switches. It supports a wide range of frequencies from 280MHz to 868MHz, including both fixed and rolling codes. With its advanced cloning capabilities, one remote can control up to four different devices or brands simultaneously, offering a convenient and versatile solution for your access control needs.

2. Important Pre-Purchase Notes

Please read carefully before attempting to use or purchase:

• This remote control is NOT 100% universal.
• It is NOT compatible with MyQ technology openers.
• It can ONLY copy the brands and models listed in the 'Copy Brand List' (refer to seller for this list).
• For specified brands, you may need to RE-GENERATE a new remote.
• Ensure your original garage door remote model is explicitly in the 'Copy Brand List' provided by the seller, otherwise, this device WILL NOT WORK.
• If you are unsure about compatibility, please contact the seller for verification before proceeding.

3. Spésifikasi

4. Fitur

• Multi-Frequency Support: Operates across a broad spectrum of frequencies (280-868MHz) to ensure wide compatibility.
• Universal Cloning: Capable of cloning up to four different original remote controls, even from different brands or with different frequencies, into a single new remote.
• Code Versatility: Supports cloning of Rolling Code, Fixed Code, and Learning Code types.
• Easy Face-to-Face Copy: Designed for simple, direct cloning from an original remote.
• Automatic Frequency Scanning: Features auto-scan for multi-frequency detection.
• Desain awét: Constructed from ABS and Metal for enhanced durability.
• Konsumsi Daya Lemah: Equipped with a CR2032 battery that typically lasts for one year.
• Portabel: Compact design with an integrated keychain for easy carrying.

5. Setup and Programming Instructions

The cloning process involves two main steps: copying the frequency from your original remote to the new remote, and then, for rolling codes, programming the new remote to your receiver/motor.

Step 1: Clear Existing Code (If Any)

1. Press and hold buttons A and B simultaneously on the new remote until the LED flashes rapidly (usually 3 times).
2. While still holding button A, release button B, then press button B three times. The LED should flash rapidly, indicating the code has been cleared.
3. Release all buttons. The remote is now ready for cloning.

Step 2: Copy Frequency from Original Remote

1. Place the original remote and the new remote side-by-side, as close as possible.
2. Press and hold the desired button on your original remote (e.g., the button that opens your garage door).
3. Simultaneously, press and hold the corresponding button on the new remote (e.g., button A).
4. Hold both buttons until the LED on the new remote flashes rapidly (usually 3 times, then continuously). This indicates successful cloning of the frequency.
5. Repeat this process for any other buttons (B, C, D) you wish to program from your original remote(s).

Step 3: Program to Receiver (For Rolling Codes Only)

If your original remote uses a rolling code, you must also program the new remote directly to your garage door opener's receiver. Fixed code remotes typically only require Step 2.

1. Locate the 'Learn' or 'Program' button on your garage door opener's motor unit. This button is usually found on the back or side of the motor.
2. Press and release the 'Learn' or 'Program' button. The indicator light on the motor will usually illuminate or flash, indicating it's in programming mode.
3. Within 30 seconds, press the desired button on your newly cloned remote (e.g., button A) once.
4. The motor's indicator light may flash or turn off, confirming successful programming.
5. Test the new remote to ensure it operates the garage door correctly.

6. Parentah Operasi

Once successfully programmed, operating your garage door or other devices with the new remote is straightforward:

• Simply press the corresponding button (A, B, C, or D) on the remote that you have programmed for a specific function.
• The red LED indicator on the remote will light up when a button is pressed, confirming signal transmission.
• Ensure you are within range of the receiver for proper operation.

7. Pangropéa

Ngagantian batré

The remote control uses one CR2032 3V button cell battery. The battery is included and typically lasts for about one year under normal use.

1. Locate the battery compartment on the remote control. This is usually a small slot or cover on the side or back.
2. Carefully open the compartment using a small screwdriver or coin.
3. Leupaskeun batré CR2032 heubeul.
4. Insert a new CR2032 battery, ensuring the positive (+) side is facing up.
5. Tutup kompartemen batré anu aman.

beberesih

To clean the remote control, wipe it with a soft, dry cloth. Do not use harsh chemicals or abrasive cleaners, as these may damage the casing atawa komponén internal.

8. Cara ngungkulan

• Remote not working after cloning:
  • Verify that your original remote's brand and model are on the seller's 'Copy Brand List'.
  • Ensure the cloning process (Step 2) was performed correctly, with the remotes in close proximity.
  • For rolling code systems, confirm that Step 3 (programming to the receiver) was completed successfully.
  • Check the battery in the new remote; replace if necessary.
• rentang operasi pondok:
  • Ganti batré CR2032 dina jarak jauh.
  • Ensure there are no significant obstructions (e.g., thick walls, metal objects) between the remote and the receiver.
  • Check for potential radio frequency interference from other electronic devices in the vicinity.
• LED does not light up when pressing a button:
  • The battery may be dead or incorrectly inserted. Replace or re-insert the battery.

9. Tips pamaké

• Always test the newly cloned remote thoroughly in various conditions before relying on it for daily use.
• Keep your original remote control in a safe place as a backup and for future cloning needs.
• If you are cloning multiple remotes for different devices, consider labeling the buttons on the new remote for easy identification.
• When cloning, ensure minimal interference from other electronic devices to achieve the best signal copy.

10. Garansi jeung Rojongan

This product comes with a 1-year warranty from the date of purchase. For any questions, technical support, or warranty claims, please contact the seller directly through your purchase platform. Ensure you have your order details available when contacting support.