1. Bubuka
This manual provides essential information for the proper installation, programming, operation, and maintenance of your Scimagic-RC remote control, compatible with TELECO TXP-433-A01, TXP-433-A02, and TXP-433-A04 gate and garage door systems. Please read these instructions carefully before use to ensure optimal performance and longevity of your device.
2. Spésifikasi
| Fitur | Spésifikasi |
|---|---|
| Bahan Produk | ABS |
| Beurat produk | 50 g |
| Jumlah Saluran | 1, 2, or 4 (depending on model) |
| Batré | 3V CR2032 (kaasup) |
| Pamasangan | Nirkabel |
| Métode Encoding | Kodeu Rolling |
| Frékuénsi | 433 MHz, 433.92 MHz |
| Radio Transmission Distance | 20-100m (Open area) |
| Nomer modél | TELECO TXP-433-A01, TELECO TXP-433-A02, TELECO TXP-433-A04 |
2.1. Diménsi
3. Eusi Paket
Paket anjeun kedah kalebet barang-barang ieu:
- Kadali jauh
- Batré CR2032 (tos dipasang atanapi misah)
- Gantungan konci
- Klip
- Manual Inggris
4. Kasaluyuan
This remote control is 100% compatible with the following TELECO models:
- TELECO TXP-433-A01
- TELECO TXP-433-A02
- TELECO TXP-433-A04
4.1. Important Incompatibility Note
This remote control is NOT compatible with TELECO TVTXP 868MHz models with a grey shell.
5. Setelan & Pamrograman
To program your new replacement remote control, you must have access to your gate or garage door motor (receiver). If you do not have access to the motor, this remote control cannot be programmed.
5.1. Programming Steps
- Aksés Motor: Locate and press the programming button (often labeled 'Learn' or 'Prog') on your gate or garage door motor (receiver). The LED indicator on the motor will illuminate.
- Press Remote Button: Within a few seconds, press the desired button on your new remote control that you wish to program.
- Konfirmasi: The opener light on your motor will flash, confirming successful programming. The remote control button is now paired and will operate the opener.
5.2. Erasing All Codes from Receiver
To erase all previously learned codes from your motor's receiver, follow these steps:
- Hold Learn Button: Press and hold the 'Learn' button on the receiver.
- Wait for LED: Continue holding the button until the indicator light on the receiver turns off (this usually takes about 30 seconds).
- Konfirmasi: All codes that the receiver has learned will be erased. You will then need to reprogram any desired remote controls.
6. Operasi
Once programmed, simply press the corresponding button on your remote control to activate your gate or garage door opener. The remote control features an indicator light to confirm button presses.
6.1. Wall Mount Base
The remote control comes with a convenient wall mount base. This allows you to fix the base to a wall near your entry point, providing easy access to the remote while keeping it secure.
To remove the remote control from the base, simply slide it upwards as shown in the illustration.
6.2. Video Demonstrasi Produk
Video 1: A demonstration of the remote control's features and how it interacts with its wall mount base.
7. Pangropéa
7.1. Ngagantian batré
The remote control uses a CR2032 3V battery. When the remote's range decreases or the indicator light dims, it's time to replace the battery.
- Buka Casing: Buka remot kontrol lalaunanasing.
- Cabut Batré heubeul: Cabut batré CR2032 anu lami kalayan ati-ati.
- Selapkeun Batré Anyar: Insert a new CR2032 battery, ensuring the positive (+) side is facing up.
- Tutup Casing: Snap the casing ngahiji deui kalawan aman.
8. Cara ngungkulan
- Jauh teu tiasa dianggo saatos program: Ensure the programming steps were followed correctly. The motor's LED should flash to confirm successful pairing. If not, repeat the programming process.
- Reduced range or intermittent operation: This often indicates a low battery. Replace the CR2032 battery as described in the Maintenance section.
- Remote not responding at all: Check the battery. If the battery is new and correctly installed, try reprogramming the remote. Ensure there are no strong radio interference sources nearby.
- Masalah incompatibility: Double-check that your existing system is one of the compatible TELECO TXP-433-A models. This remote is not compatible with 868MHz systems.
9. Tips pamaké
- Always keep your remote control in a safe and easily accessible location, such as the provided wall mount base.
- Avoid exposing the remote control to extreme temperatures, moisture, or direct sunlight for extended periods.
- If you have multiple remotes, consider labeling them to avoid confusion, especially if they control different devices.
10. Jaminan & Dukungan
This product is a replacement remote control compatible with specific TELECO systems. It is not an original TELECO product. All brand names, trademarks, and registered trademarks mentioned are the property of their respective legal owners and are used solely for descriptive and identification purposes.
For any questions regarding compatibility, programming, or general inquiries, please contact the seller or manufacturer for assistance. Ensure you provide your product model number (TXP-433-A02) and details of your existing gate/garage door system for efficient support.
