1. Produk Langkungview
The SUNLU Standard Plus Resin is an advanced photopolymer resin designed for LCD 3D printers, offering enhanced precision, toughness, and faster curing times compared to standard resins. It is suitable for a wide range of 3D printing applications, from detailed models to functional parts.
2. Kasalametan jeung Penanganan
Always prioritize safety when handling photopolymer resins. Follow these guidelines:
- Maké Alat Pelindung: Always wear gloves and safety glasses to avoid direct skin and eye contact with the resin.
- Ventilasi: Use the resin in a well-ventilated area to minimize exposure to fumes.
- Hindarkeun Ingestion: Do not take orally. Keep away from children and pets.
- Kontak Kulit: Bisi katepaan kulit, geura cuci ku sabun sareng cai.
- Kontak panon: In case of eye contact, flush immediately with plenty of water and seek medical attention.
- Panyimpenan: Store the resin in a sealed container, away from direct sunlight and UV light sources, in a cool, dry place between 15-35°C (59-95°F). Avoid dust contamination.
- pembuangan: Dispose of cured resin and waste materials according to local regulations. Never pour liquid resin down the drain.
3. Setup jeung Persiapan
- Ngocok Botol: Before each use, shake the resin bottle thoroughly for at least 30 seconds to ensure all components are well mixed.
- Kasaluyuan printer: This resin is compatible with most 4K/8K/LCD/DLP/SLA 3D printers that use 395-405nm UV light for curing.
- Lingkungan: Ensure your printing environment is clean, well-ventilated, and maintained at an optimal ambient temperature of 25-30°C with relative humidity below 60%.
- Pouring Resin: Carefully pour the desired amount of resin into your printer's resin vat. Avoid overfilling.
4. Operating Instructions (Printing Parameters)
The following parameters are suggested starting points for printing with SUNLU Standard Plus Resin. Optimal settings may vary depending on your specific 3D printer model and environmental conditions. Always perform calibration prints to fine-tune your settings.
| Parameter | Monochrome LCD Screen | RGB LCD Screen | Catetan |
|---|---|---|---|
| Print optimum ambient temperature | 25-30°C / <60%RH | Maintain stable environment | |
| Recommended print layer thickness | 0.05 mm | Standard layer height | |
| Bottom layer number | 5-10 | Number of initial layers for bed adhesion | |
| Bottom exposure time (s) | 10-60s | 20-80s | Longer time for better adhesion |
| Normal layer exposure time (s) | 2-4s | 4-15s | Adjust based on detail and printer power |
| Lifting height (mm) | 6-10 mm | For 7-inch or larger machines: >8mm; for 10-inch or larger machines: >10mm | |
| Lifting speed (mm/min) | 60-120 | Speed at which the build plate lifts | |
| Return/descent speed (mm/min) | 120-180 | Speed at which the build plate descends | |
| Extinguishing delay time (s) | 0.5-1 | Time delay before next layer exposure | |
For large models, it is recommended to slightly increase the exposure time to ensure proper curing.
5. Post-Processing and Maintenance
- beberesih: After printing, carefully remove the model from the build plate. Clean the printed model using 95% or higher purity ethanol or isopropanol. Ultrasonic cleaning for 5-6 minutes is recommended. Brushing can enhance the cleaning effect.
- Pasca-curing: After cleaning, cure the model in a post-curing chamber for 3-5 minutes. This step enhances the mechanical properties and durability of the print.
- Resin Vat Maintenance: After printing, filter any uncured resin back into the bottle for future use. Clean the resin vat and build plate thoroughly with isopropyl alcohol.
6. Ngungkulan Masalah Umum
- Print Failure/Poor Adhesion:
- Ensure the build plate is level and clean.
- Increase bottom exposure time.
- Verify ambient temperature is within the recommended range (25-30°C).
- Shake the resin bottle thoroughly before use.
- Soft or Brittle Prints:
- Increase normal layer exposure time.
- Ensure adequate post-curing.
- Check resin shelf life.
- Excessive Odor:
- Ensure proper ventilation in your printing area.
- While SUNLU resin has minimal odor, individual sensitivity varies.
- Resin Leakage:
- Inspect the resin vat for damage or improper installation.
- Ensure the resin bottle cap is securely tightened after use.
If you encounter persistent issues, refer to your 3D printer's manual or contact SUNLU customer support for assistance.
7. Spésifikasi
7.1 General Properties
- Bahan: Photosensitive Resin
- Bentuk: Cairan
- Kasaluyuan: LCD 3D Printers (also compatible with 4K/8K/DLP/SLA)
- Curing Wavelength: 395-405nm UV Curing
- Kahirupan rak: 2 taun
7.2 Physical Properties
| Harta | Nilai | Unit |
|---|---|---|
| Kapadetan Cairan | 1.1000 ± 0.05 | g/cm³ |
| Kapadetan padet | 1.1800 ± 0.02 | g/cm³ |
| Resin Viscosity | 100-350 | mPa.s/°C |
7.3 Mechanical Properties (Standard Plus Resin)
| Harta | Nilai | Unit |
|---|---|---|
| Kakuatan regangan | 33 | MPa |
| Elongation di Break | 15 | % |
| Kakuatan Bending | 35 | MPa |
| Modulus lentur | 1225 | MPa |
| Beuki karasa | 80-84 | D |
| Nyusutan | 7-9 | % |
7.4 Packaging Dimensions
- Ukuran Botol: Kira-kira 210mm (Jangkungna) x 126mm (Lebar) x 53mm (Jerona)
- Ukuran Kotak Hadiah: 160mm x 83mm x 275mm
- Gross Weight/Box: 1.296 KG
- Outer Box Size: 435mm x 335mm x 295mm
8. Tips pamaké
- Ramah Pemula: This resin is well-suited for novice users and for printing intricate models and artifacts due to its ease of molding and improved precision.
- Percetakan Hemat Biaya: Benefit from a resin that offers a good balance of performance and cost-effectiveness.
- Rincian ditingkatkeun: Achieve prints with smoother surfaces, clearer textures, and more delicate details compared to standard resins.
- Low Shrinkage for Accuracy: The low volume shrinkage during curing contributes to exceptional precision and stable print performance.
- Minimal Odor: While 3D printing, the resin produces a light odor, balancing functionality with user comfort.
9. Garansi jeung Rojongan
SUNLU is committed to providing high-quality products and excellent customer service. For any questions, technical support, or issues not covered in this manual, please contact SUNLU customer support.
Manual pamaké lengkep dina format PDF sadia pikeun diundeur: View Manual Pamaké (PDF)
For further assistance, please visit the official SUNLU websitus atanapi ngahubungan pangecér Anjeun.
