DOOYA DC73A Wireless Receiver Instruction Manual

1. Produk Langkungview

The DOOYA DC73A is a wireless receiver designed to control standard 4-wire motors, typically used for applications such as roller shutters, blinds, or projection screens. It operates at 433MHz and is compatible with DOOYA brand remote controls. This receiver allows for convenient wireless operation of your motor.

Figure 1: DOOYA DC73A Wireless Receiver

Gambar 2: Internal view of the DC73A Receiver

2. Émbaran Kasalametan

• Pastikeun catu daya dipegatkeun samemeh dipasang atawa diropéa.
• Installation should be performed by a qualified electrician or technician.
• Ulah ngalaan panarima kana kalembaban atanapi suhu anu ekstrim.
• Verify correct wiring connections to prevent damage to the receiver or motor.

3. Instalasi jeung Wiring

The DC73A receiver is designed for integration with standard 4-wire motors. Refer to the wiring diagram below for proper connection.

Figure 3: DC73A Receiver Specification Sheet (Wiring and Setup)

3.1 Wiring Connections (Refer to Figure 3, 'Mode of connection')

Connect the receiver to your 4-wire motor and power supply as follows:

• Kawat beureum: Hirup (L)
• Kawat bodas: nétral (N)
• Kawat Hideung: Up (Motor Up command)
• Kawat coklat: Down (Motor Down command)
• Kawat Héjo/Konéng: Bumi (Taneuh)

Pastikeun sadaya sambungan aman sareng insulated.

3.2 Installation Distance (Refer to Figure 3, 'The best installation distance')

For optimal performance, observe the recommended installation distances:

• Outdoor Control Range: Up to 200 meters (unobstructed).
• Indoor Control Range: Up to 35 meters (through walls/obstacles).
• Avoid installing the receiver near large metal objects or other sources of electromagnetic interference.

4. Operasi sareng Pamasangan

The DC73A receiver is controlled by a compatible DOOYA remote control. Follow these steps to pair a remote control and set motor limits or functions.

4.1 Setting Up (Pairing a Remote - Refer to Figure 3, 'Setting up')

1. Pareum listrik: Pegatkeun sambungan kakuatan ka panarima.
2. Daya Hurung: Sambungkeun deui kakuatan ka panarima.
3. Press P2 Button: On your remote control, press the P2 button once. The motor should run for 1 second.
4. Press P2 Again: Press the P2 button on the remote control again. The motor should run for 1 second.
5. Press P2 Three Times: Press the P2 button on the remote control three times. The motor should run for 10 seconds.
6. Press P2 Seven Times: Press the P2 button on the remote control seven times. The motor will continuously work (this may be a factory reset or continuous run mode).
7. Konfirmasi: Press the 'OK' button on the remote to confirm the setting.

4.2 Adding an Emitter (Remote Control - Refer to Figure 3, 'Add Emitter')

To add another remote control (emitter) to the receiver:

1. Pareum listrik: Pegatkeun sambungan kakuatan ka panarima.
2. Daya Hurung: Sambungkeun deui kakuatan ka panarima.
3. Press P2 on Existing Remote: Press the P2 button on an already paired remote control once. The motor should run for 1 second.
4. Press P2 on New Remote: Press the P2 button on the new remote control you wish to pair. The motor should run for 1 second.
5. Konfirmasi: Press the 'OK' button on the new remote to confirm pairing.

4.3 Light Adjust Function (Refer to Figure 3, 'Light adjust function')

This function may be used for adjusting motor limits or specific light settings if applicable to your motor system.

1. Pareum listrik: Pegatkeun sambungan kakuatan ka panarima.
2. Daya Hurung: Sambungkeun deui kakuatan ka panarima.
3. Press P2 Button: Press the P2 button on the remote control once. The motor should run for 1 second.
4. Press P2 Three Times: Press the P2 button on the remote control three times. The motor should run for 10 seconds.
5. Konfirmasi: Press the 'OK' button on the remote. The light adjust function is now active.

4.4 Cancelling an Emitter (Refer to Figure 3, 'Cancel Emitter')

To remove a paired remote control from the receiver:

1. Pareum listrik: Pegatkeun sambungan kakuatan ka panarima.
2. Daya Hurung: Sambungkeun deui kakuatan ka panarima.
3. Press P2 Button: Press the P2 button on the remote control once. The motor should run for 1 second.
4. Press P2 Seven Times: Press the P2 button on the remote control seven times. The motor will continuously work.
5. Konfirmasi: Press the 'OK' button on the remote to confirm cancellation.

5. Spésifikasi

6. Pangropéa

The DOOYA DC73A Wireless Receiver requires minimal maintenance. Keep the unit clean and free from dust. Do not attempt to open the casing unless you are a qualified technician, as it contains sensitive electronic components. Ensure the power supply is stable and within the specified voltage rentang.

7. Cara ngungkulan

• Motor teu ngaréspon: Check power connections to the receiver and motor. Ensure the remote control batteries are not depleted. Re-attempt the pairing process (Section 4.1).
• rentang kawates: Ensure there are no new obstructions between the remote and receiver. Check for sources of interference.
• Motor runs continuously: This might indicate an incorrect setting or a stuck P2 button. Try cancelling the emitter (Section 4.4) and re-pairing, or perform a factory reset if available (refer to the full PDF manual).

8. Tips pamaké

• The DC73A is specifically designed for 4-wire motors. Ensure your motor is compatible before installation.
• If you are looking for a specific remote control model like DC174A, confirm its compatibility with the DC73A receiver.
• Always test the motor's full range of motion and limit settings after installation and pairing.

9. Garansi jeung Rojongan

For detailed warranty information or technical support, please contact your seller or the manufacturer directly. A comprehensive user manual in PDF format is available for further reference:

View Manual Pamaké (PDF)