1. Produk Langkungview
This 433.92MHz rolling code remote control is designed for compatibility with various garage door openers and gate systems. It features a robust design and multiple buttons for controlling different functions or devices.
Naon Kaasup:
- Unit kadali jauh
- Pre-installed Battery
- Gantungan konci
- English Manual (this document)
Gambar 1: Hareupeun view of the 4-button remote control.
2. Spésifikasi
| Fitur | Rincian |
|---|---|
| Nomer modél | 433mhz Rolling Code |
| Métode Encoding | Kodeu rolling |
| Frékuénsi Operasi | 433.92MHz |
| Sertifikasi | CE |
| Asalna | Daratan Cina |
| Pakét Panjang | 13 cm |
| Bungkusan Lebar | 9 cm |
| pakét Jangkungna | 2 cm |
| Beurat pakét | 0.047 kg |
3. Setelan sareng Pemrograman
This remote uses rolling code technology, which requires pairing directly with your receiver unit (garage door opener or gate motor). The exact pairing procedure varies by manufacturer. Please refer to your original receiver's manual for specific instructions. Below is a general guide for common rolling code systems.
General Pairing Procedure:
- Locate the 'Learn' or 'Program' Button on Your Receiver: This button is typically found on the motor unit of your garage door opener or gate system. It might be labeled 'Learn', 'Code', 'Program', or have a small LED indicator next to it.
- Activate Learning Mode: Press and release the 'Learn' button on your receiver. The LED indicator on the receiver will usually light up or flash, indicating it is in learning mode. This mode typically lasts for a short period (e.g., 10-30 seconds).
- Programkeun Remote Anyar: While the receiver is in learning mode, press and hold the desired button on your new 433.92MHz remote control (e.g., button 'A' as shown in Figure 1). Keep the button pressed until the receiver's LED indicator changes (e.g., flashes rapidly, turns off, or lights solid), confirming successful pairing.
- Nguji Jauh: Release the button on the remote. Wait a few seconds, then press the programmed button again to test if it operates your garage door or gate.
- Program Additional Buttons (Optional): If your remote has multiple buttons and you wish to control other devices, repeat steps 2-4 for each additional button and corresponding receiver.
Important: If you encounter difficulties, consult the manual for your specific garage door opener or gate system. Some systems may require a different sequence or have specific timing requirements.
4. Ngoperasikeun Remote Control
Once successfully programmed, operating your remote control is straightforward:
- Pers Tunggal: Press the programmed button once to activate the associated device (e.g., open/close garage door, open/close gate).
- rentang: Ensure you are within effective operating range of your receiver. Obstructions and environmental factors can affect signal strength.
5. Pangropéa
Ngagantian batré:
The remote control uses a standard small coin cell battery (e.g., CR2032). When the remote's range decreases significantly or the LED indicator (if present) fails to light up, it's time to replace the battery.
- Buka remot kontrol kalayan ati-atiasing using a small screwdriver or a thin prying tool.
- Cabut batré anu lami, perhatikeun polaritasna (+/-).
- Pasangkeun batré anyar anu jinisna sami, pastikeun polaritasna leres.
- Tutup casing aman.
beberesih:
Wipe the remote control with a soft, dry cloth. Do not use abrasive cleaners or immerse the remote in water.
6. Cara ngungkulan
- Jauh teu tiasa dianggo saatos program:
- Ensure the receiver was in learning mode during programming.
- Pariksa batré jauh.
- Verify that your receiver is compatible with 433.92MHz rolling code remotes.
- Repeat the programming steps carefully, paying attention to timing.
- rentang operasi pondok:
- Replace the remote's battery.
- Ensure there are no major obstructions between the remote and the receiver.
- Check for sources of interference (e.g., other wireless devices, metal structures).
- Remote LED does not light up:
- The battery may be dead or incorrectly installed. Replace the battery.
- Ensure the remote is not damaged.
7. Tips pamaké
- Keep Original Remote Handy: Always keep your original remote control as a backup, especially during programming.
- Clear All Codes (If Needed): If you are having trouble programming, some receivers allow you to clear all existing remote codes before programming new ones. Consult your receiver's manual for this option.
- Hindarkeun Paparan Cai: While durable, the remote is not waterproof. Avoid exposing it to excessive moisture.
- Panyimpenan Aman: Store the remote in a safe place to prevent accidental button presses or loss.
8. Garansi jeung Rojongan
This product is covered by a standard manufacturer's warranty against defects in materials and workmanship. For specific warranty details or technical support, please contact the seller or refer to the product listing where you made your purchase. Keep your proof of purchase for warranty claims.
