1. Bubuka
This manual provides essential information for the installation, operation, maintenance, and troubleshooting of your new Roborock Laser Distance Sensor (LDS) module. The LDS module is a critical component of your robotic vacuum cleaner, responsible for accurate navigation and mapping of your home environment. This replacement part ensures your Roborock vacuum continues to operate with optimal performance.
2. Produk Langkungview
The Roborock LDS module LDS02RR is an original replacement part designed to restore the navigation capabilities of compatible Roborock robotic vacuum cleaners. It consists of a laser emitter, receiver, and a rotating mechanism that allows the vacuum to scan its surroundings and create a detailed map for efficient cleaning.
3. Spésifikasi
| Fitur | Rincian |
|---|---|
| Nomer modél | LDS02RR |
| Model cocog | Roborock S50, S51, S5 Max, S6, S7 |
| Tipe Bagian | Laser Distance Sensor (LDS) Module |
| Bahan | PVC |
| Dipeunteun Voltage | 5V DC |
| Dipeunteun Ayeuna | 0.35A |
| Kelas laser | Kelas 1 Laser Produk |
| Asalna | Daratan Cina |
| Ukuran Paket (L x W x H) | 15 cm x 12 cm x 8 cm |
| Beurat pakét | 0.4 kg |
4. Setup jeung Instalasi
penting: Before attempting any installation, ensure your robotic vacuum cleaner is powered off and disconnected from its charging dock. Proceed with caution and refer to your specific vacuum cleaner's service manual for detailed disassembly instructions if available.
- Pareum listrik: Turn off your Roborock vacuum and remove it from the charging base.
- Access the LDS Module: Depending on your specific Roborock model (S50, S51, S5 Max, S6, S7), you may need to remove the top cover or a specific panel to access the existing LDS module. This typically involves unscrewing several small screws.
- Pegatkeun sambungan kabel: Carefully disconnect the wiring harness connected to the old LDS module. Note the orientation of the connector to ensure correct reassembly.
- Hapus Modul Old: Unscrew any retaining screws holding the old LDS module in place and gently lift it out.
- Pasang Modul Anyar: Place the new LDS02RR module into position, ensuring it sits correctly. Secure it with the retaining screws.
- Sambungkeun Wiring: Reconnect the wiring harness to the new LDS module, ensuring a secure connection.
- Pasang deui: Reattach any covers or panels removed during disassembly, securing them with screws.
- Daya Hurung: Place the vacuum back on its charging dock or manually power it on. The vacuum should perform a self-check.
5. Parentah Operasi
Once the new LDS module is correctly installed, your Roborock robotic vacuum cleaner should resume normal operation. The vacuum will automatically utilize the new sensor for navigation, mapping, and obstacle avoidance. No special configuration is typically required for the LDS module itself after installation.
- Initiate a cleaning cycle via the Roborock app or the physical buttons on the vacuum.
- Observe the vacuum's navigation. It should move smoothly and map its environment accurately.
- If the vacuum exhibits unusual navigation patterns or errors, refer to the troubleshooting section.
6. Pangropéa
To ensure the longevity and optimal performance of your LDS module, regular maintenance is recommended:
- Clean the Sensor Window: Periodically wipe the transparent window on the top of the LDS turret with a soft, dry cloth. Dust or debris on this window can obstruct the laser and impair navigation.
- Pariksa keur halangan: Ensure there are no foreign objects or hair tangled around the rotating part of the LDS module.
- Hindarkeun Cairan: Do not use water or cleaning solutions directly on the LDS module, as this can damage internal electronic components.
7. Cara ngungkulan
If you encounter issues after installing the new LDS module, consider the following:
- Vacuum Reports "LDS Error" or Navigation Issues:
- Ensure the LDS module is securely installed and all connections are firm.
- Check for any physical obstructions preventing the LDS turret from rotating freely.
- Clean the LDS sensor window thoroughly.
- Restart the vacuum cleaner.
- Vacuum Cannot Create or Update Map:
- Verify that the LDS module is rotating during operation. If not, the motor or belt might be faulty (though this is a new part, inspect for shipping damage).
- Ensure adequate lighting in the room, although LDS typically works well in low light, extreme darkness can sometimes affect initial mapping.
- Unusual Noises from LDS Area:
- Check for any loose screws or components within the LDS housing.
- Ensure the module is seated correctly and not rubbing against other parts of the vacuum.
8. Tips pamaké
- This LDS module is intended as a direct replacement part. It is not an upgrade but rather a component to restore original functionality.
- When replacing, take photos of the disassembly process to aid in reassembly.
- Handle the module with care, especially the optical components and the rotating mechanism.
9. Garansi jeung Rojongan
For warranty information and technical support, please refer to the original purchase documentation or contact the seller directly. Keep your proof of purchase for any warranty claims. This product is designed as a replacement part for specific Roborock models; ensure compatibility before installation.
