MKS Monster8 V2 Control Board User Manual

1. Bubuka

The MKS Monster8 V2 is an advanced 8-axis 32-bit control board designed for high-performance 3D printers, particularly suitable for Voron printers. It features a powerful STM32F407VET6 microcontroller, enhanced protection circuits, and extensive connectivity options, making it a versatile choice for complex 3D printing setups. This manual provides detailed instructions for setting up, operating, and maintaining your MKS Monster8 V2 board.

2. Spésifikasi

3. Fitur konci

• 8-Axis Control: Supports up to 8 stepper motors for complex motion systems.
• 32-bit Microcontroller: Powered by STM32F407VET6 for high processing power.
• Voron Printer Compatibility: Optimized for use with Voron 3D printers.
• Enhanced Temperature Measurement: Includes a dedicated MAX31865 temperature measurement interface.
• Dukungan Tampilan: Compatible with MKS TS35 and MKS MINI12864 V3 displays, with U-disk file display capability.
• Konéktipitas Modern: Features a Type-C USB port for online serial communication and firmware updates.
• Wireless Ready: Integrated WiFi module slot for optional wireless connectivity.
• Raspberry Pi Power: Dedicated independent DC5V/3A power supply for Raspberry Pi integration.
• Integrated EEPROM: Mainboard includes 4KB EEPROM for configuration storage.
• Perlindungan anu kuat: MOS circuit, endstops circuit, and temperature measurement circuits are protected with resistors and Schottky diodes for increased reliability.

4. Setup Guide

4.1 Idéntifikasi komponén

Familiarize yourself with the various ports and components on the MKS Monster8 V2 board using the diagram below.

1. Motor driver slot
2. Heated bed connection
3. Input catu daya
4. Nyetir voltage pilihan
5. Kaluaran 5V
6. MAX31865 interface
7. I2C/CAN/UART1 expansion port
8. TF card signal SPI3 expansion port
9. slot kartu TF
10. WiFi module slot
11. Normally open fan voltage pilihan
12. Controllable fan voltage pilihan
13. Z+ endstops voltage selection, 5V or VIN
14. DIAG signal
15. panganteur tampilan
16. panganteur USB-C
17. External stepper driver connection
18. U port disk

4.2 Diagram Wiring

Carefully follow the pinout diagram for all electrical connections. Incorrect wiring can damage the board or connected components.

4.3 Stepper Driver Installation and Microstep Configuration

Before installing or removing stepper drivers, ensure the board is completely powered off. Refer to the tables below for microstep configuration using jumpers.

4.4 Sambungan tampilan

The MKS Monster8 V2 supports MKS TS35 and MKS MINI12864 V3 displays. Connect your chosen display to the appropriate EXP1 or EXP2 interface as indicated on the board.

5. Parentah Operasi

5.1 Firmware Installation and Update

The MKS Monster8 V2 supports Marlin and Klipper firmware. Firmware can be updated via the Type-C USB port. Refer to the official Makerbase GitHub repository for the latest firmware versions and detailed flashing instructions.

• Repositori GitHub: https://github.com/makerbase-mks/MKS-Monster8

5.2 Panggunaan Tampilan

If using a compatible LCD display, you can read and display files directly from a U-disk connected to the board's U-disk port. Navigate through the display menu to access U-disk functions.

6. Pangropéa

• Tetep Bersih: Regularly clean the board to prevent dust accumulation, which can lead to overheating or short circuits. Use compressed air or a soft brush.
• Pariksa sambungan: Periodically inspect all wiring and connections to ensure they are secure and free from damage.
• Power Off Before Changes: Always power off and disconnect the power supply before making any changes to wiring, installing/removing drivers, or connecting/disconnecting peripherals.
• Kaayaan Lingkungan: Operate the board within recommended temperature and humidity ranges to ensure optimal performance and longevity.

7. Cara ngungkulan

• Papan Henteu Nyala: Verify the power supply connections and ensure the input voltage is within the DC12V-24V range. Check the pluggable fuse for continuity.
• Stepper Motors Not Moving: Check motor wiring, stepper driver installation, and microstep jumper settings. Ensure the firmware is correctly configured for your motor setup.
• Tampilan Teu Gawé: Confirm the display is correctly connected to EXP1 or EXP2. Verify display type compatibility and firmware configuration.
• Communication Issues (USB/WiFi): Ensure correct drivers are installed on your computer for the Type-C port. If using WiFi, check module installation and network configuration in firmware.
• Thermal Runaway/Incorrect Temperature Readings: Verify thermistor wiring and MAX31865 connections. Ensure thermistor type is correctly configured in firmware.

8. Tips pamaké

• Firmware Customization: Candak advantage of the Marlin and Klipper support to fine-tune your printer's performance. Klipper, in particular, can offload processing to a Raspberry Pi, improving print quality and speed.
• Utilize Raspberry Pi Power: The dedicated 5V/3A power supply for Raspberry Pi simplifies integration and ensures stable power for your host computer.
• Leverage Protection Features: The V2 board's enhanced protection circuits (Schottky diodes) offer better resilience against wiring errors and electrical spikes. However, always exercise caution during installation.
• Sumberdaya Komunitas: Engage with the 3D printing community and Makerbase forums for additional tips, configurations, and troubleshooting advice.

9. Garansi jeung Rojongan

For technical support, firmware updates, and additional resources, please visit the official Makerbase GitHub repository for the MKS Monster8 V2:

• GitHub: https://github.com/makerbase-mks/MKS-Monster8

This resource provides access to documentation, firmware files, and community support. Please refer to the seller's terms for specific warranty information.