Bubuka
Thank you for choosing the Baseus Magnetic Bracket SUYZD-01 Car Phone Holder. This manual provides detailed instructions for the proper installation, operation, and maintenance of your device. Please read this manual thoroughly before use to ensure optimal performance and safety.
Setup sareng Instalasi
Follow these steps to properly install your magnetic car phone holder:
- Pilih Lokasi Pamasangan: Select a flat, clean surface on your car's dashboard or any other desired location. Ensure the surface is free from dust, grease, and moisture for optimal adhesion.
- Prepare the Holder: The holder comes with a special adhesive tape on its base. Peel off the protective film from the adhesive tape.
- Gantelkeun Panyekel: Firmly press the holder onto the chosen surface. Apply pressure for at least 30 seconds to ensure a strong bond. Allow the adhesive to cure for a few hours (ideally 24 hours) before attaching your phone.
- Nyiapkeun Telepon Anjeun:
- Option 1 (Directly on Phone/Case): Attach the included metal plate directly to the back of your smartphone or its protective case. Ensure the surface is clean before applying the plate.
- Option 2 (Under Case): For a less visible setup, place the metal plate between your phone and its protective case. Ensure the case is not too thick, as this may reduce magnetic strength.
Parentah Operasi
Using your Baseus Magnetic Bracket is straightforward:
- Ngahubungkeun Telepon Anjeun: Once the holder is securely installed and the metal plate is on your phone, simply bring the back of your phone (where the metal plate is located) close to the magnetic surface of the holder. The powerful magnets will automatically secure your phone in place.
- Nyaluyukeun Viewdina Angle: The holder features a hinge design that allows for universal 360-degree rotation. Gently pivot and rotate your phone to achieve the most comfortable and safe viewing angle for navigation, music, or calls.
- Nyabut Telepon Anjeun: To remove your phone, simply pull it away from the magnetic surface. The strong magnetic connection ensures your phone stays put during your drive but allows for easy one-handed removal when needed.
Perawatan sareng Pangropéa
To ensure the longevity and optimal performance of your Baseus Magnetic Bracket, please follow these maintenance guidelines:
- beberesih: Wipe the holder's surface with a soft, damp cloth to remove dust and grime. Avoid using harsh chemicals or abrasive cleaners, as these can damage the material.
- Adhesive Care: If you need to reposition the holder, carefully remove it and clean any adhesive residue from the surface. For re-installation, new adhesive tape may be required to ensure a secure bond.
- Lempeng magnét: Ensure the metal plate on your phone or case remains clean and free of debris to maintain a strong magnetic connection.
- Panyalindungan: The holder features a soft protective cover to prevent scratches on your smartphone. Periodically check this cover for wear and tear.
Pamérésan masalah
If you encounter any issues with your Baseus Magnetic Bracket, refer to the following common problems and solutions:
- Problem: Phone does not hold securely or falls off.
-
Solusi:
- Ensure the metal plate is correctly positioned on your phone or inside your case, directly over the magnetic area.
- Check if your phone case is too thick, as this can weaken the magnetic connection. Try removing the case or placing the metal plate on the outside of the case.
- Verify that the magnetic surface of the holder and the metal plate are clean and free of obstructions.
- Confirm that the holder itself is firmly attached to the dashboard and has not come loose.
- Problem: Holder does not stick firmly to the dashboard.
-
Solusi:
- Ensure the dashboard surface was thoroughly cleaned and dried before applying the adhesive tape. Any dust, oil, or moisture can prevent proper adhesion.
- Apply firm pressure for the recommended time during installation.
- Allow sufficient curing time (e.g., 24 hours) before placing a phone on the holder.
- If the adhesive has lost its stickiness, you may need to replace the adhesive tape with a new, strong automotive-grade adhesive.
spésifikasi
| Fitur | Rincian |
|---|---|
| Modél | SUYZD-01 |
| Warna | Hideung |
| Bahan | Aluminum Alloy + Soft Silicone Rubber + Magnetic Panel |
| Tipe Pamasangan | Adhesive base for dashboard/flat surface |
| Rotasi | Universal 360-degree rotation |
| Kasaluyuan | Universal for smartphones up to 6.4 inches, including iPhone 13/12/11 Pro/XS Max/XR/X/SE/5/6/6s/7/8 Plus, Xiaomi A3/Max 3/Mi 10/9T/8 se Lite/Redmi Note 7/8/8t/8s/9s Pro, Samsung S10/S9/S8/S7/S6 Edge Plus, and similar devices. |
| Fitur | Strong magnetic hold, durable metal body, soft silicone protection, single-hand operation, no impact on wireless charging. |
| Ukuran Paket (approx.) | 10 cm (L) x 6 cm (W) x 10 cm (H) |
| Beurat Paket (approx.) | 0.2 kg |
Tip pamaké
- For the strongest hold, ensure the metal plate is placed directly on your phone or a thin case, centered with the magnetic area of the holder.
- The magnetic design is engineered to have no impact on wireless charging functionality, allowing you to use compatible wireless chargers without removing the metal plate (if placed correctly).
- Consider the placement carefully before applying the adhesive, as repositioning might require new adhesive for optimal stickiness.
- This holder is also versatile and can be used on a desktop or table as a stand.
Garansi sareng Rojongan
This Baseus product is covered by a standard manufacturer's warranty against defects in materials and workmanship. For specific warranty terms and conditions, please refer to the documentation provided at the time of purchase or contact your retailer.
If you experience any issues or have questions regarding your Baseus Magnetic Bracket SUYZD-01, please contact the seller or Baseus customer support for assistance.
