Manual+

Scimagic-RC Tormatic MHS43-2

User Manual: Tormatic MHS43-2/MHS43-4 Compatible Remote Control

Model: Tormatic MHS43-2 | Brand: Scimagic-RC

1. Bubuka

This manual provides detailed instructions for the Scimagic-RC Tormatic MHS43-2/MHS43-4 compatible remote control, designed for 433.92MHz rolling code garage door openers. Please read these instructions carefully before use to ensure proper setup and operation.

Scimagic-RC remote control with compatibility list
The Scimagic-RC remote control, compatible with various Tormatic/Novoferm models including MAX 43-2, MAX 43-4, 502 2-CH, 504 4-CH, MHS43-2 NOVOTRON 302, MHS43-4 NOVOTRON 304, 512 MIX43-2 Mini Carbon, and MCHS43-2.

2. Spésifikasi

FiturKaterangan
Ngaran BrandScimagic-RC
Nomer modélTormatic MHS43-2
Métode EncodingKodeu rolling
Frékuénsi433.92MHz (433mhz)
Operasi Voltage12V DC 27A (battery included)
Jarak Pangiriman3-50 méter (ruang terbuka)
Kancing4
BahanMetal and PVC
SertifikasiCE
AsalnaDaratan Cina

Catetan: This is a third-party remote control, not manufactured by Tormatic/NOVOFERM. Transmission distance may vary significantly due to environmental interference such as walls, doors, or other obstructions.

3. Programming Instructions

To program your new remote control, you will need access to your garage door opener's receiver. Ensure you have access to the receiver/opener before proceeding.

  1. Locate the Receiver: Buka casing of your gate opener. The receiver is typically located next to the motor.
  2. Press Programming Button: On the receiver circuit board, press the programming button (often labeled ENR, MEMO, PROG, or REC, depending on your model) for 1-2 seconds and then release it. The LED light on the receiver should illuminate or blink, indicating it's in programming mode.
  3. Program New Remote: Take your new remote control and press the button you wish to use for 1 second.
  4. Konfirmasi Pemrograman: Release the button on the new remote. The LED light on the receiver will turn off immediately or within the next 10 seconds, depending on your model, confirming successful programming.

Important: This remote control cannot work with original systems using AES 128-bit coding.

Video demonstrating the programming process for the remote control with a receiver board.
Receiver board with remote control
Image showing a typical receiver board and the remote control during the programming process.
Close-up of receiver board and remote
A ngadeukeutan view of the receiver board and the remote control, highlighting the components involved in programming.
Remote control and receiver board interaction
Illustrates the interaction between the remote control and the receiver board during the programming sequence.
Remote control and receiver board setup
Another perspective of the remote control and receiver board setup for programming.
Remote control and receiver board overview
Hiji leuwihview of the remote control and receiver board, showing the general arrangement for programming.

4. Ngoperasikeun Remote Control Anjeun

Once programmed, your remote control is ready for use. Simply press the programmed button to activate your garage door or gate opener. The remote operates on a 433.92MHz frequency using rolling code technology for enhanced security.

Scimagic-RC remote control in hand
The Scimagic-RC remote control, ready for operation.

5. Pangropéa

Ngagantian batré

The remote control uses a 12V DC 27A battery. When the remote's range decreases significantly or the LED indicator on the remote does not light up when a button is pressed, it's time to replace the battery. To replace:

  1. Buka remot kontrol kalayan ati-atiasing.
  2. Cabut batré 12V 27A anu lami.
  3. Insert a new 12V 27A battery, ensuring correct polarity.
  4. Tutup casing aman.

Perawatan Umum

  • Jaga remot kontrol tetep garing sareng jauh tina suhu anu ekstrim.
  • Ulah ngaleupaskeun remot kontrol atawa ngabalukarkeun dampak anu kuat.
  • Bersihkeun remot nganggo lawon anu lemes sareng garing. Entong nganggo bahan kimia anu keras atanapi pembersih anu kasar.

6. Cara ngungkulan

  • Jauh teu tiasa dianggo saatos program: Double-check that you followed all programming steps correctly. Ensure your original remote system does not use AES 128-bit coding, as this compatible remote is not designed for such systems.
  • Reduced transmission range: This can be caused by environmental interference (walls, vehicles, etc.) or a low battery. Try replacing the battery and test in an open area.
  • LED on receiver not responding: Ensure the receiver is powered on and the programming button is pressed correctly. If the issue persists, consult your gate opener's original manual.

7. Tips pamaké

  • Always ensure you have direct line-of-sight to your garage door or gate when operating the remote for optimal performance.
  • Keep your original remote control in a safe place as a backup.
  • If you have multiple remotes, program each one individually following the steps in Section 3.

8. Garansi jeung Rojongan

For any issues or support inquiries, please contact the manufacturer:

  • Pabrikan: Shenzhen Scimagic Development Technology Co.Ltd
  • Alamat: Honghai Gebu Building 2301, Baoan Road, Songgang Baoan District, Shenzhen, Guangdong, China

Mangga tingal dokuméntasi pameseran Anjeun pikeun istilah jeung kaayaan jaminan husus.

Versi PDF tina manual pangguna sayogi kanggo diunduh: Manual Pamaké (PDF)

Dokumén Patali - Tormatic MHS43-2

Praview Scimagic-RC Gate Opener Remote Programming Guide
Step-by-step instructions for programming your Scimagic-RC gate opener remote control. Learn how to pair your new transmitter with your gate receiver.
Praview Scimagic-RC ATA PTX-4 Transmitter Code Storage Guide
User guide for storing transmitter codes on Scimagic-RC ATA PTX-4 garage door and gate opener systems. Includes step-by-step instructions.
Praview Product Manual: Remote Control Programming Guide
Concise guide on programming a new remote control to a receiver, covering different methods and troubleshooting tips. Includes instructions in multiple languages.
Praview Scimagic-RC PUJOL VARIO Remote Control Programming Guide
Step-by-step instructions for programming the Scimagic-RC PUJOL VARIO remote control for your receiver. Learn how to pair your new remote with your device.
Praview Scimagic-RC MARANTEC 868MHz Remote Control Programming Guide
Step-by-step instructions for programming Scimagic-RC MARANTEC 868MHz remote controls, including models like Digital 302, 304, 382, 384, 313, 321, 312. This guide covers code deletion and pairing.
Praview Scimagic-RC Garage Door Opener Remote Programming Guide
Concise guide to programming the Scimagic-RC garage door opener remote. Follow simple steps using the yellow round button and hand-held remote to pair your device for automatic garage door operation.