1. Bubuka
This manual provides detailed instructions for the safe and effective use of your Godox K-180A 180Ws Photography Studio Flash Strobe Light Kit. Please read this manual thoroughly before operating the equipment and keep it for future reference.
2. Émbaran Kasalametan
Always observe basic safety precautions when using electrical equipment to reduce the risk of fire, electric shock, or injury.
- Ulah ngalaan unit ka hujan atawa Uap.
- Do not disassemble the unit. If repairs are needed, contact qualified service personnel.
- Pastikeun vol kakuatantage matches the unit's requirements (AC220/60Hz or 110V/60Hz).
- Jauhkeun tina jangkauan barudak.
- Unplug the unit from the power source before cleaning or when not in use.
- Avoid prolonged continuous use of the modeling lamp; allow it to cool down for at least 1 minute after 5 minutes of continuous use to prevent overheating.
3. Eusi Paket
Verify that all items are included in your package (based on Kit 8, the most comprehensive option):
- 1x Godox K-180A Flash Unit
- 1x RT-16 Trigger (Transmitter and Receiver)
- 1x 180cm Light Stand
- 1x FS50X70cm Grid Softbox
- 1x Modeling Lamp
- 1x Kabel Listrik
4. Parentah Setup
4.1. Light Stand Assembly
Unfold the light stand legs and extend the telescopic sections to the desired height. Ensure all locking knobs are securely tightened.
4.2. Flash Unit Preparation
- Mount the K-180A flash unit onto the top stud of the light stand.
- Adjust the mounting bracket to achieve the desired angle and securely tighten it.
- The umbrella input is available for attaching a studio umbrella if desired.
4.3. Rakitan Softbox
Assemble the FS50X70cm Grid Softbox according to its specific instructions. Attach it to the universal mount on the flash unit.
4.4. RT-16 Trigger Setup
Insert the 23A 12V battery into the transmitter and 2 AAA batteries into the receiver (AAA batteries for receiver not included). Connect the receiver to the flash unit's sync port.
4.5. Sambungan Daya
Connect the power cord to the flash unit's power socket and then to a suitable AC power outlet. Ensure the power switch is in the OFF position before connecting.
5. Parentah Operasi
5.1. Daya Hurung / Pareum
Flip the Power Switch (labeled 'POWER') to turn the flash unit ON or OFF. The Charging LED Indicator will illuminate during charging.
5.2. Modeling Lamp Kontrol
Use the Modeling Light Switch (labeled 'MODEL') to turn the modeling lamp ON or OFF. Pushing it downwards (G position) turns it off, upwards (F position) turns it on. Note: Do not keep the modeling lamp on for too long; it is recommended to cool it down for 1 minute after 5 minutes of continuous use.
5.3. Flash Output Control
Rotate the Flash Output Controller (labeled with '+' and '-') to adjust the flash power. The output is stepless from 1/8 to full power. This allows for precise light requirements in different environments.
5.4. Tombol Test
To test the flash or before taking a picture, push the Test Button (labeled 'TEST'). This can also be used to adjust the brightness when combined with the flash output controller.
5.5. Slave Trigger Mode
The flash unit can be triggered synchronously with one external flash. This mode allows the K-180A to act as an auxiliary lamp, nawarkeun rupa-rupa épék cahaya jeung kalangkang.
6. Pangropéa
- beberesih: Use a soft, dry cloth to clean the exterior of the flash unit and accessories. Do not use abrasive cleaners or solvents.
- Panyimpenan: Store the kit in a cool, dry place, away from direct sunlight and excessive humidity.
- Ngagantian sekering: If the unit fails to power on, check the fuse. Replace it with a fuse of the same rating (5A).
7. Cara ngungkulan
- Lampu kilat henteu hurung:
- Check if the unit is powered on and connected correctly.
- Ensure the RT-16 trigger transmitter and receiver have fresh batteries and are properly synced.
- Verify the sync cord is securely connected to the flash unit.
- Pariksa sekering.
- Modél lamp teu jalan:
- Ensure the Modeling Light Switch is in the ON position.
- Pariksa lamun lamp bulb is securely installed and not burnt out.
- Kaluaran lampu kilat anu teu konsisten:
- Ensure the Flash Output Controller is set correctly.
- Allow sufficient recharging time between flashes.
8. Spésifikasi
8.1. Godox K-180A Flash Unit
| Fitur | Spésifikasi |
|---|---|
| Modél | K-180A |
| Kaluaran Flash | 180WS |
| Nomer Pituduh (m ISO 100) | 45 |
| Suhu Warna | 5600 ± 200K |
| Kakuatan Voltage | AC220/60Hz or 100V/60Hz (Optional, check your unit) |
| Flash Power Control | Stepless (1/8-full) |
| Modél Lamp | 75WS |
| Waktos Ngecas | 0.5-3 detik |
| Flash Triggering Model | Sync cord, Test button, Slave |
| Flash Lilana | 1/2000 / 1-an |
| sekering | 5A |
| Diménsi | 17 x 10 x 17.5cm (approx. 7.2 x 4.1 x 5.4in) |
| Beurat | Approx. 0.59KG (approx. 603g / 21.3oz) |
8.2. 180cm Light Stand
| Fitur | Spésifikasi |
|---|---|
| Beban Bearing | 2 kg |
| Telescopic Height | 82-200 cm |
| Jangkungna neundeun | 68 cm |
| Diaméter pipa | Φ1.6/1.9/2.2cm |
| Liang Screw | 1/4" |
| Beurat | 0.81 kg |
| Lipet Panjang | 67 cm |
| Min Panjang | 70cm (2'4") |
| Jangkungna Maksimal | 200cm (7') |
| Ideal Max. Working Height | 140-150 cm |
8.3. FS50X70cm Grid Softbox
| Fitur | Spésifikasi |
|---|---|
| Ukuran | 50 x 70cm / 20" x 27" |
| Gunung | Universal Gunung |
| Beurat | Kira-kira. 0.6 kg |
8.4. RT-16 Wireless Flash Trigger
| Fitur | Spésifikasi |
|---|---|
| Tipe | Wireless Flash pemicu |
| Saluran | 16 saluran |
| Input kakuatan pamancar | Batré 23A 12V (kaasup) |
| Input Daya Panarima | 2 * AAA batteries (not included) |
| Receiver Plug Size | 3.5 mm |
| Adapter Size for Receiver Plug | 3.5mm & 6.35mm |
| Radio Working Frequency | 433MHz |
| Laju Nyingkronkeun | 1/200s |
| Outdoor Operation Distance | Nepi ka 30m (ruang terbuka) |
| Indoor Operation Distance | Nepi ka 20m (ruang terbuka) |
| Ukuran Paket | 21.5 x 7.5 x 3.8cm / 8.5 x 3.0 x 1.5di |
| Beurat pakét | 125g / 4.4oz |
9. Tips pamaké
- Pamakéan Fotografi: This kit is primarily intended for photography, providing controlled lighting for studio setups. Experiment with different flash power settings and softbox positions to achieve desired lighting effects.
- Modél Lamp Pamakéan: While useful for previewing lighting, remember to give the modeling lamp breaks to prevent overheating and prolong its lifespan.
- Trigger Placement: For optimal wireless triggering, ensure a clear line of sight between the RT-16 transmitter and receiver, especially in indoor environments.
10. Garansi jeung Rojongan
Kanggo inpormasi garansi, dukungan téknis, atanapi patarosan jasa, mangga ngahubungi penjual atanapi produsén langsung. Simpen resi pameseran anjeun salaku bukti pameseran.