Home › Stauer › Stauer Watch Display Time Setting Instruction Manual

Stauer Watch Display Time Setting Instruction Manual

Stauer Watch Display Time Setting
Instruction Manual

WATCH DISPLAY

A – Crown

TIME SETTING

This watch is a manual wind that features luminous hour and minute hands.

To set the time: Locate the crown on your Stauer watch (diagram part A). Please note the two crown positions (0-1) in part A of the diagram.
Before the watch is worn for the first time, wind the crown, by hand, 25 to 30 cycles each day by rolling the crown clockwise (away from you) while in the “0” (zero) position.
To set the time: Pull the crown out to position “1” (part A) which will allow you to set watch hands for proper time selection. Once time is set, push crown back into original “0” (zero) position.

Visit us at www.stauer.com
to learn more about the fantastic
benefits of owning a Stauer Watch!
www.stauer.com

Documents / Resources

Watch Display Time Setting

Instruction Manual · Watch Display Time Setting

References

Stauer Jewelry - Afford the Extraordinarywww.stauer.com
User Manualmanual.tools

Published: June 9, 2021

Updated: June 11, 2021

Questions and answers

Helpful product questions tied to this manual. Each item links to the full Q&A page.

Questions & Answers

Use this section to ask about setup, compatibility, troubleshooting, or anything missing from this manual.

Gunther Wagner says:

May 3, 2022 at 5:11 pm
How about setting time on watch inside survival kit? No
instructions found. Once activated how can you change time?
Gunther Wagner asks How about setting time on watch inside survival kit? No
instructions found. Once activated how can you change time?

Manuals+ clarified question

Question

How do I set the time on the Stauer watch included in the survival kit?
Answer

Based on the Stauer Watch Display Time Setting manual, most manual-wind Stauer watches follow a standard procedure for setting the time and activating the movement. If your survival kit watch is a manual-wind model, follow these steps:

Locate the Crown: This is the small knob on the side of the watch (labeled as 'A' in the manual).

Winding (Activation): Before setting the time, ensure the watch is wound. While the crown is in the "0" (zero) position (pushed all the way in), roll the crown clockwise (away from you) for 25 to 30 cycles.

Setting the Time: Gently pull the crown out to position "1". Rotate the crown to move the watch hands to the correct time.

Finalize: Once the time is set, push the crown back into the original "0" position to start the watch.

If your survival kit watch is a digital or quartz model rather than manual-wind, these specific instructions may vary. If these steps do not work, please contact Stauer customer service at 888-333-2012 for model-specific assistance.
Read the full Q&A page
Reply
Joseph Kremers says:

January 14, 2024 at 5:49 am
I can’t get my Stauer Titanium Atomic Watch to set correctly, following the instructions. It kept time for several months, then the set time changed.
Joseph Kremers asks I can’t get my Stauer Titanium Atomic Watch to set correctly, following the instructions. It kept time for several months, then the set time changed.

Manuals+ clarified question

Question

How do I troubleshoot and set the time on my Stauer Titanium Atomic Watch?
Answer

It appears you are experiencing issues with a Stauer Titanium Atomic Watch. Please note that the manual provided on this page is for a standard Manual-wind Watch, which uses a mechanical crown for time setting. Atomic watches operate differently as they rely on radio signals (usually from the WWVB station in Colorado) to synchronize time automatically.

If your Atomic watch has stopped keeping correct time, please try the following troubleshooting steps typical for Stauer Atomic models:

Signal Reception: Ensure the watch is placed near a window overnight, facing towards Colorado, to allow it to receive the radio signal update.

Time Zone Selection: Atomic watches often require you to select your specific Time Zone (P, M, C, or E) before they can display the correct local time. Check if your watch has a button to cycle through these zones.

Battery Level: If the battery is low, the watch may lose its ability to sync or maintain the correct time. Consider having the battery tested or replaced.

Manual Reset: Most Stauer Atomic watches have a reset procedure (often involving holding a specific button for several seconds) to realign the hands to the 12:00 position before a new signal search.

Because the attached manual does not cover Atomic movements, we recommend contacting Stauer Customer Service at 800-859-1843 for the specific programming sequence for the Titanium Atomic model.
Read the full Q&A page
Reply