GA800 Variable Speed Drive
Buka ea Tataiso 
Kenya le ho qala Yaskawa VFD
Rev-04-03-2023-04PM
Kenya le ho Qala
APP #143
Tšen. 3.7.5
YASKAWA VFD
GA800 / A1000
FETOHA LEBELO MOQEBI
GA800 Variable Speed Drive
Lipotso life kapa life mabapi le tokollo ena, ikopanye le: support@mcscontrols.com
Micro Control Systems, Inc. 5580 Enterprise Parkway Fort Myers, Florida 33905
(239)694-0089 FAX: (239)694-0031 www.mcscontrols.com
Tlhahisoleseding e fuperweng tokomaneng ena e lokisitswe ke Micro Control Systems, Inc. mme e na le copyright © e sireleditswe 2023.
Ho kopitsoa kapa ho aba tokomane ena ho thibetsoe ntle le haeba ho amohetsoe ka ho hlaka ke MCS.
Setšoantšo sa GA800 / A1000 Hardware
Ho koaloa ha likhokahano ho pholletsa le S1-SN ho tla kenya tšebetsong taelo ea "RUN" ea Drive. Khanna tla ramp ho fihla ho Lower Limit e hlalosoang ke D2-02 ebe e laoloa ke 0-10Vdc ho pholletsa le Al-AC.
MCS YASKAWA AC DRIVE – GA800 / A1000 SETTINGS
HANBELL(Hardwired)VFD SETTINGS
| Senotlolo Likaroloana kenyeletsa: Qala/Emisa, 0-10V Lebelo Reference, Lebelo Referense Maikutlo | ||||
| A1000 Mekhahlelo & Litekanyetso | Paramethara Tlhaloso | Maikutlo | ||
| # | Boleng | Maikutlo | Boleng ba kamehla ho masakana (xxxxxx) | YEA / Mfg / Mosebelisi |
| A1-02 | 0 | V/f | “Khetha Mokhoa oa ho Laola”: 0=V/f; 1=V/fw/PG; 2=(Bula Loop); 3=Loop e koetsoeng | |
| B1-02 | 1 | “Matha Cmd Khetha: 0=Opereishene; 1=(Litheminale); 2=Modbus; 3=Kgetho | RUN=Koalo ea Khokahano ho S1-SN | |
| B1-03 | 1 | “Mokhoa oa ho Emisa”: 0=(Ramp); 1=Lebopo; 2=DC Inj; 3=Lebōpo la leoatle ka/nako | ||
| B1-04 | 1 | Tlosa Rev | “Tšebetso e Fetolelang”: 0=(E nolofalitsoe); 1=E holofetse | |
| B1-07 | 1 | Amohela Matha | “Matha a Sebaka/Remote”: 0=(Cycle Ext Run); 1=Amohela Ext Run | |
| B1-08 | 1 | Menus kaofela | "Matha Cmd" e Amoheletsoeng: 0 = (Feela ho Menu ea Ts'ebetso); 1=Menu kaofela | |
| B1-17 | 1 | Amohela Matha | “Matha Cmd ho PowerUp”: 0=(Cycle Ext Run); 1=Amohela Matha cmd | |
| C1-01 | 10 | "Acceleration Nako #1": Default=10 metsotsoana (range=0.0 - 6000.0) | ||
| C1-02 | 10 | "Deceleration Nako #1": Default=10 metsotsoana (range=0.0 - 6000.0) | ||
| C6-01 | 0 | “Khetha Mosebetsi oa ho Khanna”: 0=Boima ba Mosebetsi HD; 1=(Mosebetsi o Tloaelehileng ND) | ||
| C6-02 | 1 | Khetho ea "Carrier Frequency". PM motor, kamehla '2' = 5.0 kHz Mosebetsi o boima, kamehla '1' = 2.0 kHz Ts'ebetso e tloaelehileng ea Mosebetsi, kamehla '7' Swing PWM 1 |
||
| D2-02 | 35% | "Freq Ref Lower Limit": Ka tloaelo=0% (range=0.0 - 110% ea Parm E1-04) | 35% ea boleng ba E1-04 | |
| E1-01 | “Input Voltage”: Default= 230,460 (range=e ipapisitse le voltage sehlopha) | Mosebelisi o tlameha ho beha "Input Voltage” | ||
| E1-05 | BOHLOKOA VOLTAGE 220/440 | Mosebelisi o tlameha ho seta molumo oa motlakasetage | ||
| E2-01 | "Motor Rated FLA": Beha ka lebitso la koloi FLA | "Sebelisa MCC" | ||
| H4-02 | 50% | Sehlahisoa sa VDC sa Terminal FM | Moeli (50% = 5 VDC) | |
| H4-04 | 108 | Tlhahiso ea KW | U1-08 -E bonts'a tlhahiso ea KW ho tlhahiso ea AM. | |
| L1-01 | 2 | Mosebetsi oa VT | “Tshireletso ea Motlakase oa Motlakase”: 0=E holofetse; 1=(Kakaretso); 2=Mosebetsi oa VT | |
| L2-01 | 2 | CPU e sebetsa | “Tahlehelo ea Matla a Nakoana”: 0=(E holofetse); 1=L2-02; 2= CPU e tsosolositsoeng | |
| L5-01 | 0 | "Palo ea ho Restarts": Default=0 (range=0 - 10). | ||
| O1-03 | 0 | E khethiloe ke A1-02 | E seta yuniti ho hlahisa Hz bakeng sa referense ea khafetsa le lebelo la enjine. | |
Setšoantšo sa GA800 / A1000 MODBUS-I/O
MCS YASKAWA AC DRIVE – GA800 / A1000 SETTINGS
LITLHAKISO TSA HANBELL(MODBUS)VFD
| Senotlolo Likaroloana kenyeletsa: Qala/Emisa, 0-10V Lebelo Reference, Lebelo Referense Maikutlo | ||||
| A1000 Mekhahlelo & Litekanyetso | Paramethara Tlhaloso | Maikutlo | ||
| # | Boleng | Maikutlo | Boleng ba kamehla ho masakana (xxxxxx) | YEA / Mfg / Mosebelisi |
| A1-02 | 0 | V/f | “Khetha Mokhoa oa ho Laola”: 0=V/f; 1=V/fw/PG; 2=(Bula Loop); 3=Loop e koetsoeng | |
| B1-01 | 2 | Freq Ref Sel | E Seta Ketso ea Puisano ea Modbus – 1=E sebetsa ka thata; 2=Modbus; 3=Kgetho | |
| B1-02 | 2 | “Matha Cmd Khetha: 0=Opereishene; 1=E entsoe ka Hardware; 2=Modbus; 3=Kgetho | RUN=Koalo ea Khokahano ho S1-SN | |
| B1-03 | 1 | “Mokhoa oa ho Emisa”: 0=(Ramp); 1=Lebopo; 2=DC Inj; 3=Lebōpo la leoatle ka/nako | ||
| B1-04 | 1 | Tlosa Rev | “Tšebetso e Fetolelang”: 0=(E nolofalitsoe); 1=E holofetse | |
| B1-07 | 1 | Amohela Matha | “Matha a Sebaka/Remote”: 0=(Cycle Ext Run); 1=Amohela Ext Run | |
| B1-08 | 1 | Menus kaofela | "Matha Cmd" e Amoheletsoeng: 0 = (Feela ho Menu ea Ts'ebetso); 1=Menu kaofela | |
| B1-17 | 1 | Amohela Matha | “Matha Cmd ho PowerUp”: 0=(Cycle Ext Run); 1=Amohela Matha cmd | |
| C1-01 | 10 | "Acceleration Nako #1": Default=10 metsotsoana (range=0.0 - 6000.0) | ||
| C1-02 | 10 | "Deceleration Nako #1": Default=10 metsotsoana (range=0.0 - 6000.0) | ||
| C6-01 | 0 | “Khetha Mosebetsi oa ho Khanna”: 0=Boima ba Mosebetsi HD; 1=(Mosebetsi o Tloaelehileng ND) | ||
| C6-02 | 1 | Khetho ea "Carrier Frequency". PM, ea kamehla '2' = 5.0 kHz Mosebetsi o boima oa mosebetsi, kamehla '1' = 2.0 kHz Ts'ebetso e tloaelehileng ea Mosebetsi, kamehla '7' Swing PWM 1 |
||
| D2-02 | 35% | "Freq Ref Lower Limit": Ka tloaelo=0% (range=0.0 - 110% ea Parm E1-04) | 35% ea boleng ba E1-04 | |
| E1-01 | “Input Voltage”: Default= 230,460, 575 (range=e itshetlehile ka voltage sehlopha) | Mosebelisi o tlameha ho beha "Input Voltage” | ||
| E1-05 | BOHLOKOA VOLTAGE 220/440 | Mosebelisi o tlameha ho seta molumo oa motlakasetage | ||
| E2-01 | "Motor Rated FLA": Beha ka lebitso la koloi FLA | "Sebelisa MCC" | ||
| H1-01 | 25 | Terminal S1 Interlock (NC, kamehla fumana lebopo ho emisa) | ||
| H4-02 | 50% | Sephetho sa terminal FM VDC | Moeli (50% = 5 VDC | |
| H5-01 | 1 | Aterese ea Drive | E beha aterese ea lekhoba le sebelisoang bakeng sa likhokahano | |
| H5-02 | 5 | Comm Lebelo | E beha lebelo la puisano la Modbus | 38400bps |
| H5-03 | 0 | Parity Khetha | E beha palo ea palo hore e se ke ea lekana | |
| H5-04 | 1 | 1=Lebopo la ho Ema | Mokhoa oa ho emisa ka mor'a Phoso ea Puisano | |
| L1-01 | 2 | Mosebetsi oa VT | “Tshireletso ea Motlakase oa Motlakase”: 0=E holofetse; 1=(Kakaretso); 2=Mosebetsi oa VT | |
| L2-01 | 2 | CPU e sebetsa | “Tahlehelo ea Matla a Nakoana”: 0=(E holofetse); 1=L2-02; 2= CPU e tsosolositsoeng | |
| L5-01 | 0 | "Palo ea ho Restarts": Default=0 (range=0 - 10). | ||
| O1-03* | 0 | Seta yuniti ho hlahisa HZ bakeng sa referense ea khafetsa le lebelo la enjene | ||
Litlhophiso tsa kamehla tsa feme - 1F - E tlameha ho fetoloa: Motsu ho ea ho H5 01 - Motsu ho fihlela '01' ka ho panya ha otla kena.
Motsu ka ho le letona- fetola '1' ho '0' 'me u fetole 'F' ho ea '1'
Ho koaloa ha likhokahano ho pholletsa le S1-SN ho tla kenya tšebetsong taelo ea "RUN" ea Drive. Khanna tla ramp ho fihla ho Lower Limit e hlalosoang ke D2-02 ebe e laoloa ke 0-10Vdc ho pholletsa le Al-AC.
MCS YASKAWA AC DRIVE – GA800 / A1000 SETTINGS
CENTRIFUGAL Hardwired VFD Settings
| Senotlolo Likaroloana kenyeletsa: Qala/Emisa, 0-10V Lebelo Reference, Lebelo Referense Maikutlo | ||||
| A1000 Mekhahlelo & Litekanyetso | Paramethara Tlhaloso | Maikutlo | ||
| # | Boleng | Maikutlo | Boleng ba kamehla ho masakana (xxxxxx) | YEA / Mfg / Mosebelisi |
| B1-03 | 1 | “Mokhoa oa ho Emisa”: 0=(Ramp); 1=Lebopo; 2=DC Inj; 3=Lebōpo la leoatle ka/nako | ||
| B1-04 | 1 | Tlosa Rev | “Tšebetso e Fetolelang”: 0=(E nolofalitsoe); 1=E holofetse | |
| B1-07 | 1 | Amohela Matha | “Matha a Sebaka/Remote”: 0=(Cycle Ext Run); 1=Amohela Ext Run | |
| B1-08 | 1 | Menus kaofela | "Matha Cmd" e Amoheletsoeng: 0 = (Feela ho Menu ea Ts'ebetso); 1=Menu kaofela | |
| C1-01 | 15 | "Acceleration Nako #1": Default=15 metsotsoana (range=0.0 - 6000.0) | ||
| C1-02 | 90 | "Deceleration Nako #1": Default=90 metsotsoana (range=0.0 - 6000.0) | ||
| C6-02 | 7 | Khetho ea "Carrier Frequency". PM, ea kamehla '2' = 5.0 kHz Mosebetsi o boima oa mosebetsi, kamehla '1' = 2.0 kHz Ts'ebetso e tloaelehileng ea Mosebetsi, kamehla '7' Swing PWM 1 |
||
| D1-01 | 10Hz | "Hangata Ref 1 | ||
| D2-02 | 70% | "Freq Ref Lower Limit": Ka tloaelo=0% (range=0.0 - 110% ea Parm E1-04) | 70% ea boleng ba E1-04 | |
| E1-01 | “Input Voltage”: Default= 230,460 (range=e ipapisitse le voltage sehlopha) | Mosebelisi o tlameha ho beha "Input Voltage” | ||
| E2-01 | "Motor Rated FLA": Beha ka lebitso la koloi FLA | "Tlhokomeliso: beha ho Motor FLA" | ||
| H2-03 | 5 | "Freq discovery 2 e koetsoe: Khafetsa ea tlhahiso e kholo ho feta kapa e lekana le boleng ba L $ 01 ka hysteresis e khethiloeng ke L4-02 | ||
| H4-02 | 50% | Sephetho sa terminal FM VDC | Moeli (40% = 5 VDC | |
| H4-04 | 108 | Tlhahiso ea KW | U1-08 -E bonts'a tlhahiso ea KW ho tlhahiso ea AM. | |
| H4-05 | 50 | Multi-Function Analog output terminal AM e fumana | ||
| L5-01 | 0 | "Palo ea ho Restarts": Default=0 (range=0 - 10). | ||
| O1-03 | 0 | E khethiloe ke A1-02 | E seta yuniti ho hlahisa Hz bakeng sa referense ea khafetsa le lebelo la enjine. | |
Litlhophiso tsa CENTRIFUGAL MODBUS VFD
| Senotlolo Likaroloana kenyeletsa: Qala/Emisa, 0-10V Lebelo Reference, Lebelo Referense Maikutlo | ||||
| A1000 Mekhahlelo & Litekanyetso | Paramethara Tlhaloso | Maikutlo | ||
| # | Boleng | Maikutlo | Boleng ba kamehla ho masakana (xxxxxx) | YEA / Mfg / Mosebelisi |
| B1-01 | 2 | Freq Ref Sel | E Seta Ketso ea Puisano ea Modbus – 1=E sebetsa ka thata; 2=Modbus; 3=Kgetho | |
| B1-02 | 2 | “Matha Cmd Khetha: 0=Opereishene; 1=E entsoe ka Hardware; 2=Modbus; 3=Kgetho | RUN=Koalo ea Khokahano ho S1-SN | |
| B1-03 | 1 | “Mokhoa oa ho Emisa”: 0=(Ramp); 1=Lebopo; 2=DC Inj; 3=Lebōpo la leoatle ka/nako | ||
| B1-04 | 1 | Tlosa Rev | “Tšebetso e Fetolelang”: 0=(E nolofalitsoe); 1=E holofetse | |
| B1-08 | 1 | Menus kaofela | "Matha Cmd" e Amoheletsoeng: 0 = (Feela ho Menu ea Ts'ebetso); 1=Menu kaofela | |
| C1-01 | 15 | "Acceleration Nako #1": Default=15 metsotsoana (range=0.0 - 6000.0) | ||
| C1-02 | 90 | "Deceleration Nako #1": Default=90 metsotsoana (range=0.0 - 6000.0) | ||
| C6-02 | 7 | Khetho ea "Carrier Frequency". PM motor, kamehla '2' = 5.0 kHz Mosebetsi o boima, kamehla '1' = 2.0 kHz Ts'ebetso e tloaelehileng ea Mosebetsi, kamehla '7' Swing PWM 1 |
||
| D1-01 | 10Hz | "Hangata Ref 1 | ||
| D2-02 | 70% | "Freq Ref Lower Limit": Ka tloaelo=0% (range=0.0 - 110% ea Parm E1-04) | 70% ea boleng ba E1-04 | |
| E1-01 | “Input Voltage”: Default= 230,460 (range=e ipapisitse le voltage sehlopha) | Mosebelisi o tlameha ho beha "Input Voltage” | ||
| E2-01 | "Motor Rated FLA": Beha ka lebitso la koloi FLA | "Tlhokomeliso: beha ho Motor FLA" | ||
| H1-01 | 25 | Terminal S1 Interlock (NC, kamehla fumana lebopo ho emisa) | ||
| H2-03 | 5 | "Freq discovery 2 e koetsoe: Khafetsa ea tlhahiso e kholo ho feta kapa e lekana le boleng ba L $ 01 ka hysteresis e khethiloeng ke L4-02 | ||
| H4-01 | 108 | Matla a hlahisang | U1-08 - E bonts'a maqhubu a tlhahiso. Likarolo tsa lipontšo li khethoa ke 01-03 | |
| H4-02 | 50% | Sephetho sa terminal FM VDC | Moeli (40% = 5 VDC | |
| H4-04 | 102 | Khafetsa ea tlhahiso. | U1-02 -Bontša maqhubu a tlhahiso. Likarolo tsa lipontšo li khethoa ke 01-03 | |
| H4-05 | 50 | Multi-Function Analog output terminal AM e fumana | ||
| H5-01 | 1 | Aterese ea Drive | E beha aterese ea lekhoba le sebelisoang bakeng sa likhokahano | |
| H5-02 | 5 | Comm Lebelo | E beha lebelo la puisano la Modbus | 38400bps |
| H5-03 | 0 | Parity Khetha | E beha palo ea palo hore e se ke ea lekana | |
| H5-04 | 2 | 2:=Emisa kapele | Mokhoa oa ho emisa ka mor'a Phoso ea Puisano | |
| L5-01 | 0 | "Palo ea ho Restarts": Default=0 (range=0 - 10). | ||
| O1-03 | 0 | Seta yuniti ho hlahisa HZ bakeng sa referense ea khafetsa le lebelo la enjene | ||
Litlhophiso tsa kamehla tsa feme - 1F - E tlameha ho fetoloa: Motsu ho ea ho H5 01 - Motsu ho fihlela '01' ka ho panya ha otla kena. Motsu ka ho le letona- fetola '1' ho '0' 'me u fetole 'F' ho ea '1'
Letsatsi………………………Mongoli………………………..Revision………………..
| 8-3-15 | MONYANE | Tšen. 1.0 | Kenya le ho qala |
| 8-6-15 | MONYANE | Tšen. 1.0 | Liphetoho li entsoe |
| 2-11-16 | MONYANE | Tšen. 1.1 | Liphetoho tse entsoeng ho li-setting, leqepheng la 11 |
| 3-01-16 | MONYANE | Tšen. 1.2 | Liphetoho tse entsoeng ho li-setting, leqepheng la 11 |
| 3-7-16 | MONYANE | Tšen. 1.3 | Kenya setšoantšo se secha bakeng sa Hardwired |
| 3-8-16 | MONYANE | Tšen. 1.3 | Kenya ho seta ha Modbus le wiring |
| 3-14-16 | MONYANE | Tšen. 1.4 | Kenya Modbus, litlhophiso tsa Centrifugal |
| 3-28/29-16 | MONYANE | Tšen. 1.4 | Kenya hardwire dwg e ncha |
| 9-29-16 | MONYANE | Tšen. 1.5 | Kenya Litšoantšo tse ntlafalitsoeng |
| 1-11-17 | MONYANE | Tšen 1.6 | Liphetoho ho tsoa ho Bret |
| 1-12-17 | MONYANE | Tšenolo 1.5 | Lintlafatso tsa ho taka |
| 11-02-17 | MONYANE | Tšenolo 1.7 | Kenya liphetoho - b1-01- b1-02, H5-01 |
| 06-03-2019 | MONYANE | Tšenolo 3.0 | Kenya khetho ea C602 "Carrier Frequency". |
| 08-30-19 | MONYANE | Tšenolo 3.1 | E tlositsoe botlaaseng ba leqephe la 2 le leqepheng la 3 |
| 02-25-2020 | MONYANE | Tšenolo 3.2 | EKELA H-5-04 MODBUS FEELA |
| 05-15-2020 | MONYANE | Tšenolo 3.4 | KENYA E1-05 VOLTAGE MAX HANBELL HARDWIRED & MODBUS |
| 02-17-2021 | MONYANE | Tšenolo 3.5 | LIEKETSENG LITŠOANTŠISO |
| 07-26-2022 | MONYANE | Tšenolo 3.6 | LIEKETSENG PHAHAMA |
| 08-02-2022 | MONYANE | Tšenolo 3.6 | LIEKETSENG LITŠOANTŠISO |
| 08-05-2022 | MONYANE | Tšenolo 3.7.1 | HLAHALA LITŠOANTŠISO TSA HO FEELA |
| 01-05-2023 | MONYANE | Tšenolo 3.7.3 | Ntlafatso ea H1-01 INTERLOCK HO MODBUS SETTING |
| 04–3-2023 | MONYANE | Tšenolo 3.7.4 | TLOSA H1-01 HO SEBELISA HARDWIRED SETTING |
Litokomane / Lisebelisoa
 |
YASKAWA GA800 Variable Speed Drive [pdf] Buka ea Taelo GA800 Variable Speed Drive, GA800, Variable Speed Drive, Speed Drive, Drive |
 |
YASKAWA GA800 Variable Speed Drive [pdf] Tlhophiso Tataiso GA800, A1000, GA800 Variable Speed Drive, GA800, Variable Speed Drive, Speed Drive, Drive |