Smartbox ea Manual:
Smartbox user manual
Mofuta oa software 1.8
Selelekela
Smartbox e ka hlophisoa ka mekhoa e 4 e fapaneng ea ts'ebetso. Mokhoa o mong le o mong o na le ts'ebetso ea ona e ikhethang.
Smartbox e khona ho bala li-sensor tse fapaneng tse fapaneng. Li-analogue le li-sensor tsa dijithale li ka beoa leihlo. Li-inverters tse fapaneng li ka laoloa ke Smartbox V1.0. Liphetho tse tharo tse kholo li ka laoloa ka boikemelo ke Smartbox V1.0 Boitšoaro ba lihlahisoa tse kholo bo itšetlehile ka mokhoa o khethiloeng oa ho sebetsa oa Smartbox v1.0 Mode Fanauxbox retro.
Mokhoa oa Humidifier
Mokhoa oa Fanpumpbox
Mokhoa oa Fanpumpbox retro
Pele o qala kamehla etsa bonnete ba hore mokhoa o nepahetseng oa ts'ebetso o khethiloe, o tiisitsoe le ho kenngoa.
Mokhoa oa ho seta
- Smartbox V1.0 e ka hlophisoa ka mekhoa e 4 e fapaneng. Ho khetha mokhoa latela mehato e latelang
1 Tobetsa konopo ea holimo makhetlo a 'maloa ho fihlela KHETHA MODE e hlaha skrineng.
– 2 Tobetsa konopo ya kenya ho kenya menu
– 3 Kgetha mokgwa o mong ka ho thetsa konopo ya hodimo makgetlo a mmalwa ho fihlela mokgwa oo o o batlang o hlaha pontshong. 
– 4 Ho boloka mokgwa ho Smartbox V1.0 tobetsa konopo e tlase.
Fanauxbox V1.0 joale e tla boloka mokhoa ona mohopolong. Matheba a tla bontšoa pontshong nakong ya lenaneo.
Ho sebelisa smar tbox joalo ka fan-Auxbox e fetileng khetha MODE FANAUXBOX RETRO.
Mode Fanauxbox retro Tlhaloso e akaretsang
Litlhahiso tse 3 li ikarabella bakeng sa boemo ba liphetho OUT1 - OUT2 le OUT3 Lisebelisoa li ka letsohong le letšehali la Smartbox V1.0. Sehlahisoa se seng le se seng se ka fana ka 15A. Kakaretso ea maqhubu ha ea lokela ho feta 15A ka kakaretso.
Cable e kenyang RJ22 e hoketsoe ho maxi controller
Tlhahiso e le 'ngoe e hokahane le fan (e liehang / e potlakileng)
Out 2 e hlahisoang e hokahane le humidifier kapa dehumidifier (ho / tima)
Ho tsoa 3 ho hokahantsoe le heater (ho tima / ho tima)
Mode Humidifier Tlhaloso e akaretsang
Sebopeho sa humidifier se laola mongobo ka metsi a fetohang mouoane le ho a abela tikolohong ka kotloloho, ka ducting kapa hose ea kabo ea moea.
Metsi a ntse a tšeloa holim'a li-pads tse thibelang likokoana-hloko, ka li-pads tsena moea o omileng o futhumetseng o tla hlahisoa ke fan e matla, e tsamaisang moea o batang o mongobo tikolohong. (adiabatic cycle) Likarolo tse 'maloa li ka fetoloa ho boloka ts'ebetso e phahameng. Hape ho ekelitsoe likarolo tse ling ho etsa hore moea o be le homogeneous ka mor'a hore tikoloho e be mongobo o lakatsehang.
- fan ea motlakase P1.
- RH sensor P2.
– Mohloli oa metsi P3
- Sensor e khanyang P4
Sebopeho sa menu
Ho theha LDR
- Mefuta ea LDR Motšehare le Bosiu e khethoa ka ho metha leseli la tikoloho.
- LDR Off Day mode e lula e khethoa 24/7 (e lula e sebetsa)
Ho hlophisoa ha RH
- RH SET - E sebelisoa ha LDR e tima
- RH LETSATSI - E sebelisoa ka mokhoa oa Mots'eare (LDR e khethiloeng ka sekoting sa leseli)
- RH NIGHT - E sebelisoa ka mokhoa oa Bosiu (LDR e khethiloeng ka har'a sejana sa leseli)
tlhophiso ea FAN
- FAN max r Max percencetage fan (30%-100%)
– FAN min r Min percentage fan (0%-40%)
- FAN auto/manual
- Khetha taolo ea othomathike (PID e laoloa) / Lebelo la letsoho
- Buka ea FAN
-Lebelo la fan ka letsoho (0-100%)
Ho seta ho potoloha
- Nako ea ho potoloha 0 e bolela hore ha ho mokhoa oa ho potoloha 5 e bolela ho lieha ho 5min ho Potoloha
- Lebelo la ho potoloha 0-100% Lebelo la fan ka mokhoa oa ho potoloha
HLOKA tlhophiso
- HLOEKISA othomathike / buka ea ho khetha r U hloekile ka bohona kapa ka letsoho (Bohloeki ba metsi)
- HLOKA Nako = Nako e hloekileng ea nako e tsitsitseng 3-6-12-24 lihora Bukana 1-72 hora
tlhophiso ea MODE
- Humidifier r Smartbox V1.0 Humidifier
- Fanauxbox retro r Smartbox V1.0 Fanauxbox retro
- Fanpumpcontrol -Smartbox V1.0 Fanpumpcontrol
- Fanpumpbox retro r Smartbox V1.0 Fanpumpbox retro
Sesebelisoa sa PID
– P setup
- P parameter
– Ke seta
- Ke parameter
– D setup
- D parameter
Beep setup
– Beep On/Off
Litaba tsa SYS
- E bonts'a mofuta oa memori ea mofuta le boemo ba sensor ea Temp / Hum le boemo ba Inverter
Etsoa
– Khutlela pontshong ya menu e kgolo
Mode Fanpumpbox Tlhaloso e akaretsang
- Fanpumpbox e laola mocheso oa metsi ka litsamaiso tse peli tse tlatselletsang. E 'ngoe ke fene holim'a pholileng' me tse peli moloi oa pompo o potoloha mokelikeli tsamaisong. Li-sensor tse peli tsa mocheso oa NTC li ka eketsoa tsamaisong hammoho le li-sensor tse peli tsa khatello.
Hajoale ke sensor ea khatello e tlase e ntse e beiloe leihlo (khatello e tlase = pompo e tima). Li-sensor tsa mocheso li bitsoa Tin le Tout. Fene le pompo li ka laoloa ka har'a sejana sa inverter kapa se hlahisoang ke Mains ka pele. OUT1 bakeng sa fene le OUT2 bakeng sa pompo.
Hlokomela! Ha pompo e hoketsoe ho OUT 2, taolo ea pompo ea tima/e tima
– Tin P1.
- Tsohle P2.
- Port inverter fan P3.
- Pompo e fetolang boema-kepe P4.
- Sensor ea khatello e phahameng P5. (khetho)
- Sensor ea khatello e tlase P6.
- Input RJ22 (lehlakoreng) ho hokela pompo-sensor
Sebaka sa kutlo:
Sensor ea pompo
Kopanya sensor ea pompo (compressor on signal) holim'a mohala oa ho hokahanya ka har'a kamore ea motlakase ea Opticlimate.
Li-latches tsa sensor li tlameha ho hokeloa ho screw terminal 7 & N.
Hokela sensara ka "smartbox input" u sebelisa thapo ea puisano e fanoeng (RJ22)
Ka tlhophiso e mengata ea Opticallimate, daisy ketane e 'ngoe le e' ngoe ea pompo le e latelang e sebelisa thapo ea puisano lipakeng tsa li-sensor.
Sensor ea khatello
Sensor ea khatello ea LOW e tlameha ho kenngoa ka lehlakoreng la pompo ea suction (pele ho pompo) Sensor ea khatello ea HIGH e tlameha ho kenngoa ka lehlakoreng la khatello ea pompo (ka mor'a pompo) Ha khatello ea khatello ea lehlakoreng le tlaase e le tlase ho feta 0,5Bar, pompo e tla emisa ho qoba tšenyo ea pompo.
Li-sensor tsa mocheso
Sensor ea mocheso Tin e tlameha ho kenngoa phala e kenang ka har'a pholileng (e tsoang pompong) haufi le setsi sa metsi.
Sensor ea mocheso Tout e tlameha ho kenngoa phala e tsoang ho pholileng (e eang ho Opticlimate)
Tin e futhumetse ho feta Tout ka har'a sistimi e sebetsang. Latela metsu e mosehla holim'a phaephe ea koporo ea sehatsetsi ho thibela se ka hare le se ka ntle.
Kenya lisensara ka thapo e shebileng tlase ho qoba ho bala ho fosahetseng ka lebaka la lipokotho tsa moea tse qabeletsoeng liphaepheng.
Sensor ea mongobo
Kenya sensor ea mongobo haufi le sebaka seo mongobo o leng bohlokoa ho sona.
- Qoba mahlaseli a mocheso a tsoang maboneng kapa letsatsing.
- Qoba ho kenya sensor haufi le mosi oa moea oa humidifier. (ho palama baesekele)
Sensor ea ho lutla ha metsi
Kenya libaka tsa ho ikopanya le sensor ea metsi haufi le fatše.
Ha likhokahano li utloa metsi ka lebaka la ho lutla ha metsi, ponts'o e tsoang ho smartbox ea benya ebe phepelo ea metsi ea koaloa.
Ho kenya inverter
Kenya li-inverters ka thata leboteng sebakeng se omeletseng le se se nang condensation. Se ke oa sebelisa sebaka se kampetsoeng.
Bula sekoahelo ho etsa likhokahano.
Ho hokela smartbox ho inverter (RS485) Sebelisa thapo e fanoeng e fanoeng e nang le likhokahano tse ngotsoeng lipakeng tsa smartbox le inverter. 
Pompo
Sebopeho sa menu
HLOKOMELA SETUP
- E beha mocheso o lakatsehang oa tlhahiso ea metsi (30°C)
Tdelta SETUP
- E beha mocheso o phahameng oa delta lipakeng tsa Tout le Tin Steps ka likhato tse 0,5 (ΔT = 5)
HLOKOMELA NTC
- Lekanya NTC. Kenya sephetho sa Tout(pontshong) – Tactual(lekanya).
HLOKOMELA MOTSAMAI
-FAN MAX
Lebelo le phahameng la fan (30 - 100%)
-FAN MIN
Lebelo le fokolang la fan (0 - 40%)
TLHOKOMELISO EA PUMP P
-PUMP MAX
Pompo e phahameng ea lebelo (30 - 100%)
-PUMP MOTSOTSO
Pompo ea lebelo le tlase (0 - 30%)
Sesebelisoa sa PID
– P setup – P paramethara
- Ke seta - Ke parameter
- Setapo sa D – D paramethara
tlhophiso ea MODE
- Humidifier = Smartbox V1.0 Humidifier
– Fanauxbox retro = Smartbox V1.0 Fanauxbox retro
– Fanpumpcontrol =Smartbox V1.0 Fanpumpcontrol
– Fanpumpbox retro = Smartbox V1.0 Fanpumpbox retro
Beep setup
– Beep On/Off
Litaba tsa SYS
- E bonts'a mofuta oa memori ea mofuta le boemo ba sensor ea Temp / Hum le boemo ba Inverter
Etsoa
– Khutlela pontshong ya menu e kgolo
Mokhoa oa Fanauxbox retro
Tlhaloso e akaretsang
Maikutlo a 3 a ikarabella bakeng sa boemo ba liphetho OUT1 OUT2 le OUT3
Lintho tse kenang li ka letsohong le letšehali la Smartbox V1.0. E 'ngoe le e' ngoe e hlahisoang ke candeliver 15A. Kakaretso ea maqhubu ha ea lokela ho feta 15A ka kakaretso.
Cable e kenyang RJ22 e hoketsoe ho maxi controller
Tlhahiso e le 'ngoe e hokahane le fan (e liehang / e potlakileng)
Out 2 e hlahisoang e hokahane le humidifier kapa dehumidifier (ho / tima)
Ho tsoa 3 ho hokahantsoe le heater (ho tima / ho tima)
Litlhophiso tsohle li laoloa ke molaoli oa Maxi. Sebelisa bukana ea Maxi Controller bakeng sa tlhaloso.
Fanpumpbox retro Tlhaloso e akaretsang
Litlhahiso tse 3 li ikarabella bakeng sa boemo ba liphetho OUT1 OUT2 le OUT3 Lintho tse kenang li ka letsohong le letšehali la Smartbox V1.0.
Sehlahisoa se seng le se seng se ka fana ka 15A. Kakaretso ea maqhubu ha ea lokela ho feta 15A ka kakaretso.
Mokhoa oa retro oa Fanpumpbox ke oa ho khutlisetsa li-fanpumpcontroller tsa setaele sa khale u sebelisa FanAuxBox.
Kenyo:
KA NAKO/TS'O
Sheba lebokose la pompo la fan bakeng sa likeletso tsa ho kenya bakeng sa lebokose la pompo la fan retro
Litokomane / Lisebelisoa
 |
Smartbox V1.8 Smartbox Maxi Controller [pdf] Buka ea Mong'a V1.0, V1.8, V1.8 Smartbox Maxi Controller, Smartbox Maxi Controller, Maxi Controller, Controller |
