Manual Smartbox:
Smartbox mushandisi bhuku
Software vhezheni 1.8
Nhanganyaya
Iyo Smartbox inogona kugadzirwa mune 4 akasiyana maitiro ekushandisa. Imwe neimwe modhi ine yayo yakasarudzika mashandiro.
Iyo smartbox inogona kuverenga akasiyana akasiyana ma sensor. Analogue pamwe nedhijitari sensors inogona kutariswa. Akasiyana inverters anogona kudzorwa neiyo Smartbox V1.0. Matatu mains anobuda anogona kudzorwa akazvimiririra neSmartbox V1.0 Maitiro ezvinobuda mains anoenderana neakasarudzwa maitiro ekushandisa eSmartbox v1.0 Mode Fanauxbox retro.
Mode Humidifier
Mode Fanpumpbox
Mode Fanpumpbox retro
Usati watanga nguva dzose ita shuwa kuti nzira yekushandisa yakasarudzwa, yakasimbiswa uye yakatakurwa.
Setup mode
- Iyo Smartbox V1.0 inogona kurongwa mune mana akasiyana modhi. Kuti usarudze modhi tevera matanho anotevera
1 Bata kiyi yekusimudza kakawanda kusvika SARUDZA MODE yabuda pachiratidziro.
- 2 Bata bhatani rekupinda kuti uise menyu
- 3 Sarudza imwe modhi nekubata kiyi yekusimudza kakawanda kusvika iyo yaunoda modhi ichiratidza muchiratidziro. 
- 4 Kuchengeta modhi muSmartbox V1.0 bata kiyi yekudzika.
Iyo Fanauxbox V1.0 ikozvino ichachengeta iyi modhi mundangariro. Dots acharatidzwa pachiratidziro panguva yechirongwa.
Kuti ushandise smar tbox seyaimbova fan-Auxbox sarudza iyo MODE FANAUXBOX RETRO.
Mode Fanauxbox retro General tsananguro
3 mapopu ndiwo anokonzeresa mamiriro ezvakabuda OUT1 – OUT2 uye OUT3 Zvinopinza zviri kuruboshwe rweSmartbox V1.0. Imwe neimwe inobuda inogona kuunza 15A. Huwandu hwemazuvano hunogona kusapfuudza 15A pamwero.
Input RJ22 tambo yakabatana kune maxi controller
Kunze kwe1 kuburitsa kwakabatana kune fan (inononoka / nekukurumidza)
Kunze kwe2 kuburitsa kwakabatana kune humidifier kana dehumidifier (pa / kudzima)
Kunze kwe3 kubuda kwakabatana kune hita (pa / kudzima)
Mode Humidifier Tsananguro yakajairika
Iyo humidifier configuration inogadzirisa humidity nemvura inopfungaira uye inoiparadzira munharaunda yakananga, kuburikidza ne ducting kana mhepo yekuparadzira hose.
Mvura iri kuiswa pamusoro pe-anti-bacterial threaded pads, kuburikidza nemapadhi aya anodziya mhepo yakaoma inounzwa nemhepo ine simba, ichigovera mweya unotonhora wakanyorova munzvimbo. (adiabatic cycle) Nhamba dzinoverengeka dzinogona kuchinjwa kuti dzichengetedze kushanda kwakanyanya. Zvakare mamwe maficha akawedzerwa kuita kuti mhepo ive homogeneous mushure mekuwana nharaunda kune yaunoda humidity.
- inverter fan P1.
- RH sensor P2.
-Mvura detector P3
- Chiedza sensor P4
Menu chimiro
Kugadziriswa kweLDR
- LDR PaMasikati neHusiku modhi inosarudzwa nekuyera mwenje wenzvimbo.
- LDR Off Day modhi inogara yakasarudzwa 24/7 (yakagara iripo)
RH kugadzirisa
-RH SET - Inoshandiswa sezvo LDR ichidzima
- RH ZUVA - Inoshandiswa muZuva modhi (yakasarudzwa trough yekuona mwenje LDR)
-RH Husiku -Inoshandiswa muHusiku modhi (yakasarudzwa mwenje yekuona LDR)
FAN setup
- FAN max r Max muzanatage fan (30% -100%)
– FAN min r Min percentage fan (0% -40%)
- FAN auto/manual
-Sarudza otomatiki kudzora (PID yakarongedzwa) / Manual kumhanya
- FAN bhuku
-Manual fan kumhanya (0-100%)
Circulate setup
-Kutenderera nguva 0 zvinoreva kuti hapana kutenderera modhi 5 zvinoreva kunonoka kwemaminetsi mashanu kutenderera
-Kutenderera kumhanya 0-100% Fan kumhanya mukutenderera modhi
CLEAN setup
- CLEAN otomatiki / manyore Sarudza r otomatiki kana bhuku rakachena (Flush mvura buffer)
- CLEAN Period = Nguva yakachena nguva Yakagadziriswa 3-6-12-24 awa Manual 1-72 awa
MODE setup
- Humidifier r Smartbox V1.0 Humidifier
-Fanauxbox retro r Smartbox V1.0 Fanauxbox retro
- Fanpumpcontrol -Smartbox V1.0 Fanpumpcontrol
-Fanpumpbox retro r Smartbox V1.0 Fanpumpbox retro
PID setup
- P setup
- P parameter
- Ini ndakagadzira
- Ini parameter
- D setup
-D parameter
Beep setup
– Beep On/Off
SYS ruzivo
-Inoratidza vhezheni nhamba yekurangarira modhi uye chimiro Temp / Hum sensor uye Inverter mamiriro
Exit
- Dzokera kune main menu kuratidza
Mode Fanpumpbox General tsananguro
- Iyo fanpumpbox inodzora tembiricha yemvura neaviri anoenderana masisitimu. Imwe ndeye feni pane inotonhorera uye mbiri muroyi wepombi inotenderedza mvura muhurongwa. Maviri eNTC tembiricha sensors anogona kuwedzerwa kune sisitimu pamwe neaviri ekumanikidza sensors.
Parizvino chete iyo yakaderera pressure sensor iri kutariswa (yakaderera kudzvanywa = kupomba kure). Iwo Temperature sensors anonzi Tin uye Tout. Iyo feni uye pombi inogona kudzorwa muchidyiro inverter kana trough Mains kubuda kumberi. OUT1 yefani uye OUT2 yepombi.
Cherechedza! Kana pombi yakabatana neOUT 2, pombi yekudzora inobatidzwa/yakadzima
-Tin P1.
- Pamusoro peP2.
-Port inverter fan P3.
- Port inverter pombi P4.
-Kudzvanya sensor High P5. (sarudzo)
- Pressure sensor yakaderera P6.
- Input RJ22 (padivi) yekubatanidza pombi-sensor
Sensor nzvimbo:
Pombi sensor
Batanidza sensor yepombi (compressor pane chiratidzo) pane yekubatanidza bar mukati memagetsi compartment yeOpticlimate.
Iyo sensor latches inofanirwa kubatana kune screw terminal 7 & N.
Batanidza sensor neiyo smartbox yekupinda uchishandisa yakapihwa yekutaurirana tambo (RJ22)
Mune akawanda Opticlimate setup, daisy cheni imwe neimwe pumpsensor neinotevera uchishandisa tambo yekutaurirana pakati pezvinonzwa.
Pressure sensor
Iyo yekumanikidza sensor LOW inofanira kuiswa papombi suction-side (pamberi pepombi) Iyo yekumanikidza sensor HIGH inofanira kuiswa pane pombi yekumanikidza divi (kuseri kwepombi) Kana kudzvanywa kuri kumanikidza LOW side kwakaderera pane 0,5Bar, pombi ichamira kudzivirira kukuvara kwepombi.
Tembiricha sensors
Iyo tembiricha sensor Tin inofanirwa kuiswa papombi inopinda muinotonhorera (inobva papombi) pedyo neinotonhorera yemvura.
Iyo tembiricha sensor Tout inofanirwa kuiswa papombi inobuda muinotonhorera (inoenda kuOpticlimate)
Tin inodziya kupfuura Tout mune inoshanda sisitimu. Tevedzera miseve yeyero papombi yemhangura yemudziyo unotonhorera kuti udzivise zviri mukati uye zviri kunze.
Isa masensa netambo yakatarisa pasi kuti udzivise kuverenga kwakashata sensor nekuda kwehomwe dzemhepo dzakavharirwa mupombi.
Humidity Sensor
Isa humidity sensor pedyo nenzvimbo iyo humidity yakakosha.
-Dzivisa kupisa kwemwaranzi kubva kumwenje kana zuva.
-Nzvenga kuisa sensor padhuze nehumidifier mhepo inopera. (bhasikoro)
Sensor yekudonha kwemvura
Isa mvura sensor yekubatanidza nzvimbo padyo nepasi.
Kana iwo anobatika anzwa mvura nekuda kwekudonha kwemvura, chiratidziro chinobva kusmartbox chinopenya uye mvura inovharwa.
Inverter kuiswa
Isa ma inverters zvakasimba kumadziro munzvimbo yakaoma uye isina condensation yemahara. Usashandise enclosure.
Vhura chivharo kuti ugadzire zvinongedzo.
Kubatanidza smartbox kune inverter (RS485) Shandisa yakapihwa yakatsaurirwa tambo ine yakanyorwa zvinongedzo pakati pesmartbox uye inverter. 
Pombi
Menu chimiro
Tout SETUP
- Inoisa iyo inodiwa nzira yekubuda kwemvura tembiricha (30 ° C)
Tdelta SETUP
- Inoisa tembiricha yepamusoro yedelta pakati peTout neTin Matanho mu0,5 madhigirii (ΔT = 5)
NTC SETUP
- Gadzirisa NTC. Pinda mhedzisiro Tout (pakuratidzira) - Tactual (yakayerwa).
FAN SETUP
-FAN MAX
Maximal kumhanya fan (30 - 100%)
-FAN MIN
Minimal kumhanya fan (0 - 40%)
PUMP KUGADZIRA P
-PUMP MAX
Yakanyanya kumhanya pombi (30 - 100%)
-PUMP MIN
Pombi inomhanya diki (0 - 30%)
PID setup
- P setup - P parameter
– I setup – I parameter
- D setup - D parameter
MODE setup
- Humidifier = Smartbox V1.0 Humidifier
- Fanauxbox retro = Smartbox V1.0 Fanauxbox retro
– Fanpumpcontrol =Smartbox V1.0 Fanpumpcontrol
- Fanpumpbox retro = Smartbox V1.0 Fanpumpbox retro
Beep setup
– Beep On/Off
SYS ruzivo
-Inoratidza vhezheni nhamba yekurangarira modhi uye chimiro Temp / Hum sensor uye Inverter mamiriro
Exit
- Dzokera kune main menu kuratidza
Mode Fanauxbox retro
General tsananguro
Matatu ekuisa ndiwo ane chekuita nechimiro chezvakabuda OUT3 OUT1 uye OUT2
Izvo zvinopinza zviri kuruboshwe ruoko rweSmartbox V1.0. Imwe neimwe inobuda candeliver 15A. Huwandu hwemazuvano hunogona kusapfuudza 15A pamwero.
Input RJ22 tambo yakabatana kune maxi controller
Kunze kwe1 kuburitsa kwakabatana kune fan (inononoka / nekukurumidza)
Kunze kwe2 kuburitsa kwakabatana kune humidifier kana dehumidifier (pa / kudzima)
Kunze kwe3 kubuda kwakabatana kune hita (pa / kudzima)
Zvese zvigadziriso zvinodzorwa naMaxi controller. Shandisa Maxi Controller bhuku rekunyora.
Fanpumpbox retro General tsananguro
3 mapopu ndiwo anokonzeresa chimiro chezvinobuda OUT1 OUT2 uye OUT3 Zvinopinza zviri kuruboshwe rweSmartbox V1.0.
Imwe neimwe inobuda inogona kuunza 15A. Huwandu hwemazuvano hunogona kusapfuudza 15A pamwero.
Iyo Fanpumpbox retro modhi ndeyekudzoreredza ekare dhizaini fanpumpcontrollers uchishandisa FanAuxBox.
Input:
IN/OUT
Ona manual fan pombi bhokisi rekupa zano rekuisa ye fan pombi bhokisi retro
Zvinyorwa / Zvishandiso
 |
Smartbox V1.8 Smartbox Maxi Controller [pdf] Bhuku reMuridzi V1.0, V1.8, V1.8 Smartbox Maxi Controller, Smartbox Maxi Controller, Maxi Controller, Controller |
