Tataiso ea ho Qala ka Potlako
EM132-133
Ho kenya Mechine
BOHLOKOA
Ke basebetsi ba tšoanelehang feela ba ka etsang seta.
Mehloli eohle ea motlakase e kenang e tlameha ho tima nakong ea ho kenya. Nakong ea ts'ebetso ea Powermeter, hazardous voltagli teng ho li-terminals tsa ho kenya. Ho hloleha ho ela hloko litemoso ho ka baka kotsi e mpe kapa e bolaeang, kapa tšenyo ea thepa.
Ka kopo sheba bukana ea ho instola le ts'ebetso ho fumana lintlha tse ling.
Kemiso e Tloaelehileng ea Motlakase
| Tlhophiso ea Wiring | Khoutu ea ho seta |
| 3-terata 2-element Khokahanyo e tobileng e sebelisa 2 CTs | 3dir2 |
| Khokahano e tobileng ea 4-terata ea Wye 3 e sebelisa 3 CTs | 4Ln3 kapa 4LL3 |
| Khokahano ea 4-terata Wye 3-element e sebelisa 3 PTs, 3 CTs | 4Ln3 kapa 4LL3 |
| 3-terata 2-element Bula Delta khokahano e sebelisa 2 PTs, 2 CTs | 3OP2 |
| 4-terata Wye 2½ -element khokahanyo sebelisa 2 PTs, 3 CTs | 3Ln3 kapa 3LL3 |
| 3-terata 2½ -element Bula khokahano ea Delta u sebelisa 2 PTs, 3 CTs | 3OP3 |
| Khokahano e tobileng ea 4-terata 3-element Delta e sebelisa 3 CTs | 4Ln3 kapa 4LL3 |
| 3-terata 2½-elemente Broken Delta khokahanyo sebelisa 2 PTs, 3 CTs | 3bLn3 kapa 3bLL3 |
HLOKOMELA:
Sheba buka ea Instola le ts'ebetso bakeng sa litšoantšo tsa schematics tsa wiring
Kemiso ea Motlakase
Ho kenya MODULE
Karolo ena e sebetsa ho likarolo tsa I/O le tsa Puisano.
TLHOKOMELO
Pele o kenya I/O Module etsa bonnete ba hore mehloli eohle ea motlakase e kenang e koetsoe. Ho hloleha ho hlokomela mokhoa ona ho ka fella ka kotsi e tebileng kapa e bolaeang le tšenyo ea thepa.
Seta ea Motheo
Litlhophiso tsohle li ka etsoa ka kotloloho ho tsoa ho phanele ea ponts'o kapa ka likou tsa puisano ho sebelisa software ea puisano ea PAS, ntle le litlhophiso tsa Communications le Display, tse tlamehang ho etsoa ka kotloloho ho phanele ea lisebelisoa. 
Ho seta CT Primary current, etsa mehato e latelang:
- Tobetsa
bakeng sa 5sec, ho fihlela password ea no. ho panya - Kenya nomoro ea lekunutu u sebelisa
, ebe o tobetsa bakeng sa 2sec ebe ponts'o e ncha e nang le ho panya "Reset" - Tsamaea ka ho tobetsa haufinyane (ka tlase ho 1sec) fallela ho Basic setup
- Tobetsa bakeng sa 2sec, ho fihlela "Conf" e panya:
- Tsamaea ka ho tobetsa haufinyane (ka tlase ho 1sec) fallela ho CT setup
- Tobetsa bakeng sa 2sec, ho fihlela "5000" e panya, ebe o tobetsa haufinyane o sebelisa ho boleng bo batloang
- Tobetsa bakeng sa 2sec, ho fihlela “CT” e panya, ebe o tobetsa bakeng sa 2sec, ho fihlela "Basic" e panya, ebe o tobetsa bakeng sa 2sec, ho fihlela "Reset" e panya, tobetsa haufinyane sebelisa ho ya ho panya "Tswa" ebe o tobetsa bakeng sa 2sec ho khutlela skrineng sa pele
BONTŠA DATA
Ho tsamaea ka Mokhoa oa Pontšo
Phanele e ka pele e na le sebopeho se bonolo se u lumellang ho bonts'a litekanyo tse ngata ho fihla maqepheng a 38 a bonts'itsoeng. Bakeng sa ho bala habonolo, li-parameter li arotsoe ka lihlopha tse tharo; sehlopha ka seng se fumaneha ka ho tobetsa konopo ea senotlolo mme leqephe le leng le le leng la sehlopha le fumaneha ka ho tobetsa konopo ea senotlolo.
Pontšo ea pele e tšoana le e hlalositsoeng ka tlase: 
Tobetsa pele e tla bonts'a liparamente tsa tekanyo ea Matla, ka ho sututsa e tla ea ho imp., exp. e sebetsang/e sebetsa, joalo-joalo ... joalo ka ha ho hlalositsoe ka tlase: 
Ho sutumelletsa lekhetlo la bobeli e tla bonts'a liparamente tsa MAX DMD, ka ho sututsa e tla ea ho MAX DMD P, Q, S, I, joalo-joalo ... joalo ka ha ho hlalositsoe ka tlase: 
Ea boraro e sutumelletsa e tla bontša Votage/Litekanyo tsa hajoale, ka ho sututsa e tla ea ho V (LN), V (LL), I, Power, PF, THD, TDD, F, joalo-joalo ... joalo ka ha ho hlalositsoe ka tlase: 
| Khoutu | Paramethara | Dikgetho | Tlhaloso |
| ConF | Mokhoa oa wiring | 3OP2 | 3-terata e bulehileng delta e sebelisa 2 CTs |
| 4Ln3 | 4-terata Wye e sebelisa 3 PTs (ea kamehla) | ||
| 3dir2 | Khokahano e tobileng ea terata e 3 e sebelisa 2 CTs | ||
| 4LL3 | 4-terata Wye sebelisa 3 PTs | ||
| 3OP3 | 3-terata e bulehileng delta e sebelisa 3 CTs | ||
| 3Ln3 | 4-terata Wye sebelisa 2 PTs | ||
| 3LL3 | 4-terata Wye sebelisa 2 PTs | ||
| 3bLn3 | 3-terata Broken delta sebelisa 2 PTs, 3 CTs | ||
| 3bLL3 | 3-terata Broken delta sebelisa 2 PTs, 3 CTs | ||
| Pt Karolelano | PT karo-karolelano | 1.0 * - 6,500.0 | Tekanyo e ka bang teng ea transformer |
| Ntlha ea Pt | |||
| Ct | CT ea mantlha ea hona joale | 1-50,000A
(5*) |
Tekanyetso ea mantlha ea transformer ea hajoale |
| PowDmdPer | Nako ea tlhokahalo ea matla | 1, 2, 5, 10, 15*, 20,
30, 60, E |
Bolelele ba nako ea lipalo tsa tlhoko ea motlakase, ka metsotso. E = amahanyo kantle |
| Num.Per. | Palo ea linako tsa tlhoko ea matla | 1-15 (1*) | Palo ea linako tsa tlhokahalo e lokelang ho lekanngoa bakeng sa fensetere e thellang e batla 1 = palo ea tlhokahalo ea nako ea thibelo |
| ADmdPer. | Ampere/Volt nako ya tlhokeho | 0-1800 (900*) | Bolelele ba nako ea volt/amplipalo tsa tlhokahalo, in metsotsoana. 0 = ho lekanya tlhōrō ea hona joale |
| Khafetsa | Leqhubu la lebitso | 25, 50, 60, 400 (Hz) | Leqhubu la tšebeliso ea matla ka lebitso |
| MaxDmdLd |
Boemo ba COM1
| Khoutu | Paramethara | Dikgetho | Tlhaloso |
| Protocol | Tsamaiso ea puisano | ASCII*, rtu, dnP3 | ASCII, Modbus RTU (ea kamehla) kapa protocol ea DNP3.0 |
| Sehokedi | Interface standard | 485 | RS-485 interface (ea kamehla) |
| Aterese | Aterese | ASCII: 0 (ea kamehla) - 99, Modbus: 1 (ea kamehla) -247, DNP3.0: 0 (ea kamehla) -255 | |
| Baud Rate | Sekhahla sa Baud | 110, 300, 600, 1200, 2400, 4800, 9600 (ea kamehla), ho fihla ho 115,200 bps | |
| Lintlha/Mokha | Sebopeho sa data | 7E, 8E (7/8 bits, even parity), 8n (default) (8 bits, no parity) | |
| Snd.Tieha | |||
Lintlha tsa Kenyelletso le Sephetho
| 3 matlatage inputs | 57/98-400/690 VAC | HO HLAHALA KA HO TSAMAISA - Lebitso: 690V line-to-line voltage, boholo ba 828V; 400V line-to-neutral, 480V boholo - Moroalo: <0.5 VA. HO KENYA HO SEBELISA PT - Moroalo: <0.15 VA | |
| Moqtagli-terminals tsa ho kenya | 4 x Boholo ba karolo ea terata: 2.5 mm² (12 AWG) | ||
| Li-nputs tse 3 tsa hona joale (Tlhaloso ea Galvanic) | /5A(10A) | INPUT VIA CT e nang le tlhahiso ea bobeli ea 5A - Moroalo: <0.2VA, Ho mamella ho fetella: 20A RMS e tsoelang pele, 300A RMS bakeng sa metsotsoana ea 0.5. | |
| /1A(2A) | INPUT VIA CT e nang le tlhahiso ea bobeli ea 1A - Moroalo: <0.05VA, Ho mamella ho fetella: 3A RMS e tsoelang pele, 80A RMS bakeng sa metsotsoana ea 0.5. | ||
| 50A(100A) | INPUT VIA CT e nang le 50A ka ho toba - Moroalo: <0.05VA, Boima bo feteletseng: 120A RMS e tsoelang pele, 2000A RMS bakeng sa metsotsoana ea 0.5. | ||
| 40mA: (ka boikhethelo) | INPUT VIA CT e nang le tlhahiso ea bobeli ea 40mA, e sebelisa CT ea kantle - Split Core CT kapa Solid Core CT - tekanyo ea mantlha ea 100-1200A | ||
| Li-terminals tsa hona joale tsa ho kenya | 3 x Boholo ba karolo ea terata: 16 mm² | ||
| Boema-kepe ba puisano COM1 | EIA RS-485 e tloaelehileng | Optically thoko, max. lebelo 115.2Kb/s | |
| COM1 li-terminals | 3 x Boholo ba karolo ea terata: 2.5 mm² | ||
| Boema-kepe ba puisano COM3 | Boema-kepe ba IR COM | Infra Red, max. lebelo 38.4Kb/s | |
| Phepelo ea Matla (e arotsoe ka Galvanically) | 40-300V AC/DC (e tloaelehileng) | 50/60 Hz - 9VA | |
| Li-terminals tsa ho kenya motlakase | 3 x Boholo ba karolo ea terata: 2.5 mm² | ||
| MODULE 2DI/ETSA | DIGITAL INPUT x 2 tse arotsoeng ka mahlo | Ho omella, ho kolobisoa ka hare @ 5VDC | |
| SEHLAHLWA SA DIGITAL x 1 | 0.15A/250 VAC - 400 VDC, lebitso le le leng (SPST Form A) | ||
| 2DI / DO li-terminals | 5 x Boholo ba karolo ea terata: 2.5 mm² | ||
| MODULE 4DI/2DO
(Taba ea boikhethelo) |
DIGITAL INPUT x 2 tse arotsoeng ka mahlo | Ho omella, ho kolobisoa ka hare @ 24VDC | |
| SEHLAHLWA SA DIGITAL x 2 | EMR | 5A/250 VAC; 5A/30 VDC, lebitso le le leng (SPST Form A) | |
| SSR | 0.15A/250 VAC - 400 VDC, lebitso le le leng (SPST Form A) | ||
| Li-terminals tsa 4DI/2DO | 9 x Boholo ba karolo ea terata: 2.5 mm² | ||
| MODULE 4 AO (Taba ea boikhethelo) | ANALOG OUT x Liphetho tse 4 tse ikhethileng (likhetho tse 4 tse fapaneng) | ±1 mA, mojaro o moholo ke 5 kW (100% e imetsoe) | |
| 0-20 mA, boholo ba mojaro 510 W | |||
| 4-20 mA, boholo ba mojaro 510 W | |||
| 0-1 mA, mojaro o moholo ke 5 k W (100% e tletse) | |||
| 4 AO terminals | 5 x Boholo ba karolo ea terata: 2.5 mm² | ||
| Boema-kepe ba puisano COM2 (Ha u rata) | Ethernet | 10/100 Base T, lebelo la ho ikamahanya le maemo, Max. lebelo 100Mb/s | |
| Sehokelo sa ETH | Cable e sirelelitsoeng ea RJ45 | ||
| Boema-kepe ba puisano COM2 (Boikhethelo) | Profibus | Max. lebelo 12 Mb/s | |
| Li-terminals tsa Profibus | 5 x Karolo e kholo ea terata: 2.5 mm2 (12 AWG) kapa ho sebelisa terminal ho DB9 converter: P/N AC0153 REV.A2 | ||
| Boema-kepe ba puisano COM2 (Boikhethelo) | EIA RS-232-422/485 e tloaelehileng | Optically thoko, max. lebelo 115.2Kb/s – ho hokelwa ho modem ya GPRS ha e otara | |
| COM2 li-terminals | 5 x Boholo ba karolo ea terata: 2.5 mm² Le sehokelo sa DB9 | ||
BG0504 REV.A3
Litokomane / Lisebelisoa
 |
SATEC EM132 Multi Function Meter [pdf] Bukana ea Mosebelisi EM132 Multi Function Meter, EM132, Multi Function Meter, Meter ea Mosebetsi, Metha |