DVP-SV2
Leqephe la Litaelo
Compact, Multi-Functional, Litaelo tse ngata
DVP-0290030-01
20230316
Kea leboha ha u khethile Delta DVP-SV2. SV2 ke lintlha tse 28 (lintlha tse 16 + liphetho tse 12)/24-point (litlhahiso tse 10 + liphetho tse 12 + liteishene tse 2 tsa analog) PLC MPU, e fanang ka litaelo tse fapaneng le mohopolo oa 30k oa lenaneo, o khona ho hokela mefuta eohle ea Slim.
letoto la mehlala ea katoloso, ho kenyeletsoa dijithale I/O (max. 512 lintlha), li-module tsa analoge (bakeng sa A/D, D/A phetoho le tekanyo ea mocheso) le mefuta eohle ea li-module tsa katoloso ea lebelo le holimo. Lihlopha tse 4 tsa phallo ea lebelo le holimo (200 kHz) (le lilepe tse peli tse hlahisang 10 kHz ho 24SV2) le litaelo tse 2 tsa li-axis tse peli li khotsofatsa mefuta eohle ea ts'ebeliso. DVP-SV2 e nyane ka boholo mme ho bonolo ho e kenya.
DVP-SV2 ke sesebelisoa sa OPEN-TYPE. E lokela ho kenngoa ka k'haboteng ea taolo e se nang lerōle le tsamaisoang ke moea, mongobo, ts'oaetso ea motlakase le ho thothomela. Ho thibela basebetsi bao e seng ba tlhokomelo ho sebetsa DVP-SV2, kapa ho thibela kotsi ho senya DVP-SV2, khabinete ea taolo eo ho eona DVP-SV2 e kentsoeng e lokela ho hlomelloa ka tšireletso. Bakeng sa mohlalaample, khabinete ea taolo eo ho eona DVP-SV2 e kentsoeng e ka notleloa ka sesebelisoa kapa senotlolo se khethehileng.
U SE KE UA hokela motlakase oa AC ho litheminale life kapa life tsa I/O, ho seng joalo tšenyo e kholo e ka hlaha. Ka kopo, sheba lithapo tsohle hape pele DVP-SV2 e ka tsamaisoa. Kamora hore DVP-SV2 e khaotsoe, U SE KE UA ama li-terminals ka motsotso. Etsa bonnete ba hore terminal ea fatše
ho DVP-SV2 e thehiloe ka nepo molemong oa ho thibela tšitiso ea motlakase.
Sehlahisoa Profile
Litlhaloso tsa Motlakase
| Mohlala (mohlala) /Item | Tlhaloso: DVP28SV11R2 | DVP24SV11T2 DVP28SV11T2 | DVP28SV11S2 |
| Phepelo ea motlakase voltage | 24VDC (-15% ~ 20%) (e nang le tšireletso ea counter-connection ho polarity ea matla a kenyang a DC) | ||
| Inrush current | Max. 2.2A@24VDC | ||
| Matla a fuse | 2.5A/30VDC, Polyswitch | ||
| Tšebeliso ea matla | 6W | ||
| Insulation resistance | > 5MΩ (kaofela I/O ntlha-ho ea fatše: 500VDC) | ||
|
Ho itšireletsa mafung |
ESD (IEC 61131-2, IEC 61000-4-2): 8kV Air Discharge
EFT (IEC 61131-2, IEC 61000-4-4): Mohala oa Matla: 2kV, Digital I/O: 1kV, Analog & Communication I/O: 1kV Damped-Oscillatory Wave: Mohala oa Matla: 1kV, Digital I/O: 1kV RS (IEC 61131-2, IEC 61000-4-3): 26MHz ~ 1GHz, 10V/m Surge (IEC 61131-2, IEC 61000-4-5 XNUMX) : thapo ea motlakase ea DC: mokhoa o fapaneng ± 0.5 kV |
||
|
Ho thethefatsa |
Bophara ba terata ea fatše ha boa lokela ho ba tlase ho feta ea wiring
terminal ea matla. (Ha li-PLC li sebelisoa ka nako e le 'ngoe, ka kopo etsa bonnete ba hore PLC e ngoe le e ngoe e thehiloe hantle.) |
||
| Tshebetso / polokelo | Tshebetso: 0ºC ~ 55ºC (mocheso); 5 ~ 95% (mongobo); tekanyo ea tšilafalo 2
Polokelo: -25ºC ~ 70ºC (mocheso); 5 ~ 95% (mongobo) |
||
|
Litumello tsa setsi |
UL508
European community EMC Directive 89/336/EEC le Low Voltage Taelo ea 73/23/EEC |
||
| Tšisinyeho (//) /shock immune immune | Maemo a machaba: IEC61131-2, IEC 68-2-6 (TEST Fc)/IEC61131-2 & IEC 68-2-27 (TEST Ea) | ||
| Boima ba 'mele (g) | 260 | 240 | 230 |
| Ntlha ea ho Kena | |||
| Spec. /Lintho | 24VDC kenyeletso e le 'ngoe e tloaelehileng ea koung | ||
| 200kHz | 10kHz | ||
| Kenyelletso No. | X0, X1, X4, X5, X10, X11, X14, X15#1 | X2, X3, X6, X7, X12, X13, X16, X17 | |
| Keletso voltage (±10%) | 24VDC, 5mA | ||
| Kenyelletso ea ho kenya | 3.3kΩ | 4.7kΩ | |
| Boemo ba ts'ebetso | E tima⭢Bula | 5mA (16.5V) | 4mA (16.5V) |
| Ho ⭢E tima | <2.2mA (8V) | <1.5mA (8V) | |
| Nako ea ho arabela | E tima⭢Bula | <150ns | <8μs |
| Ho ⭢E tima | <3μs | <60μs | |
| Sefe nako | E ka feto-fetoha ka hare ho 10 ~ 60ms ka D1020, D1021 (Default: 10ms) | ||
Hlokomela: 24SV2 ha e tšehetse X12~X17.
#1: Bakeng sa lihlahisoa tse nang le mofuta oa hardware hamorao ho feta A2, lisebelisoa tsa X10, X11, X14, X15 li lokela ho sebelisoa ka sekhahla sa 200kHz. Mofuta oa firmware + hardware o ka fumanoa leiboleng ea setikara sa sehlahisoa, mohlala, V2.00A2.
| Ntlha ea Sephetho | ||||
| Spec. /Lintho | Relay | Transistor | ||
| Lebelo le phahameng | Lebelo le tlase | |||
| Sephetho No. | Y0 ~ Y7, Y10 ~ Y13 | Y0 ~Y4, Y6 | Y5, Y7, Y10 ~ Y13 | |
| Max. makhetlo a mangata | 1Hz | 200kHz | 10kHz | |
| Sebetsa voltage | 250VAC, <30VDC | 5 ~ 30VDC #1 | ||
| Max. morwalo | E hanyetsanang | 1.5A/1 ntlha (5A/COM) | 0.3A/1 ntlha @ 40˚C | |
|
Max. morwalo |
E susumetsang | #2 | 9W (30VDC) | |
| Lamp | 20WDC/100WAC | 1.5W (30VDC) | ||
| Nako ea ho arabela | E tima⭢Bula |
Hoo e ka bang. 10ms |
0.2μs | 20μs |
| Ho ⭢E tima | 0.2μs | 30μs | ||
#1: Bakeng sa mohlala oa tlhahiso ea PNP, UP le ZP li tlameha ho hokeloa ho matla a 24VDC (-15% ~ +20%). Tšebeliso e lekantsoeng ke 10mA/point.
#2: Litšiea tsa bophelo 
| Litlhaloso tsa lisebelisoa tsa analog (E sebetsa feela ho DVP24SV11T2) | ||
| Moqtagkenya | Kenyelletso ea hajoale | |
| Lenane la tlhahiso ea analog | 0 ~ 10V | 0 ~ 20mA |
| Dijithale ho fetolela | 0 ~ 4,000 | 0 ~ 2,000 |
| Qeto | 12-bit (2.5mV) | 11-bit (10uA) |
| Kenyelletso ea ho kenya | > 1MΩ | 250Ω |
| Ho nepahala ka kakaretso | ± 1% ea tekanyo e felletseng ka har'a mefuta e fapaneng ea mocheso oa ts'ebetso ea PLC | |
| Nako ea ho arabela | 2ms (E ka hlophisoa ka D1118.) #1 | |
| Boemo bo felletseng ba ho kenya | ± 15V | ± 32mA |
| Sebopeho sa data ea dijithale | Tlatsetso ea 16-bit 2 (12
lintlha tsa bohlokoa) |
Tlatsetso ea 16-bit 2 (11
lintlha tsa bohlokoa) |
| Karolelano ea mosebetsi | E fanoe (E ka behoa ka D1062) #2 | |
| Mokhoa oa ho itšehla thajana | Ha ho khethollo pakeng tsa li-circuits tsa digital le li-circuits tsa analog | |
#1: Haeba potoloho ea scan ninete ho feta 2 milliseconds kapa e kholo ho feta boleng ba ho seta, potoloho ea scan e fuoa khetho.
#2: Haeba boleng ba D1062 ke 1, boleng ba hona joale boa baloa.
I/O Configuration
| Mohlala | Matla | Kenyeletso | Sephetho | Tlhophiso ea I/O | |||||
| Ntlha | Mofuta | Ntlha | Mofuta | Relay | Transistor (NPN) | Transistor (PNP) | |||
| 28 SV | 24SV2 | ||||||||
| Tlhaloso: DVP28SV11R2 | 24 VDC |
16 | DC (S ho k Kapa Mohloli) |
12 | Relay |  |
 |
 |
 |
| Tlhaloso: DVP28SV11T2 | 16 | 12 | Transistor (NPN) |
||||||
| Tlhaloso: DVP24SV11T2 | 10 | 12 | |||||||
| DVP28SV11S2 | 16 | 12 | Transistor (PNP) |
||||||
Ho kenya
Ka kopo kenya PLC sebakeng se kampetsoeng se nang le sebaka se lekaneng ho e potoloha ho lumella ho qhalana ha mocheso. Bona [Setšoantšo sa 5].
- Ho phahamisa ka ho Otloloha: Sebelisa screw ea M4 ho latela boholo ba sehlahisoa.
- DIN Rail Mounting: Ha o kenya PLC ho 35mm DIN seporo, etsa bonnete ba hore o sebelisa sekotwana se bolokang ho emisa motsamao o mong le o mong oa PLC le ho fokotsa monyetla oa hore lithapo li lokolohe. Sekotwana se bolokang se ka tlase ho PLC. Ho boloka PLC ho
DIN seporo, theola sekotwana, se behe holim'a seporo ebe u se sutumelletsa holimo ka bonolo. Ho tlosa PLC, hula sekotwana sa ho boloka fatše ka screwdriver e bataletseng 'me ka bonolo u tlose PLC ho tloha seporong sa DIN. Bona [Setšoantšo sa 6].
Wiring
- Sebelisa 26-16AWG (0.4~1.2mm) terata e le 'ngoe kapa tse ngata tsa mantlha ho litheminale tsa lithapo tsa I/O. Sheba setšoantšo se letsohong le letona bakeng sa litlhaloso tsa sona. Li-screws tsa terminal tsa PLC li lokela ho tiisetsoa ho 2.00kg-cm (1.77 in-lbs) 'me ka kopo sebelisa 60/75ºC feela ea koporo.
- U SE KE UA terata terminal e se nang letho. U SE KE UA beha thapo ea lets'oao la I/O sebakeng se tšoanang sa lithapo.
- U SE KE UA lihela conductor e nyane ea tšepe ho PLC ha u ntse u fafatsa le ho thapo. Taola setikara se lesobeng la ho qhala mocheso bakeng sa ho thibela lintho tse tsoang linaheng tse ling hore li se ke tsa oela, ho etsa bonnete ba hore PLC e fela mocheso o tloaelehileng.
Phepelo ea motlakase
Matla a kenyang DVP-SV2 ke DC. Ha o sebelisa DVP-SV2, hlokomela lintlha tse latelang:
- Matla a hokahane le li-terminals tse peli, 24VDC le 0V, 'me boholo ba matla ke 20.4 ~ 28.8VDC. Haeba matla voltage ka tlase ho 20.4VDC, PLC e tla khaotsa ho sebetsa, lihlahisoa tsohle li ea "Off", 'me letšoao la ERROR LED le tla qala ho panya ho sa khaotse.
- Ho tima matla ka tlase ho 10ms ho ke ke ha ama ts'ebetso ea PLC. Leha ho le joalo, nako ea ho koala e telele haholo kapa ho theoha ha matlatage tla emisa ts'ebetso ea PLC, 'me liphetho tsohle li tla tima. Ha matla a khutlela ho tloaelehileng
boemo, PLC e tla qala ts'ebetso ka bo eona. (Ka kopo hlokomela li-relay le li-relays tse thusang ka hare ho PLC ha u etsa lenaneo).
Safety Wiring
Kaha DVP-SV2 e sebetsa feela le phepelo ea motlakase ea DC, li-module tsa phepelo ea motlakase tsa Delta (DVPPS01/DVPPS02) ke lisebelisoa tse loketseng tsa motlakase bakeng sa DVP-SV2. Re fana ka tlhahiso ea hore u kenye potoloho ea tšireletso setsing sa phepelo ea motlakase ho sireletsa DVPPS01 kapa
DVPPS02. Sheba setšoantšo se ka tlase.
- Phepelo ea matla a AC: 100 ~ 240VAC, 50/60Hz
- Seqhenqha
- Emergency stop: Konopo ena e khaola phepelo ea motlakase ea sistimi ha tšohanyetso e etsahala.
- Letšoao la matla
- Matla a phepelo ea matla a AC
- Fuse ea tšireletso ea phepelo ea motlakase (2A)
- DVPPS01/DVPPS02
- Matla a phepelo ea matla a DC: 24VDC, 500mA
- DVP-PLC (yuniti e kholo ea ho sebetsa)
- Digital I/O module
Mohala oa ho Kena
Ho na le mefuta e 2 ea lisebelisoa tsa DC, SINK le SOURCE. (Sheba mohlalaample ka tlase. Bakeng sa tlhophiso e felletseng ea lintlha, ka kopo sheba litlhaloso tsa mofuta o mong le o mong.)
DC Signal IN - mokhoa oa MOHLOLI
Input point lupu e lekanang le potoloho 
DC Signal IN – SINK mode
Input point lupu e lekanang le potoloho
Wiring ea Output Point
- DVP-SV2 e na le li-module tse peli tsa tlhahiso, relay le transistor. Ela hloko khokahanyo ea li-terminals tse arolelanoang ha li-terminals tsa wiring output.
- Li-terminals tsa lihlahisoa, Y0, Y1, le Y2, tsa mefuta ea li-relay li sebelisa C0 e tloaelehileng port; Y3, Y4, le Y5 sebelisa C1 tloaelehileng koung; Y6, Y7, le Y10 sebelisa C2 tloaelehileng koung; Y11, Y12, le Y13 li sebelisa boema-kepe bo tloaelehileng ba C3. Bona [Setšoantšo sa 10].
Ha lintlha tsa tlhahiso li nolofalitsoe, matšoao a tsona a lumellanang le phanele e ka pele e tla ba teng. - Li-terminals tsa Y0 le Y1 tsa mohlala oa transistor (NPN) li hokahane le li-terminals tse tloaelehileng C0. Y2 le Y3 li hokahane le terminal e tloaelehileng ea C1. Y4 le Y5 li hokahane le terminal e tloaelehileng ea C2. Y6 le Y7 li hokahane le
terminal e tloaelehileng C3. Y10, Y11, Y12, le Y13 li hokahane le terminal e tloaelehileng ea C4. Sheba [Setšoantšo sa 11a]. Li-terminals tsa Y0~Y7 mofuteng oa transistor (PNP) li hokahane le li-terminals tse tloaelehileng UP0 le ZP0. Y10~Y13 e hokahane le li-terminals tse tloaelehileng tsa UP1 le ZP1. Sheba [Setšoantšo sa 11b].
- Isolation circuit: Optical coupler e sebelisetsoa ho arola matšoao pakeng tsa potoloho ka hare ho PLC le li-module tsa ho kenya.
Relay (R) terata ea potoloho e hlahisoang 
- Phepelo ea motlakase ea DC
- Emergency stop: E sebelisa switch ea kantle
- Fuse: E sebelisa 5 ~ 10A fuse sebakeng se arolelanoang sa mabitso a tsoang ho sireletsa potoloho ea tlhahiso
- Nakoana voltage suppressor (SB360 3A 60V): E eketsa nako ea bophelo ea ho kopana.
1. Khatello ea diode ea mojaro oa DC: E sebelisoa ha e le matla a manyenyane [Setšoantšo sa 13] 2. Khatello ea Diode + Zener ea mojaro oa DC: E sebelisoa ha e le matla a maholo le hangata On / Off [Setšoantšo sa 14] - Lebone la incandescent (moroalo o hanyetsanang)
- Phepelo ea motlakase ea AC
- Tlhahiso e ikhethileng ka letsoho: Bakeng sa mohlalaample, Y3 le Y4 li laola ho matha pele le ho khutlela morao ha enjene, ho etsa sehokelo bakeng sa potoloho ea kantle, hammoho le lenaneo la kahare la PLC, ho netefatsa ts'ireletso e bolokehileng haeba ho ka ba le liphoso tse sa lebelloang.
- Letšoao la Neon
- Absorber: E fokotsa tšitiso ho mojaro oa AC [Setšoantšo sa 15]
Transistor output circuit wiring 
- Phepelo ea motlakase ea DC
- Emergency stop
- Fuse ea tšireletso ea potoloho
- Sephetho sa mohlala oa transistor ke "mokelli ea bulehileng". Haeba Y0/Y1 e behiloe ho pulse output, tlhahiso ea hona joale e tlameha ho ba kholo ho feta 0.1A ho netefatsa ts'ebetso e tloaelehileng ea mohlala.
1. Khatello ea diode: E sebelisoa ha e le matla a manyenyane [Setšoantšo sa 19] le [Setšoantšo sa 20] 2. Khatello ea Diode + Zener: E sebelisoa ha e le matla a maholo le khafetsa On/Off [Setšoantšo sa 21] [Setšoantšo sa 22] - Tlhahiso e ikhethileng ka letsoho: Bakeng sa mohlalaample, Y2 le Y3 li laola ho matha pele le ho khutlela morao ha enjene, ho etsa sehokelo bakeng sa potoloho ea kantle, hammoho le lenaneo la kahare la PLC, ho netefatsa ts'ireletso e bolokehileng haeba ho ka ba le liphoso tse sa lebelloang.
Wiring ea Kantle ea A/D (Bakeng sa DVP24SV11T2 Feela) 
BAT.LOW LED Indicator
Ka mor'a hore matla a 24 V DC a tima, lintlha tse sebakeng sa marang-rang li tla bolokoa mohopolong oa SRAM, 'me betri e ka nchafatsoang e tla fana ka matla mohopolong oa SRAM.
Ka hona, haeba betri e senyehile kapa e ke ke ea lefisoa, data e lenaneong le sebaka sa marang-rang se tla lahleha. Haeba o hloka ho boloka data ka ho sa feleng lenaneong le ngoliso ea data e latched, ka kopo sheba mokhoa oa ho boloka data ho Flash.
ROM ka ho sa feleng le mokhoa oa ho khutlisetsa data ho Flash ROM e boletsoeng ka tlase.
Mokhoa oa ho boloka data ho Flash ROM ka ho sa feleng:
U ka sebelisa WPLSoft (Options -> PLC<=>Flash) ho bonts'a hore na u boloke data ka ho sa feleng sebakeng se lachetsoeng mohopolong oa Flash ROM (data e ncha e bonts'itsoeng e tla nkela data eohle e bolokiloeng mohopolong).
Mokhoa oa ho khutlisa data ho Flash ROM:
Haeba betri e ka tjhajwang e le matla a tlasetage, ho fella ka tahlehelo e ka bang teng ea data lenaneong, PLC e tla khutlisetsa data sebakeng se lachetsoeng lenaneong le sesebelisoa sa D sa Flash ROM mohopolong oa SRAM (M1176 = On) nakong e tlang ha DC24V e tla.
matlafatsoa bocha. ERROR LED flashing e tla u hopotsa hore haeba lenaneo le rekotiloeng le khona ho tsosolosa ts'ebetsong ea lona. U hloka feela ho koala le ho matlafatsa PLC hang ho qala ts'ebetso ea eona (RUN).
- Betri ea lithium-ion e ka nchafatsoang ho DVP-SV2 e sebelisoa haholo ts'ebetsong ea latched le polokelo ea data.
- Betri ea lithium-ion e qositsoe ka botlalo fekthering 'me e khona ho boloka ts'ebetso ea latched le polokelo ea data bakeng sa likhoeli tse 6. Haeba DVP-SV2 e sa sebetse ka nako e ka tlase ho likhoeli tse 3, bophelo ba betri ha bo fokotsehe. Ho thibela motlakase o hlahisoang ke betri hore o se ke oa fella ka bophelo bo khutšoanyane ba betri, pele o khaola DVP-SV2 nako e telele, o hloka ho matlafatsa DVP-SV2 lihora tse 24 ho tjhaja betri.
- Haeba betri ea lithium-ion e behiloe sebakeng seo mocheso o leng ka holimo ho 40 C, kapa haeba e lefisoa ka makhetlo a fetang 1000, phello ea eona e ba mpe, 'me nako eo data e ka bolokoang ka eona e ka tlaase ho 6. tšoele.
- Betri ea lithium-ion e ka chacha, 'me e phela nako e telele ho feta betri e tloaelehileng. Leha ho le joalo, e ntse e na le potoloho ea eona ea bophelo. Ha matla a betri a sa lekana ho boloka data sebakeng sa marang-rang, ka kopo e romelle ho mofani oa thepa hore a lokisoe.
- Ka kopo hlokomela letsatsi la tlhahiso. Betri e chariloeng e ka tšoarella likhoeli tse 6 ho tloha ka letsatsi la ho hlahisoa ha eona. Haeba u fumana hore BAT.LOW indicator e lula e le teng ka mor'a hore PLC e kenngoe motlakase, ho bolela hore matla a betritage tlase mme betri e ntse e tjhajwa. DVP-SV2 e tlameha ho sebetsa lihora tse fetang 24 ho tjhaja betri ka botlalo. Haeba letšoao le fetoha ho tloha ho "flash" (motsotsoana o mong le o mong o le mong), ho bolela hore betri ha e sa tla hlola e tjhaja. Ka kopo sebetsa data ea hau hantle ka nako 'me u romele PLC ho mofani oa thepa hore e lokisoe.
Ho nepahala (ea bobeli/khoeli) ea RTC
| Mocheso (ºC/ºF) | 0/32 | 25/77 | 55/131 |
| Max. ho se nepahale (ea bobeli) | -117 | 52 | -132 |
Litokomane / Lisebelisoa
 |
DELTA DVP-SV2 Mananeo a Lokisitsoeng a Logic [pdf] Buka ea Taelo DVP-SV2 Programmable Logic Controllers, DVP-SV2, Programmable Logic Controllers, Logic Controllers, Controllers |