Arduino ABX00069 Nano 33 BLE Sense Rev2 3.3V AI e Nobled Board
Likaroloana
- NINA B306 Module
- processor
- 64 MHz Arm® Cortex®-M4F (ka FPU)
- 1 MB Flash + 256 kB RAM
- Bluetooth® 5 radio multiprotocol
- 2 Mbps
- CSA #2
- Advertising Extensions
- Nako e telele
- +8 dBm TX matla
- -95 dBm kutloisiso
- 4.8 mA ho TX (0 dBm)
- 4.6 mA ho RX (1 Mbps)
- Balun e kopantsoeng e nang le 50 Ω e phethiloeng e le 'ngoe
- IEEE 802.15.4 tšehetso ea seea-le-moea
- Khoele
- Zigbee
- Pheripherals
- Lebelo le felletseng la 12 Mbps USB
- NFC-A tag
- Setsi sa ts'ireletso sa Arm CryptoCell CC310
- QSPI/SPI/TWI/I²S/PDM/QDEC
- Lebelo le phahameng 32 MHz SPI
- Quad SPI interface 32 MHz
- EasyDMA bakeng sa lihokelo tsohle tsa dijithale
- 12-bit 200 ksps ADC
- 128 bit AES/ECB/CCM/AAR co-processor
- BMI270 6-axis IMU (Accelerometer le Gyroscope) 16-bit
- 3-axis accelerometer e nang le ±2g/±4g/±8g/±16g range
- 3-axis gyroscope e nang le ±125dps/±250dps/±500dps/±1000dps/±2000dps range
- BMM150 3-axis IMU (Magnetometer)
- 3-axis digital geomagnetic sensor
- 0.3μT qeto
- ±1300μT (x,y-axis), ±2500μT (z-axis)
- LPS22HB (Barometer le sensor ea mocheso)
- 260 ho isa ho 1260 hPa khatello e felletseng ea khatello e nang le 24-bit e nepahetseng
- Bokhoni bo phahameng ba khatello ea maikutlo: 20x e felletseng
- Matšeliso a mocheso a kentsoeng
- Tlhahiso ea data ea 16-bit ea mocheso
- 1 Hz ho isa ho 75 Hz sekgahla sa data se sitisa mesebetsi: Data Ready, lifolakha tsa FIFO, menyako ea khatello
- HS3003 Sensor ea mocheso le mongobo
- 0-100% mefuta e fapaneng ea mongobo
- Ho nepahala ha mongobo: ± 1.5%RH, e tloaelehileng (HS3001, 10 ho isa ho 90%RH,25°C)
- Ho nepahala ha sensor ea mocheso: ± 0.1 ° C, e tloaelehileng
- Ho fihlela ho 14-bit mongobo le data e hlahisoang ke mocheso
- APDS-9960 (Bohaufi ba dijithale, Leseli la Ambient, RGB le Sensor ea Boitšisinyo)
- Ambient Light le RGB Color Sensing e nang le lifilthara tse thibelang tsa UV le IR
- Kutlo e phahameng haholo - E loketse ts'ebetso ka mor'a khalase e lefifi
- Proximity Sensing le Ambient Light Rejection
- Ho Utloisisa Boitšisinyo bo Ratang
- Setšoantšo sa MP34DT06JTR (Maekerofounu ea Dijithale)
- AOP = 122.5 dbSPL
- 64 dB karo-karolelano ea lerata-ho-lerata
- Omnidirectional sensitivity
- -26 dBFS ± 3 dB kutlo
- MP2322 DC-DC
- E laola tlhahiso ea molumotage ho tloha ho 21V ka bonyane ba 65% e sebetsang hantle @ @minimum load
- Ho feta 85% e sebetsang hantle @12V
- processor
LIHLAHISO TSEBISO
Boto
Joalo ka liboto tsohle tsa Nano form factor, Nano 33 BLE Sense Rev2 ha e na tjhaja ea betri empa e ka tsamaisoa ka USB kapa lihlooho.
HLOKOMELA: Nano 33 BLE Sense Rev2 e ts'ehetsa 3.3VI/Os feela 'me HA E mamelle 5V kahoo ka kopo etsa bonnete ba hore ha o hokelle matšoao a 5V ka kotloloho ho boto ena kapa e tla senyeha. Hape, ho fapana le liboto tsa Arduino Nano tse tšehetsang ts'ebetso ea 5V, pinana ea 5V HA E fane ka vol.tage empa ho e-na le hoo e hokahane, ka jumper, ho kenya matla a USB.
Lintlha
Maemo a Tšebetso a khothalelitsoeng
| Letšoao | Tlhaloso | Min | Max |
| Meeli ea mocheso oa Conservative bakeng sa boto kaofela: | -40 °C (40 °F) | 85°C ( 185 °F) |
Tšebeliso ea Matla
| Letšoao | Tlhaloso | Min | Tlanya | Max | Yuniti |
| PBL | Tšebeliso ea matla e nang le loop e phathahaneng | TBC | mW | ||
| PLP | Tšebeliso ea matla ka mokhoa o fokolang oa matla | TBC | mW | ||
| PMAX | Tšebeliso e Felletseng ea Matla | TBC | mW |
E sebetsa hapeview
Board Topology
Holimo:
Topology ea boto
| Ref. | Tlhaloso | Ref. | Tlhaloso |
| U1 | NINA-B306 Mojule Bluetooth® Low Energy 5.0 Mojule | U6 | MP2322GQH Step Down Converter |
| U2 | BMI270 Sensor IMU | PB1 | IT-1185AP1C-160G-GTR Konopo ea ho sututsa |
| U3 | Maekerofounu ea MP34DT06JTR MEMS | U8 | HS3003 Mongobo oa Sensor |
| U7 | Tlhaloso: BMM150 Magnetometer IC | DL1 | Led L |
| U5 | APDS-9660 Ambient Module | DL2 | Matla a Led |
| U9 | LPS22HBTR Sensor sa Khatello ea IC |
Tlase:
| Ref. | Tlhaloso | Ref. | Tlhaloso |
| SJ1 | VUSB jumper | SJ2 | D7 Jumper |
| SJ3 | 3v3 Jumper | SJ4 | D8 Jumper |
processor
Main Processor ke Arm® Cortex®-M4F e sebetsang ho fihla ho 64MHz. Boholo ba lithakhisa tsa eona li hokahane le lihlooho tsa ka ntle, leha ho le joalo tse ling li boloketsoe puisano ea ka hare le mochine o se nang mohala le li-peripherals tsa I2C tse ka hare (IMU le Crypto).
HLOKOMELA: Ho fapana le liboto tse ling tsa Arduino Nano, li-pins A4 le A5 li na le ho hula ka hare le ho sebelisoa e le I2C Bus kahoo ha ho khothalletsoe ho sebelisoa e le lisebelisoa tsa analog.
IMU
Nano 33 BLE Sense Rev2 e fana ka bokhoni ba IMU ka 9-axis, ka ho kopanya BMI270 le BMM150 ICs. BMI270 e kenyelletsa li-axis gyroscope tse tharo hammoho le accelerometer tse tharo, ha BMM150 e khona ho utloa phapang ea masimo a khoheli ka litekanyo tsohle tse tharo. Lintlha tse fumanoeng li ka sebelisoa bakeng sa ho lekanya mekhahlelo e tala ea motsamao hammoho le ho ithuta ka mochini.
LPS22HB (U9) Barometer le Sensor ea Mocheso
LPS22HB khatello ea maikutlo IC (U9) e kenyelletsa sensor ea khatello e felletseng ea piezoresistive hammoho le sensor ea mocheso e kopantsoeng le chip e nyane. Sensor ea khatello (U9) e kopana le microcontroller e kholo (U1) ka sebopeho sa I2C. Karolo ea kutlo e entsoe ka lesela le emisitsoeng le emisitsoeng ka micromachine bakeng sa ho lekanya khatello e felletseng, 'me e kenyelletsa borokho ba Wheatstone ka hare bakeng sa ho metha likarolo tsa piezoresistive. Likhatello tsa mocheso li lefshoa ka sensor e kenyellelitsoeng ea mocheso on-chip. Khatello e felletseng e ka tloha ho 260 ho isa ho 1260 hPa. Lintlha tsa khatello li ka hlahlojoa ka I2C ho fihla ho li-bits tse 24, ha data ea mocheso e ka hlahlojoa ho fihlela ho 16-bits. Laeborari ea Arduino_LPS22HB e fana ka ts'ebetsong e seng e loketse ho sebelisoa ea protocol ea I2C ka chip ena.
HS3003 (U8) Mongobo o Batlang le Mocheso oa Sensora
HS3003 (U8) ke li-sensor tsa MEMS, tse etselitsoeng ho fana ka lipalo tse nepahetseng tsa mongobo le mocheso ka har'a sephutheloana se senyenyane. Mocheso-matšeliso le calibration e etsoa ka-chip, ntle le ho hloka potoloho e ka ntle. HS3003 e ka lekanya mongobo o lekanyelitsoeng ho tloha ho 0% ho isa ho 100%RH ka linako tsa karabo e potlakileng (tlas'a metsotsoana e 4). Sensor e kenyellelitsoeng ea mocheso oa on-chip (e sebelisetsoang matšeliso) e na le ho nepahala ha mocheso oa ± 0.1 °C. U8 e buisana ka microcontroller e kholo ka bese ea I2C.
Ho lemoha ka boitšisinyo
Ho lemoha ka boitšisinyo ho sebelisa li-photodiode tse 'nè tsa nqa e le 'ngoe ho utloa matla a IR (a tsoang ho LED e kopantsoeng) ho fetolela tlhahisoleseding ea 'mele (e leng lebelo, sebaka le sebaka) hore e be boitsebiso ba digital. Moralo oa enjene ea boitšisinyo e na le ts'ebetso ea othomathike (e ipapisitseng le liphetho tsa enjine ea Proximity), ho tlosa leseli le haufi, ho hlakoloa ha lipuo tse fapaneng, li-converter tsa data tse peli tsa 8-bit, ho lieha ho boloka matla, FIFO ea 32-dataset, le puisano e khannoang ke I2C. Enjene ea boitšisinyo e fana ka mefuta e mengata e fapaneng ea litlhoko tsa boitšisinyo ba sesebelisoa sa mohala: boitšisinyo bo bonolo ba HO PHAHAMA-RARIGHT-LE-LETELE kapa boitšisinyo bo rarahaneng ho feta bo ka utluoa ka nepo. Tšebeliso ea matla le lerata li fokotsehile ka nako e feto-fetohang ea IR LED.
Ho lemoha ha haufi
Karolo ea ho lemoha ha Proximity e fana ka tekanyo ea sebaka (Mohlala, skrine ea sesebelisoa sa mohala tsebeng ea mosebedisi) ka ho lemoha photodiode ea matla a IR a bonts'itsoeng (a tsoang ho LED e kopantsoeng). Liketsahalo tsa ho bona/tokolla li khannoa, 'me li etsahala neng kapa neng ha sephetho sa haufi se tšela litlhophiso tse kaholimo le/kapa tse tlase. Enjene ea proximity e na le lirejistara tsa tokiso ea offset ho lefella offset ea sistimi e bakoang ke li-reflections tse sa batleheng tsa IR tse hlahang ho sensor. Matla a IR LED ke fektheri e lokisitsoeng ho felisa tlhoko ea ho lekanya lisebelisoa tsa ho qetela ka lebaka la ho fapana ha likarolo. Liphetho tsa haufi li ntlafatsoa hape ka ho tlosa mabone a ambient ka tsela e iketsang.
Ho lemoha 'Mala le ALS
Karolo ea ho lemoha Mebala le ALS e fana ka lintlha tse khubelu, tse tala, tse putsoa le tse hlakileng. E 'ngoe le e 'ngoe ea likanale tsa R, G, B, C e na le sefe e thibelang UV le IR le sesebelisoa sa data se inehetseng se hlahisang data ea 16-bit ka nako e le 'ngoe. Meaho ena e lumella lits'ebetso ho lekanya khanya le 'mala oa kutlo ka nepo, e lumellang lisebelisoa ho bala mocheso oa mebala le ho laola khanya ea morao.
Microphone ea Digital
MP34DT06JTR ke maekerofounu ea ultra-compact, e tlase, e matla hohle, ea dijithale ea MEMS e hahiloeng ka sebopeho sa capacitive sensing le sebopeho sa IC. Ntho ea kutlo, e khonang ho bona maqhubu a acoustic, e etsoa ka mokhoa o khethehileng oa silicon micromachining o ikemiselitseng ho hlahisa li-audio sensors.
Sefate sa Matla
Boto e ka tsamaisoa ka sehokelo sa USB, VIN kapa VUSB lithareng.
tšōmo
HLOKOMELA: Kaha VUSB e fepa VIN ka diode ea Schottky le molaoli oa DC-DC o boletse bonyane matla a ho kenya.tage ke 4.5V bonyane ba phepelo ea matlatage ho tloha ho USB e tlameha ho eketseha ho ea ho voltage sebakeng se pakeng tsa 4.8V le 4.96V, ho itšetlehile ka hore na ha joale e huloa joang.
Ts'ebetso ea Boto
Ho qala - IDE
Haeba u batla ho hlophisa Nano 33 BLE Sense Rev2 ha u ntse u le sieo, u lokela ho kenya Arduino Desktop IDE [1] Ho hokela Nano 33 BLE Sense Rev2 komporong ea hau, u tla hloka thapo ea Micro-B ea USB. Sena se boetse se fana ka matla ho boto, joalokaha ho bontšitsoe ke LED.
Ho qala - Arduino Cloud Editor
Liboto tsohle tsa Arduino, ho kenyeletsoa le ena, li sebetsa ka ntle ho lebokose ho Arduino Cloud Editor [2], ka ho kenya plugin e bonolo feela.
Arduino Cloud Editor e tsamaisoa inthaneteng, ka hona e tla lula e le morao-rao ka likarolo tsa morao-rao le tšehetso bakeng sa liboto tsohle. Latela [3] ho qala ho khouta sebatli le ho kenya litšoantšo tsa hau botong ea hau.
Ho qala - Arduino Cloud
Lihlahisoa tsohle tse nolofalitsoeng tsa Arduino IoT li tšehetsoa ho Arduino Cloud e u lumellang hore u kene, u kenye le ho sekaseka lintlha tsa sensor, ho qala liketsahalo, le ho iketsetsa ntlo kapa khoebo ea hau.
Sample Sketches
Sample litšoantšo tsa Nano 33 BLE Sense Rev2 li ka fumanoa ho "Examples" ho Arduino IDE kapa karolong ea "Documentation" ea Arduino Docs. websebaka.
Lisebelisoa tsa Marang-rang
Kaha joale u se u fetile linthong tsa motheo tsa seo u ka se etsang ka boto u ka hlahloba menyetla e sa feleng eo e fanang ka eona ka ho hlahloba merero e thabisang ho Arduino Project Hub [4], Arduino Library Reference [5] le lebenkeleng la marang-rang moo u tla khona ho tlatsana le boto ea hau ka li-sensor, li-actuator le tse ling.
Boto ea Pholiso
Liboto tsohle tsa Arduino li na le bootloader e hahelletsoeng ka hare e lumellang ho khantša boto ka USB. Haeba sketch e notlela processor mme boto ha e sa fumaneha ka USB, hoa khoneha ho kenya mokhoa oa bootloader ka ho tlanya habeli konopo ea reset hang ka mor'a hore motlakase o theohe.
Sehokedi Pinouts
USB
| Pin | Mosebetsi | Mofuta | Tlhaloso |
| 1 | VUSB | Matla | Phepelo ea Matla. Haeba boto e tsamaisoa ka VUSB ho tloha hloohong sena ke Output (1) |
| 2 | D- | Tse fapaneng | Lintlha tse fapaneng tsa USB - |
| 3 | D+ | Tse fapaneng | Lintlha tse fapaneng tsa USB + |
| 4 | ID | Analoge | E khetha tšebetso ea Host/Device |
| 5 | GND | Matla | Sebaka sa Matla |
Lihlooho
Boto e pepesa lihokelo tse peli tsa phini tse 15 tse ka bokelloang ka lihlooho tsa phini kapa tsa rekisoa ka li-vias tse khabisitsoeng.
| Pin | Mosebetsi | Mofuta | Tlhaloso |
| 1 | D13 | Dijithale | GPIO |
| 2 | +3V3 | Tlosa Matla | Matla a hlahisoang ka hare ho lisebelisoa tsa kantle |
| 3 | AREF | Analoge | Tlhaloso ea Analog; e ka sebelisoa e le GPIO |
| 4 | A0/DAC0 | Analoge | ADC in/DAC tsoa; e ka sebelisoa e le GPIO |
| 5 | A1 | Analoge | ADC ka; e ka sebelisoa e le GPIO |
| 6 | A2 | Analoge | ADC ka; e ka sebelisoa e le GPIO |
| 7 | A3 | Analoge | ADC ka; e ka sebelisoa e le GPIO |
| 8 | A4/SDA | Analoge | ADC ka; I2C SDA; E ka sebelisoa e le GPIO (1) |
| 9 | A5/SCL | Analoge | ADC ka; I2C SCL; E ka sebelisoa e le GPIO (1) |
| 10 | A6 | Analoge | ADC ka; e ka sebelisoa e le GPIO |
| 11 | A7 | Analoge | ADC ka; e ka sebelisoa e le GPIO |
| 12 | VUSB | Matla ka hare/Kantle | Ka tloaelo NC; e ka hokela ho VUSB phini ea sehokelo sa USB ka ho khutsufatsa jumper |
| 13 | RST | Digital In | Kenyo e sebetsang e tlase ea ho seta bocha (kopi ea phini ea 18) |
| 14 | GND | Matla | Sebaka sa Matla |
| 15 | VIN | Power In | Ho kenya Matla a Vin |
| 16 | TX | Dijithale | UART TX; e ka sebelisoa e le GPIO |
| 17 | RX | Dijithale | UART RX; e ka sebelisoa e le GPIO |
| 18 | RST | Dijithale | Kenyo e sebetsang e tlase ea ho seta bocha (kopi ea phini ea 13) |
| 19 | GND | Matla | Sebaka sa Matla |
| 20 | D2 | Dijithale | GPIO |
| 21 | D3/PWM | Dijithale | GPIO; e ka sebelisoa e le PWM |
| 22 | D4 | Dijithale | GPIO |
| 23 | D5/PWM | Dijithale | GPIO; e ka sebelisoa e le PWM |
| 24 | D6/PWM | Dijithale | GPIO, e ka sebelisoa e le PWM |
| 25 | D7 | Dijithale | GPIO |
| 26 | D8 | Dijithale | GPIO |
| 27 | D9/PWM | Dijithale | GPIO; e ka sebelisoa e le PWM |
| 28 | D10/PWM | Dijithale | GPIO; e ka sebelisoa e le PWM |
| 29 | D11/MOSI | Dijithale | SPI MOSI; e ka sebelisoa e le GPIO |
| Pin | Mosebetsi | Mofuta | Tlhaloso |
| 30 | D12/MISO | Dijithale | SPI MISO; e ka sebelisoa e le GPIO |
Hlakola
Ka lehlakoreng le ka tlase la boto, tlas'a mojule oa puisano, matšoao a debug a hlophisitsoe joalo ka lipampiri tsa liteko tsa 3 × 2 tse nang le 100 mil pitch e nang le pin 4 e tlositsoeng. Pin 1 e bonts'itsoe ho Setšoantšo sa 3 - Maemo a Sehokelo
| Pin | Mosebetsi | Mofuta | Tlhaloso |
| 1 | +3V3 | Tlosa Matla | Matla a hlahisoang ka hare a tla sebelisoa e le voltage referense |
| 2 | SWD | Dijithale | nRF52480 data ea Single Wire Debug |
| 3 | SWCLK | Digital In | nRF52480 Single Wire Debug Clock |
| 5 | GND | Matla | Sebaka sa Matla |
| 6 | RST | Digital In | Kenyo e sebetsang e tlase ea ho seta bocha |
Boitsebiso ba Mechini
Kemiso ea Boto le Likoti tse Homang
Mehato ea boto e tsoakane pakeng tsa metric le imperial. Mehato ea borena e sebelisoa ho boloka 100 mil pitch grid pakeng tsa mela ea phini ho ba lumella ho lekana le boardboard athe bolelele ba boto ke Metric.
Setifikeiti
Declaration of Conformity CE DoC (EU)
Re phatlalatsa tlas'a boikarabelo ba rona hore lihlahisoa tse ka holimo li lumellana le litlhoko tsa bohlokoa tsa Litaelo tse latelang tsa EU 'me kahoo re tšoaneleha bakeng sa ho tsamaea ka bolokolohi ka har'a limmaraka tse kenyeletsang European Union (EU) le European Economic Area (EEA).
Phatlalatso ea Tumellano le EU RoHS & REACH 211 01/19/2021
Liboto tsa Arduino li lumellana le RoHS 2 Directive 2011/65/EU ea Paramente ea Europe le RoHS 3 Directive 2015/863/EU ea Lekhotla la 4 Phuptjane 2015 mabapi le thibelo ea tšebeliso ea lintho tse ling tse kotsi ho lisebelisoa tsa motlakase le tsa elektroniki.
| Ntho | Bolelele ba moeli (ppm) |
| Lebisa (Pb) | 1000 |
| Cadmium (Cd) | 100 |
| Motsoako (Hg) | 1000 |
| Hexavalent Chromium (Cr6+) | 1000 |
| Poly Brominated Biphenyls (PBB) | 1000 |
| Poly Brominated Diphenyl ethers (PBDE) | 1000 |
| Bis(2-Ethylhexyl} phthalate (DEHP) | 1000 |
| Benzyl butyl phthalate (BBP) | 1000 |
| Dibutyl phthalate (DBP) | 1000 |
| Diisobutyl phthalate (DIBP) | 1000 |
Litokollo: Ha ho litokollo tse batloang.
Arduino Boards e lumellana ka botlalo le litlhoko tse amanang le European Union Regulation (EC) 1907 /2006 mabapi le Ngoliso, Tlhahlobo, Tumello le Thibelo ea Lik'hemik'hale (REACH). Ha re phatlalatse hore ha ho le e 'ngoe ea SVHCs (https://echa.europa.eu/web/guest/candidate-list-table), Lethathamo la Bakhethoa ba Matšoenyeho a Holimo Haholo bakeng sa tumello e lokollotsoeng hajoale ke ECHA, le teng lihlahisoang tsohle (le sephutheloana) ka bongata bo boholo bo lekanang kapa bo kaholimo ho 0.1%. Ho latela tsebo ea rona, re boetse re phatlalatsa hore lihlahisoa tsa rona ha li na letho la lintho tse thathamisitsoeng ho "Authorization List" (Annex XIV ea melaoana ea REACH) le Substances of Very High Concern (SVHC) ka chelete efe kapa efe ea bohlokoa joalo ka ha e boletsoe. ka Sehlomathiso sa XVII sa Lethathamo la Bakhethoa le hatisitsoeng ke ECHA (European Chemical Agency) 1907 /2006/EC.
Phatlalatso ea Liminerale tsa Khohlano
Joaloka mofani oa lefats'e oa lisebelisoa tsa elektroniki le tsa motlakase, Arduino e tseba boitlamo ba rona mabapi le melao le melaoana e amanang le Conflict Minerals, haholoholo Dodd-Frank Wall Street Reform and Consumer Protection Act, Karolo ea 1502. Arduino ha e hlahise kapa ha e sebetsane le likhohlano ka kotloloho. liminerale tse kang Tin, Tantalum, Tungsten, kapa Khauta. Liminerale tse loantšanang li fumaneha lihlahisoa tsa rona ka mokhoa oa solder, kapa e le karolo ea li-alloys tsa tšepe. E le karolo ea boitelo ba rona bo loketseng, Arduino e ikopanye le bafani ba thepa ba ka har'a ketane ea rona ea phepelo ho netefatsa hore ba tsoela pele ho latela melao. Ho ipapisitsoe le tlhaiso-leseling eo re e fumaneng ho tla fihlela joale, re phatlalatsa hore lihlahisoa tsa rona li na le Liminerale tsa Conflict tse tsoang libakeng tse se nang likhohlano.
FCC
FCC Tlhokomeliso
Liphetoho life kapa life tse sa amoheloeng ka kotloloho ke mokha o ikarabellang bakeng sa tsamaiso li ka hlakola matla a mosebelisi a ho sebelisa sesebelisoa. Sesebelisoa sena se lumellana le karolo ea 15 ea Melao ea FCC. Ts'ebetso e ipapisitse le maemo a mabeli a latelang:
- Sesebelisoa sena se ka 'na sa se ke sa baka tšitiso e kotsi
- sesebelisoa sena se tlameha ho amohela tšitiso efe kapa efe e amohetsoeng, ho kenyeletsoa tšitiso e ka bakang ts'ebetso e sa batleheng.
Polelo ea Ts'oaetso ea Mahlaseli a FCC RF:
- Transmitter ena ha ea lokela ho ba sebakeng se le seng kapa ho sebetsa mmoho le antenna efe kapa efe kapa transmitter.
- Sesebelisoa sena se lumellana le meeli ea ho pepeseha ha mahlaseli a RF e behiloeng bakeng sa tikoloho e sa laoleheng.
- Thepa ena e lokela ho kengoa le ho sebetsoa ka sebaka sa bonyane 20cm lipakeng tsa radiator le 'mele oa hau.
Litaelo tsa mosebelisi bakeng sa lisebelisoa tsa seea-le-moea tse sa lumelloeng ke laesense li tla ba le tsebiso e latelang kapa e ts'oanang le eona sebakeng se hlakileng bukeng ea mosebelisi kapa sesebelisoa kapa ka bobeli. Sesebediswa sena se dumellana le ditekanyetso tsa RSS tse sa dumelleng laesense ya Industry Canada. Ts'ebetso e ipapisitse le maemo a mabeli a latelang:
- sesebelisoa sena se ka 'na sa se ke sa baka tšitiso
- sesebelisoa sena se tlameha ho amohela tšitiso efe kapa efe, ho kenyeletsoa tšitiso e ka bakang ts'ebetso e sa batleheng ea sesebelisoa.
Tlhokomeliso ea IC SAR:
Sesotho Thepa ena e lokela ho kenngoa le ho sebetsoa ka sebaka sa bonyane 20 cm pakeng tsa radiator le 'mele oa hau.
Bohlokoa: Thempereichara ea ho sebetsa ea EUT e ke ke ea feta 85 ℃ 'me ha ea lokela ho ba ka tlase ho -40 ℃.
Ka hona, Arduino Srl e phatlalatsa hore sehlahisoa sena se lumellana le litlhoko tsa bohlokoa le lipehelo tse ling tse amehang tsa Directive 2014/53/EU. Sehlahisoa sena se lumelletsoe ho sebelisoa linaheng tsohle tsa litho tsa EU.
| Maqhubu a maqhubu | Matla a phahameng haholo (ERP) |
| 863-870Mhz | TBD |
Lintlha tsa Khampani
| Lebitso la K'hamphani | Arduino Srl |
| Aterese ea Khampani | Via Andrea Appiani 25 20900 MONZA Italy |
Litokomane Tsa Litšupiso
| Referense | Sehokelo |
| Arduino IDE (Desktop) | https://www.arduino.cc/en/software |
| Arduino Cloud Editor | https://create.arduino.cc/editor |
| Arduino Cloud Editor - Ho qala | https://docs.arduino.cc/arduino-cloud/guides/editor/ |
| Arduino Project Hub | https://create.arduino.cc/projecthub?by=part&part_id=11332&sort=trending |
| Reference Library | https://www.arduino.cc/reference/en/ |
| Foramo | https://create.arduino.cc/projecthub/Arduino_Genuino/getting-started-with- arduino -web-mohlophisi-4b3e4a |
| Kena B306 | https://content.u-blox.com/sites/default/files/NINA-B3_DataSheet_UBX- 17052099.pdf |
| Laeborari ea Arduino_LPS22HB | https://github.com/arduino-libraries/Arduino_LPS22HB |
| Laeborari ea Arduino_APDS9960 | https://github.com/arduino-libraries/Arduino_APDS9960 |
Nalane ea Phetoho
| Letsatsi | Khatiso | Liphetoho |
| 25/04/2024 | 5 | Sehokelo se ntlafalitsoeng sa Cloud Editor se secha |
| 03/05/2023 | 4 | Kenya SKU bakeng sa mofuta o nang le lihlooho |
| 10/11/2022 | 3 | E ntlafaditswe ho akhaonteng bakeng sa diphetoho tsa Rev2: LSM9DS1 -> BMI270+Bmm150, HTS221 -> HS3003, MPM3610 -> MP2322, PCB tokiso |
| 03/08/2022 | 2 | Litokomane tsa litšupiso li hokahanya lintlafatso |
| 27/04/2021 | 1 | Lintlafatso tse akaretsang tsa database |
FAQs
- P: Na boto e ka tsamaisoa ke betri?
- A: Nano 33 BLE Sense Rev2 ha e na tjhaja ea betri empa e ka tsamaisoa ka USB kapa lihlooho.
- P: Ke matla afe a khothalletsoang a ho sebetsatage bakeng sa boto?
- A: Boto e tšehetsa 3.3VI / Os feela 'me ha e mamelle matšoao a 5V.
Litokomane / Lisebelisoa
 |
Arduino ABX00069 Nano 33 BLE Sense Rev2 3.3V AI e Nobled Board [pdf] Bukana ea Mosebelisi ABX00069, ABX00070, ABX00069 Nano 33 BLE Sense Rev2 3.3V AI E Nobled Board, ABX00069, Nano 33 BLE Sense Rev2 3.3V AI E Nobled Board, BLE Sense Rev2 3.3V AI Enbled AI |