Arduino ABX00069 Nano 33 BLE Sense Rev2 3.3V AI Ho'ā Papa
Nā hiʻohiʻona
- NINA B306 Module
- Mea hana
- 64 MHz Arm® Cortex®-M4F (me FPU)
- 1 MB Flash + 256 kB RAM
- Bluetooth® 5 multiprotocol radio
- 2 Mbps
- CSA #2
- Hoʻonui hoʻolaha
- Lāʻau lōʻihi
- +8 dBm TX mana
- -95 dBm ʻike
- 4.8 mA i TX (0 dBm)
- 4.6 mA i RX (1 Mbps)
- ʻO ka balun i hoʻohui ʻia me 50 Ω hoʻopau hoʻokahi
- Kākoʻo lekiō IEEE 802.15.4
- Loko
- Zigbee
- Pilipili
- 12 Mbps USB ka māmā holo piha
- NFC-A tag
- Pūnaehana palekana Arm CryptoCell CC310
- QSPI/SPI/TWI/I²S/PDM/QDEC
- ʻO ka wikiwiki kiʻekiʻe 32 MHz SPI
- Pākuʻi SPI Quad 32 MHz
- EasyDMA no nā kikowaena kikohoʻe a pau
- 12-bit 200 ksps ADC
- 128 bit AES/ECB/CCM/AAR kaʻina hana
- BMI270 6-axis IMU (Accelerometer and Gyroscope) 16-bit
- 3-axis accelerometer me ±2g/±4g/±8g/±16g laula
- 3-axis gyroscope me ±125dps/±250dps/±500dps/±1000dps/±2000dps laula
- BMM150 3-axis IMU (Magnetometer)
- 3-axis digital geomagnetic sensor
- 0.3μT hoʻonā
- ±1300μT (x,y-axis), ±2500μT (z-axis)
- LPS22HB (Barometer a me ka ʻike wela)
- 260 a hiki i ka 1260 hPa pumehana piha me ka pololei 24 bit
- Hiki ke hoʻokiʻekiʻe kiʻekiʻe: 20x piha piha
- Pānaʻi wela i hoʻokomo ʻia
- 16-bit ka ʻikepili wela
- 1 Hz a i 75 Hz ka helu ʻikepili pukana Nā hana hoʻopaʻa: Mākaukau ʻikepili, nā hae FIFO, nā paepae kaomi
- HS3003 Mahana & mīkini ʻume mākenēki
- 0-100% ka palena haʻahaʻa pili
- Pono pono haʻahaʻa: ±1.5%RH, maʻamau (HS3001, 10 a 90% RH,25°C)
- Pono ka ʻike wela: ±0.1°C, maʻamau
- A hiki i ka 14-bit humidity a me ka ʻikepili puka wela
- APDS-9960 (Hoʻokokoke kikohoʻe, kukui ambient, RGB a me ka ʻike ʻike)
- Māmā Ambient a me RGB Color Sensing me nā kānana pale UV a me IR
- Kiʻekiʻe kiʻekiʻe - kūpono no ka hana ma hope o ke aniani ʻeleʻele
- ʻO ka ʻike kokoke me ka hōʻole ʻana i ka mālamalama ambient
- ʻIke ʻana i ke ʻano paʻakikī
- MP34DT06JTR (Mikopona Kikohoʻe)
- AOP = 122.5 dbSPL
- 64 dB lākiō hōʻailona-a-leo
- ʻOmnidirectional sensitivity
- –26 dBFS ± 3 dB ʻike
- MP2322 DC-DC
- Hoʻoponopono i ka hoʻokomo voltage mai ka 21V me ka liʻiliʻi o 65% ka pono @ @ ka haawe liʻiliʻi
- Ma mua o 85% pono @12V
- Mea hana
IKE HUA
Ka Papa
E like me nā papa kumu kumu Nano a pau, ʻaʻole loaʻa i ka Nano 33 BLE Sense Rev2 kahi pahu pākaukau akā hiki ke hoʻohana ʻia ma o USB a i ʻole nā poʻo.
HOOLAHA: Kākoʻo wale ʻo Nano 33 BLE Sense Rev2 i ka 3.3VI/Os a ʻaʻole ʻae ʻo 5V no laila e ʻoluʻolu e ʻoluʻolu ʻaʻole ʻoe e hoʻopili pololei i nā hōʻailona 5V i kēia papa a i ʻole e pōʻino. Eia kekahi, e kū'ē i nā papa Arduino Nano e kākoʻo ana i ka hana 5V, ʻaʻole hāʻawi ka pin 5V i ka vol.tagakā ua pili ʻia, ma o ka lele, i ka mana hoʻokomo USB.
Heluhelu
Manaʻo ʻia nā kūlana hana
| hōʻailona | wehewehe | Min | Max |
| Nā palena wela conservative no ka papa holoʻokoʻa: | -40 °C (40 °F) | 85°C (185 °F) |
Hoʻohana mana
| hōʻailona | wehewehe | Min | ʻAno | Max | Unite |
| PBL | Hoʻohana mana me ka loop loop | TBC | mW | ||
| PLP | Hoʻohana mana ma ke ʻano mana haʻahaʻa | TBC | mW | ||
| PMAX | Hoʻohana mana kiʻekiʻe | TBC | mW |
Hana ma lunaview
Papa Topology
luna:
Topology papa luna
| Ref. | wehewehe | Ref. | wehewehe |
| U1 | NINA-B306 Module Bluetooth® Low Energy 5.0 Module | U6 | MP2322GQH Hoʻololi i lalo |
| U2 | BMI270 Sensor IMU | PB1 | IT-1185AP1C-160G-GTR Puhi pihi |
| U3 | MP34DT06JTR MEMS Microphone | U8 | HS3003 Hoʻonaʻauao haʻahaʻa |
| U7 | BMM150 Magnetometer IC | DL1 | Led L |
| U5 | APDS-9660 Ambient Module | DL2 | Mana Led |
| U9 | LPS22HBTR Pumi Pumi IC |
lalo:
| Ref. | wehewehe | Ref. | wehewehe |
| SJ1 | VUSB Jumper | SJ2 | ʻO D7 Jumper |
| SJ3 | 3v3 Jumper | SJ4 | ʻO D8 Jumper |
Mea hana
ʻO ka mea hana nui he Arm® Cortex®-M4F e holo ana a hiki i 64MHz. Hoʻopili ʻia ka hapa nui o kāna mau pine i nā poʻomanaʻo o waho, akā mālama ʻia kekahi no ke kamaʻilio kūloko me ka module uea ʻole a me nā peripheral I2C i loko o ka papa (IMU a me Crypto).
HOOLAHA: E like me nā papa Arduino Nano ʻē aʻe, loaʻa nā pine A4 a me A5 i kahi huki kūloko a paʻa ʻole e hoʻohana ʻia ma ke ʻano he I2C Bus no laila ʻaʻole ʻōlelo ʻia ka hoʻohana ʻana e like me nā hoʻokomo analog.
IMU
Hāʻawi ka Nano 33 BLE Sense Rev2 i nā mana IMU me 9-axis, ma ka hui pū ʻana o nā BMI270 a me BMM150 IC. Aia ka BMI270 i ʻekolu axis gyroscope a me ʻekolu axis accelerometer, aʻo ka BMM150 hiki ke ʻike i nā ʻano like ʻole o ka pā magnetic ma nā ʻāpana ʻekolu. Hiki ke hoʻohana ʻia ka ʻike i loaʻa no ke ana ʻana i nā ʻāpana o ka neʻe ʻana a me ke aʻo ʻana i ka mīkini.
LPS22HB (U9) Barometer a me ka ʻike wela
ʻO ka LPS22HB kaomi puʻe IC (U9) e komo pū me ka piezoresistive absolute pressure sensor me ka wela wela i hoʻohui ʻia i loko o kahi puʻupuʻu liʻiliʻi. Hoʻopili ka mea ʻike kaomi (U9) me ka microcontroller nui (U1) ma o kahi interface I2C. Hoʻokumu ʻia ka mea sensing me ka micromachined suspended membrane no ke ana ʻana i ke kaomi piha, a me kahi alahaka Wheatstone i loko no ke ana ʻana i nā mea piezoresistive. Hoʻopaʻi ʻia nā pilikia wela ma o ka mea ʻike wela i hoʻokomo ʻia ma ka chip. Hiki ke piʻi mai ka 260 a hiki i ka 1260 hPa. Hiki ke koho ʻia ka ʻikepili kaomi ma o I2C a hiki i ka 24 bits, ʻoiai hiki ke koho ʻia ka ʻikepili wela a hiki i ka 16-bits. Hāʻawi ka waihona Arduino_LPS22HB i kahi hoʻokō mākaukau o ka protocol I2C me kēia chip.
HS3003 (U8) ʻO ka haʻahaʻa haʻahaʻa a me ka ʻike wela
ʻO ka HS3003 (U8) he mea ʻike MEMS, i hoʻolālā ʻia e hāʻawi i nā heluhelu pololei o ka haʻahaʻa pili a me ka mahana i loko o kahi puʻupuʻu liʻiliʻi. Hana ʻia ka pāhana-uku a me ka calibration ma luna o ka chip, me ka ʻole e koi i ka circuitry waho. Hiki i ka HS3003 ke ana i ka haʻahaʻa pili mai 0% a 100% RH me nā manawa pane wikiwiki (ma lalo o 4 kekona). ʻO ka mea ʻike wela ma luna o ka chip (hoʻohana ʻia no ka uku) he ± 0.1 °C. Kūkākūkā ʻo U8 ma o ka microcontroller nui ma o ka pahi I2C.
ʻIke ʻana
Hoʻohana ka ʻike ʻana i nā kiʻi kiʻi kuhikuhi ʻehā e ʻike ai i ka ikehu IR i hoʻohālikelike ʻia (hoʻokumu ʻia e ka LED i hoʻohui ʻia) e hoʻohuli i ka ʻike o ka neʻe kino (ʻo ia hoʻi ka wikiwiki, kuhikuhi a me ka mamao) i ka ʻike kikohoʻe. ʻO ka hoʻolālā ʻana o ka ʻenekini gesture e hōʻike ana i ka hoʻoulu ʻana (e pili ana i nā hopena engine Proximity), ka unuhi ʻana i nā kukui ambient, ka hoʻopau ʻana i ke kamaʻilio keʻa, nā mea hoʻololi ʻikepili 8-bit ʻelua, hoʻopaneʻe i waena o ka hoʻololi ʻana i ka mana, 32-dataset FIFO, a me ke kamaʻilio I2C i alakaʻi ʻia. Hāʻawi ka ʻenekini gesture i kahi ākea o nā mea e pono ai no ka hōʻailona ʻana: hiki ke ʻike pololei ʻia nā ʻōkuhi UP-DOWN-RIGHT-LEFT maʻalahi. Hoʻemi ʻia ka hoʻohana ʻana i ka mana a me ka walaʻau me ka IR LED manawa kūpono.
ʻIke pili
Hāʻawi ka hiʻona ʻike Proximity i ke ana mamao (e laʻa me ka pale kelepona paʻa i ka pepeiao o ka mea hoʻohana) ma ka ʻike photodiode o ka ikehu IR i hoʻohālikelike ʻia (hoʻokumu ʻia e ka LED i hoʻohui ʻia). Hoʻokuʻu ʻia nā hanana ʻike a hoʻokuʻu ʻia, a loaʻa i kēlā me kēia manawa ke hele ka hopena pili i ka pae o ka paepae o luna a/a i ʻole. Hāʻawi ka ʻenekini kokoke i nā papa inoa hoʻoponopono hoʻoponopono e hoʻopaʻi i ka ʻōnaehana ʻōnaehana i hana ʻia e nā manaʻo ikehu IR makemake ʻole e ʻike ʻia ana ma ka mea ʻike. ʻO ka ikaika o ka IR LED ua ʻoki ʻia ka hale hana e hoʻopau i ka pono no ka calibration o nā mea hana hope ma muli o nā ʻano like ʻole. Hoʻomaikaʻi hou ʻia nā hopena pili e ka unuhi ʻana i nā kukui ambient.
ʻIke kala a me ALS
Hāʻawi ka hiʻohiʻona ʻike ʻula a me ka ALS i ka ʻikepili ʻulaʻula, ʻōmaʻomaʻo, uliuli a me ka māmā. Loaʻa i kēlā me kēia o nā kahawai R, G, B, C kahi kānana pale UV a me IR a me kahi mea hoʻololi ʻikepili hoʻolaʻa e hana ana i ka ʻikepili 16-bit i ka manawa like. Hāʻawi kēia hale hana i nā noi e ana pono i ka mālamalama ambient a me ke kala ʻike e hiki ai i nā mea hana ke helu i ka mahana o ka waihoʻoluʻu a me ka mālama ʻana i ke kukui hōʻike.
Mīkini uila
ʻO ka MP34DT06JTR kahi microphone ultra-compact, low-power, omnidirectional, digital MEMS microphone i kūkulu ʻia me kahi capacitive sensing element a me kahi interface IC. Hana ʻia ka mea sensing, hiki ke ʻike i nā nalu acoustic, me ka hoʻohana ʻana i kahi kaʻina micromachining silicon kūikawā i hoʻolaʻa ʻia no ka hana ʻana i nā mea kani leo.
Laau Mana
Hiki ke hoʻohana ʻia ka papa ma o ka mea hoʻohui USB, nā pine VIN a i ʻole VUSB ma nā poʻo.
kaao
HOOLAHANo ka mea, hānai ʻo VUSB iā VIN ma o kahi diode Schottky a me kahi mea hoʻoponopono DC-DC i kuhikuhi ʻia i ka vol input liʻiliʻi.tagʻo ka 4.5V ka liʻiliʻi loa o ka voltage mai USB pono e hoonui i ka voltage ma waena o 4.8V a i 4.96V, ma muli o ke kaha kiʻi o kēia manawa.
Hana Papa
Hoʻomaka - IDE
Inā makemake ʻoe e hoʻolālā i kāu Nano 33 BLE Sense Rev2 i ka wā ma waho pono ʻoe e hoʻokomo i ka Arduino Desktop IDE [1] No ka hoʻopili ʻana i ka Nano 33 BLE Sense Rev2 i kāu kamepiula, pono ʻoe i kahi uwea Micro-B USB. Hāʻawi kēia i ka mana i ka papa, e like me ka mea i hōʻike ʻia e ka LED.
E hoʻomaka - Arduino Cloud Editor
ʻO nā papa Arduino āpau, me kēia, hana i waho o ka pahu ma ka Arduino Cloud Editor [2], ma ke kau ʻana i kahi plugin maʻalahi.
Hoʻokipa ʻia ka Arduino Cloud Editor ma ka pūnaewele, no laila e hoʻomau mau ʻia me nā hiʻohiʻona hou loa a me ke kākoʻo no nā papa āpau. E hahai i [3] e hoʻomaka i ka hoʻopaʻa inoa ma ka polokalamu kele pūnaewele a hoʻouka i kāu mau kiʻi kiʻi ma kāu papa.
E hoʻomaka - Arduino Cloud
Kākoʻo ʻia nā huahana Arduino IoT āpau ma Arduino Cloud e hiki ai iā ʻoe ke hoʻopaʻa inoa, ka pakuhi a me ka nānā ʻana i ka ʻikepili sensor, hoʻoulu i nā hanana, a hoʻomaʻamaʻa i kou home a ʻoihana paha.
Sample Nā kiʻi kiʻi
SampHiki ke loaʻa nā kiʻi kiʻi no ka Nano 33 BLE Sense Rev2 ma ka "Examples" ma ka Arduino IDE a i ʻole ma ka ʻāpana "Documentation" o nā Arduino Docs webpaena.
Nā kumuwaiwai pūnaewele
I kēia manawa ua hele ʻoe i nā kumu o ka mea hiki iā ʻoe ke hana me ka papa e hiki ai iā ʻoe ke ʻimi i nā mea hiki ʻole ke hāʻawi ʻia ma ka nānā ʻana i nā papahana hoihoi ma Arduino Project Hub [4], ka Arduino Library Reference [5] a me ka hale kūʻai ma ka laina kahi e hiki ai iā ʻoe ke hoʻopiha i kāu papa me nā sensor, actuators a me nā mea hou aku.
Hoola Papa
Loaʻa i nā papa Arduino āpau kahi bootloader i kūkulu ʻia e hiki ai ke hoʻolohi i ka papa ma o USB. Inā hoʻopaʻa ʻia kahi kiʻi kiʻi i ke kaʻina hana a ʻaʻole hiki ke kiʻi hou ʻia ka papa ma o USB hiki ke komo i ke ʻano bootloader ma ke kaomi pālua ʻana i ke pihi hoʻihoʻi ma hope pono o ka mana.
Nā Pinout Hoʻohui
USB
| Pin | Hana | ʻAno | wehewehe |
| 1 | VUSB | Ka mana | Hookomo Mana Mana. Inā hoʻohana ʻia ka papa ma o VUSB mai ke poʻo he Output kēia (1) |
| 2 | D- | ʻokoʻa | ʻIkepili ʻokoʻa USB - |
| 3 | D+ | ʻokoʻa | ʻIkepili ʻokoʻa USB + |
| 4 | ID | Analog | Koho i ka Host / Device hana |
| 5 | GND | Ka mana | Ka Papa Pā |
Nā poʻomanaʻo
Hōʻike ka papa i ʻelua mau mea hoʻohui pin 15 i hiki ke hui pū ʻia me nā poʻo pine a i ʻole ke kūʻai ʻia ma o nā vias castellated.
| Pin | Hana | ʻAno | wehewehe |
| 1 | D13 | Kikohoʻe | GPIO |
| 2 | +3V3 | Lanakila | Hoʻopuka ʻia ka mana i loko i nā mea waho |
| 3 | AREF | Analog | Analog Reference; hiki ke hoʻohana ʻia e like me GPIO |
| 4 | A0/DAC0 | Analog | ADC i loko/DAC i waho; hiki ke hoʻohana ʻia e like me GPIO |
| 5 | A1 | Analog | ADC ma; hiki ke hoʻohana ʻia e like me GPIO |
| 6 | A2 | Analog | ADC ma; hiki ke hoʻohana ʻia e like me GPIO |
| 7 | A3 | Analog | ADC ma; hiki ke hoʻohana ʻia e like me GPIO |
| 8 | A4/SDA | Analog | ADC ma; I2C SDA; Hiki ke hoʻohana ʻia e like me GPIO (1) |
| 9 | A5/SCL | Analog | ADC ma; I2C SCL; Hiki ke hoʻohana ʻia e like me GPIO (1) |
| 10 | A6 | Analog | ADC ma; hiki ke hoʻohana ʻia e like me GPIO |
| 11 | A7 | Analog | ADC ma; hiki ke hoʻohana ʻia e like me GPIO |
| 12 | VUSB | Ka mana komo/waho | ʻO ka maʻamau NC; hiki ke hoʻopili ʻia i ka pine VUSB o ka mea hoʻohui USB ma ka pōkole ʻana i kahi jumper |
| 13 | RST | Digital In | Hoʻokomo hoʻihoʻi haʻahaʻa haʻahaʻa (ke kope o ka pine 18) |
| 14 | GND | Ka mana | Ka Papa Pā |
| 15 | VIN | Mana In | Hoʻokomo mana Vin |
| 16 | TX | Kikohoʻe | USART TX; hiki ke hoʻohana ʻia e like me GPIO |
| 17 | RX | Kikohoʻe | USART RX; hiki ke hoʻohana ʻia e like me GPIO |
| 18 | RST | Kikohoʻe | Hoʻokomo hoʻihoʻi haʻahaʻa haʻahaʻa (ke kope o ka pine 13) |
| 19 | GND | Ka mana | Ka Papa Pā |
| 20 | D2 | Kikohoʻe | GPIO |
| 21 | D3/PWM | Kikohoʻe | GPIO; hiki ke hoʻohana ʻia e like me PWM |
| 22 | D4 | Kikohoʻe | GPIO |
| 23 | D5/PWM | Kikohoʻe | GPIO; hiki ke hoʻohana ʻia e like me PWM |
| 24 | D6/PWM | Kikohoʻe | GPIO, hiki ke hoʻohana ʻia e like me PWM |
| 25 | D7 | Kikohoʻe | GPIO |
| 26 | D8 | Kikohoʻe | GPIO |
| 27 | D9/PWM | Kikohoʻe | GPIO; hiki ke hoʻohana ʻia e like me PWM |
| 28 | D10/PWM | Kikohoʻe | GPIO; hiki ke hoʻohana ʻia e like me PWM |
| 29 | D11/MOSI | Kikohoʻe | SPI MOSI; hiki ke hoʻohana ʻia e like me GPIO |
| Pin | Hana | ʻAno | wehewehe |
| 30 | D12/MISO | Kikohoʻe | SPI MISO; hiki ke hoʻohana ʻia e like me GPIO |
Debug
Ma ka ʻaoʻao lalo o ka papa, ma lalo o ka module kamaʻilio, hoʻonohonoho ʻia nā hōʻailona debug e like me 3 × 2 mau papa hoʻāʻo me 100 mil pitch me ka pine 4 i wehe ʻia. Hōʻike ʻia ka Pin 1 ma ke Kiʻi 3 - Nā kūlana hoʻohui
| Pin | Hana | ʻAno | wehewehe |
| 1 | +3V3 | Lanakila | E hoʻohana ʻia ka mana i hana ʻia e like me voltage kuhikuhi |
| 2 | SWD | Kikohoʻe | nRF52480 Hoʻokahi Uea Debug ʻIkepili |
| 3 | SWCLK | Digital In | nRF52480 Hoʻokahi Uea Debug Uaki |
| 5 | GND | Ka mana | Ka Papa Pā |
| 6 | RST | Digital In | Hoʻokomo haʻahaʻa hana hou |
ʻIke Mechanical
Papa Hoike a me na Puwa Kauwa
Hoʻohui ʻia nā ana papa ma waena o ka metric a me ka imperial. Hoʻohana ʻia nā ana Imperial no ka mālama ʻana i 100 mil pitch grid ma waena o nā lālani pine e hiki ai iā lākou ke hoʻokomo i kahi papa palaoa a ʻo ka lōʻihi o ka papa he Metric.
Nā palapala hōʻoia
Hōʻike o ka Kulike CE DoC (EU)
Ke haʻi aku nei mākou ma lalo o kā mākou kuleana hoʻokahi e pili ana nā huahana i luna me nā koi koʻikoʻi o ka EU Directives a no laila ua kūpono i ka neʻe manuahi i loko o nā mākeke e pili ana i ka European Union (EU) a me ka European Economic Area (EEA).
Hōʻike i ka hoʻokō ʻana i ka EU RoHS & REACH 211 01/19/2021
Hoʻopili nā papa Arduino i ka RoHS 2 Directive 2011/65/EU o ka European Parliament a me RoHS 3 Directive 2015/863/EU o ka Council of 4 June 2015 ma ka palena o ka hoʻohana ʻana i kekahi mau mea pōʻino i nā lako uila a me nā lako uila.
| mea waiwai | palena palena kiʻekiʻe (ppm) |
| Kēpau (Pb) | 1000 |
| Kāmium (Cd) | 100 |
| Mercury (Hg) | 1000 |
| Hexavalent Chromium (Cr6+) | 1000 |
| Poly Brominated Biphenyls (PBB) | 1000 |
| Poly Brominated Diphenyl ethers (PBDE) | 1000 |
| Bis(2-Ethylhexyl} phthalate (DEHP) | 1000 |
| Benzyl butyl phthalate (BBP) | 1000 |
| Dibutyl phthalate (DBP) | 1000 |
| Diisobutyl phthalate (DIBP) | 1000 |
Hoʻokuʻu ʻia: ʻAʻole koi ʻia nā hoʻokuʻu.
Hoʻokō piha nā Papa Arduino i nā koi pili o ka European Union Regulation (EC) 1907/2006 e pili ana i ke kākau inoa, loiloi, ʻae a me ka hoʻopaʻa ʻana i nā mea kemika (REACH). ʻAʻole mākou e haʻi aku i kekahi o nā SVHC (https://echa.europa.eu/web/guest/candidate-list-table), ʻo ka Papa inoa o nā moho o ka manaʻo kiʻekiʻe loa no ka ʻae i hoʻokuʻu ʻia e ECHA i kēia manawa, aia i nā huahana āpau (a me ka pūʻolo pū kekahi) i ka nui o ka hoʻonui ʻana i ka ʻike like a i ʻole ma luna o 0.1%. I ka maikaʻi o ko mākou ʻike, ke haʻi aku nei mākou ʻaʻole i loaʻa i kā mākou huahana kekahi o nā mea i helu ʻia ma ka "Papa Manaʻo" (Annex XIV o nā lula REACH) a me nā Substances of Very High Concern (SVHC) i nā helu nui e like me ka mea i kuhikuhi ʻia. e ka Annex XVII o ka papa inoa moho i paʻi ʻia e ECHA (European Chemical Agency) 1907 /2006/EC.
Hōʻike Kūkākūkā Minerala
Ma ke ʻano he mea hoʻolako honua o nā ʻāpana uila a me ka uila, ʻike ʻo Arduino i kā mākou kuleana e pili ana i nā kānāwai a me nā hoʻoponopono e pili ana i nā Conflict Minerals, ʻo ia hoʻi ka Dodd-Frank Wall Street Reform and Consumer Protection Act, Section 1502. nā mineral e like me Tin, Tantalum, Tungsten, a i ʻole gula. Aia nā mineral conflict i loko o kā mākou huahana ma ke ʻano o ka solder, a i ʻole ma ke ʻano he ʻāpana i nā mea hao. Ma ke ʻano he ʻāpana o kā mākou mākau kūpono kūpono ua hoʻopili ʻo Arduino i nā mea hoʻolako ʻāpana i loko o kā mākou kaulahao lako e hōʻoia i ko lākou hoʻomau ʻana i nā lula. Ma muli o ka ʻike i loaʻa a hiki i kēia manawa ke haʻi aku nei mākou aia kā mākou huahana i nā Conflict Minerals i loaʻa mai nā wahi hakakā ʻole.
FCC
FCC akahele
ʻO nā hoʻololi a i ʻole nā hoʻololi i ʻae ʻole ʻia e ka ʻaoʻao kuleana no ka hoʻokō hiki ke hoʻopau i ka mana o ka mea hoʻohana e hana i nā lako. Hoʻopili kēia mea hana i ka ʻāpana 15 o nā Rula FCC. Aia ka hana i nā kūlana ʻelua:
- ʻAʻole hiki i kēia mea hana ke hoʻopilikia ʻino
- pono e ʻae kēia hāmeʻa i nā hoʻopilikia i loaʻa, me ka hoʻopili ʻana i hiki ke hoʻokō i ka hana makemake ʻole.
ʻO FCC RF Radiation Exposure Statement:
- ʻAʻole pono e hoʻopili ʻia kēia Transmitter a i ʻole e hana pū me kekahi antenna a i ʻole transmitter.
- Hoʻopili kēia mea hana i nā palena hōʻike radiation RF i hoʻonohonoho ʻia no kahi kaiapuni ʻole.
- Pono e hoʻokomo a hana ʻia kēia mea hana me ka liʻiliʻi loa he 20cm ma waena o ka radiator a me kou kino.
Loaʻa i nā puke mea hoʻohana no nā mea lekiō i hoʻokuʻu ʻia i ka laikini ka hoʻolaha ma hope a i ʻole ka like ma kahi ʻike ʻia ma ka manual mea hoʻohana a i ʻole ma ka hāmeʻa a i ʻole nā mea ʻelua. Hoʻopili kēia hāmeʻa i ka maʻamau RSS i hoʻokuʻu ʻia i ka laikini ʻo Industry Canada. Aia ka hana i nā kūlana ʻelua:
- ʻAʻole hiki i kēia mea hana ke hoʻopilikia
- pono e ʻae kēia hāmeʻa i kekahi keakea, me ke keakea ʻana e hiki ai ke hoʻohana ʻole ʻia ka mea hana.
'Ōlelo Aʻo IC SAR:
'Ōlelo Pelekania Pono e ho'okomo a ho'ohana 'ia me ka li'ili'i loa he 20 knm ma waena o ka radiator a me kou kino.
Mea nui: ʻAʻole hiki ke ʻoi aku ka mahana hana o ka EUT ma mua o 85 ℃ a ʻaʻole pono e emi ma lalo o -40 ℃.
Ma kēia, haʻi aku ʻo Arduino Srl e pili ana kēia huahana i nā koi koʻikoʻi a me nā ʻōlelo kūpono ʻē aʻe o Directive 2014/53/EU. Ua ʻae ʻia kēia huahana e hoʻohana i nā mokuʻāina lālā o EU.
| Nā pūʻulu alapine | Ka mana puka kiʻekiʻe loa (ERP) |
| 863-870Mhz | TBD |
ʻIkepili Hui
| inoa hui | Arduino Srl |
| Wahi Hui | Via Andrea Appiani 25 20900 MONZA Italia |
Palapala Kuhikuhi
| Kuhikuhi | loulou |
| Arduino IDE (Pakukau) | https://www.arduino.cc/en/software |
| Arduino Cloud Lunahooponopono | https://create.arduino.cc/editor |
| ʻO Arduino Cloud Editor - Hoʻomaka | https://docs.arduino.cc/arduino-cloud/guides/editor/ |
| Arduino Project Hub | https://create.arduino.cc/projecthub?by=part&part_id=11332&sort=trending |
| Ka Waihona Puke | https://www.arduino.cc/reference/en/ |
| Forum | https://create.arduino.cc/projecthub/Arduino_Genuino/getting-started-with- arduino-web-hooponopono-4b3e4a |
| Nina B306 | https://content.u-blox.com/sites/default/files/NINA-B3_DataSheet_UBX- 17052099.pdf |
| Arduino_LPS22HB Hale Waihona Puke | https://github.com/arduino-libraries/Arduino_LPS22HB |
| Arduino_APDS9960 Hale Waihona Puke | https://github.com/arduino-libraries/Arduino_APDS9960 |
Moolelo Hooponopono
| Lā | Hoʻoponopono | Nā hoʻololi |
| 25/04/2024 | 5 | Hoʻololi ʻia ka loulou i ka Lunahooponopono Cloud hou |
| 03/05/2023 | 4 | Hoʻohui i ka SKU no ka mana me nā poʻomanaʻo |
| 10/11/2022 | 3 | Hoʻohou ʻia i ka helu no nā hoʻololi Rev2: LSM9DS1 -> BMI270+Bmm150, HTS221 -> HS3003, MPM3610 -> MP2322, hoʻololi PCB |
| 03/08/2022 | 2 | Hoʻopili nā palapala kuhikuhi i nā mea hou |
| 27/04/2021 | 1 | Nā hōʻano hou ʻikepili maʻamau |
FAQs
- Nīnau: Hiki ke hoʻoikaika ʻia ka papa e ka pākaukau?
- A: ʻAʻole loaʻa i ka Nano 33 BLE Sense Rev2 kahi kau pākaukau akā hiki ke hoʻohana ʻia ma o USB a i ʻole nā poʻo.
- Q: He aha ka vol voltage no ka papa?
- A: Kākoʻo ka papa i ka 3.3VI/Os wale nō a ʻaʻole ʻae i nā hōʻailona 5V.
Palapala / Punawai
 |
Arduino ABX00069 Nano 33 BLE Sense Rev2 3.3V AI Ho'ā Papa [pdf] Palapala Hoʻohana ABX00069, ABX00070, ABX00069 Nano 33 BLE Sense Rev2 3.3V AI Enabled Board, ABX00069, Nano 33 BLE Sense Rev2 3.3V AI Enabled Board, BLE Sense Rev2 3.3V AI Enabled Board, Enabled Board |