AiM Solo2 DL GPS Lap Timer
Litlhaloso tsa Sehlahisoa
- Sehlahisoa: AiM Solo 2 DL, EVO4S, and ECULog cables for Yamaha YZF-R3 from 2018
- Phatlalatso: 1.00
Tlhahisoleseding ya Sehlahiswa
Mehlala le Lilemo tse Tšehetsoeng:
This user guide explains how to connect AiM Solo 2 DL, EVO4S, and ECULog to Yamaha bikes from the year 2018.
Tlhokomeliso: AiM recommends not to remove the stock dash for models/years mentioned as it may disable some bike functions or safety controls. AiM Tech srl will not be responsible for any consequences resulting from the replacement of the original instrumentation cluster.
Lithapo tsa khokahano
AiM CAN Cables for Solo 2 DL:
- AiM has developed specific connection cables for Solo 2 DL tailored to different bike years.
- Part number of AiM CAN cable for EVO4S only for Yamaha YZF-R3 2018-2021 is: V02585150
AiM CAN Cables for EVO4S and ECULog:
Part number of AiM CAN cable for EVO4S and ECULog for Yamaha YZF-R3 from 2022 is: V02585200
Litaelo tsa Tšebeliso ea Sehlahisoa
Solo 2 DL, EVO4S, and ECULog Connection:
Follow the provided instructions to connect Solo 2 DL, EVO4S, and ECULog cables to your Yamaha YZF-R3 bike according to the respective model year.
Tlhophiso ea RaceStudio 3:
| LEBITSO LA KHALE | MOSEBETSI |
|---|---|
| OBDII RPM | RPM |
| OBDII SPD | Lebelo |
| OBDII TPS | Sensor ea boemo ba throttle |
| OBDII PPS | Sensor ea boemo ba Pedal |
| OBDII ECT | Mocheso oa Metsi |
| OBDII IAT | Batla mocheso oa moea |
| OBDII FuelLev | Boemo ba Mafura |
| OBDII MAP | Khatello ea moea e mengata |
| OBDII MAF | Air Mass Flow |
Temoso ea Tekheniki: Not all data channels outlined in the ECU template are validated for each manufacturer model or variant; some channels are model and year-specific and may not be applicable.
Mehlala le lilemo tse tšehetsoeng
This user guide explains how to connect AiM Solo 2 DL, EVO4S, and ECULog to Yamaha bikes.
Mehlala le lilemo tse tšehetsoeng ke:
- Yamaha YZF-R3
Tlhokomeliso: for this models/years AiM recommends not to remove the stock dash. Doing so will disable some of the bike functions or safety controls. AiM Tech srl will not be held responsible for any consequence that may result from the replacement of the original instrumentation cluster.
Lithapo tsa ho hokela
AiM developed specific connection cables for Solo 2 DL, EVO4S, and ECULog according to the bike year.
AiM CAN cable for Solo 2 DL.
- The part number of the AiM CAN cable for Yamaha YZF-R3 2018-2021 – shown below – is V02569340.
- Setšoantšo se ka tlase se bontša leano la ho haha cable.
- The part number of the AiM CAN cable for Yamaha YZF-R3 from 2022 – shown below – is V02589130.
- Setšoantšo se ka tlase se bontša leano la ho haha cable.
AiM CAN cable for EVO4S and ECULog.
- Part number of AiM CAN cable for EVO4S only for Yamaha YZF-R3 2018-2021 is: V02585150
- Setšoantšo se ka tlase se bontša leano la kaho ea cable.
- The partt number ofthe AiM CAN cable for EVO4S and ECULog for Yamaha YZF-R3 from 2022 is: V02585200.
- Setšoantšo se ka tlase se bontša leano la kaho ea cable.
Khokahano ea Solo 2 DL, EVO4S, le ECULog
Yamaha bikes communicate using the CAN bus. It can be reached:
- on the 4 pins ABS diagnostic Sumitomo connector placed under the bike tail for Yamaha YZF-R3 2018-2021
- on the 6 pins OBDII EU5 connector placed under the bike seat for Yamaha YZF-R3 from 2022.
Sebopeho sa RaceStudio 3
- Pele o hokela lisebelisoa tsa AiM ho baesekele ECU beha mesebetsi eohle u sebelisa software ea AiM RaceStudio 3. Litlhophiso tse lokelang ho khethoa ho tlhophiso ea sesebelisoa ke:
- Moetsi oa ECU: “OBDII”
- Mohlala oa ECU: “CAN” (RaceStudio 3 only)
- After this first selection check the “Silent mode on CAN Bus” checkbox in the device configuration (“ECU Stream” tab) as shown here below.
“OBDII – CAN” protocol
Channels received by AiM devices configured with the “OBDII – CAN” protocol are:
- OBDII RPM RPM
- OBDII SPD Lebelo
- OBDII TPS Sensor ea boemo ba throttle
- OBDII PPS Sensor ea boemo ba Pedal
- OBDII ECT Mocheso oa Metsi
- OBDII IAT Batla mocheso oa moea
- OBDII FuelLev Boemo ba Mafura
- OBDII MAP Khatello ea moea e mengata
- OBDII MAF Air Mass Flow
Technical note: not all data channels outlined in the ECU template are validated for each manufacturer model or variant; some of the outlined channels are model and year-specific, and therefore may not be applicable.
LBH
- Can I use these cables on other motorcycle models?
The AiM Solo 2 DL, EVO4S, and ECULog cables are specifically designed for Yamaha YZF-R3 models. It is recommended to use them only on compatible models. - What should I do if I encounter issues during the connection process?
If you face any difficulties while connecting the cables or configuring the settings, refer to the user manual for troubleshooting steps or contact AiM Tech srl for assistance.
Litokomane / Lisebelisoa
 |
AiM Solo2 DL GPS Lap Timer [pdf] Bukana ea Mosebelisi Solo2 DL, EVO4S, ECULog, Solo2 DL GPS Lap Timer, Solo2 DL, GPS Lap Timer, Lap Timer |
