Srwor V2 Laser
Machine Manual

Operation Video

Please Open The Manual
Let’s experience the process of operating this simple machine together

ABOUT USERS

Dear Srworer,

Thank you for purchasing the SRWOR V2 Laser Glue Remover. Our SRWOR V2 laser machine is a 2-in-1 laser equipment that integrates glue and engraving products for re-pairing the back cover of mobile phones, and is mainly used for mobile phone repairs.
Srwor V2 has auto focus function, eye protection system and laser cooling system, equipped with air filter and mobile phone back cover mold, etc., allowing you to safely remove glue when repairing mobile phones. The high-precision, stable power machine is used with an air filter to bring you the best laser degumming experience and engraving experience.
For your better use and maintenance of the laser machine, please read the manual carefully and follow the steps in the manual.
If you have any questions about the use of the laser machine, please feel free to contact us. We have a professional after-sales team and technical research and development team, which can help you solve all technical problems in time and give you the most reliable experience. Thank you again for your support, we will continue to provide high-quality products and services in the future, and welcome to join us.

Sincerely

MACHINE INTRODUCTION

1. Switch
2. Screen interface
3. Power Interface
4. Data Line Interface
5. Memory Card Slot

1. Filter Switch
2. Power Interface

ACCESSORIES INTRODUCTION

               

Laser Module     Power Supply     Power Cable       Breakout Line*1

                                   

Data Line*2      Screen*3       Blasting Pen*4       Positioning Plate*5

                                         

Fixed Focus Column*6   U Disk*7    Protection Goggle*8   Svcrewdriver Kit*9

                                         

Rubber Pad*10   Thick Tube *11    Thin Tube*12     Back Cover Mold*13

          

Manual                     Filter                          Filter Mask

*1 For simultaneous connection of filters and lasers
*2 For connecting to the screen (can also be used to connect to the computer)
*3 After connecting the machine, it is used to control the machine
*4 For blasting glass backs
*5 For positioning (the position is preset before leaving the factory, generally not needed)
*6 For measuring laser
*7 It is used to update the memory card files later
*8 Anti-laser glasses
*9 M2, M2.5, M3 screwdriver x 1
*10 For raising molds
*11 Thick tube x 1 (for connecting the machine and filter)
*12 Thin tube x 1 (for exhaust)
*13 Used to cover the position of the back cover components of the Apple mobile phone

LASER HEAD INSTALLATION

Laser Module      Screwdriver        M3*4

MACHINE CONNECTION

Power Supply    Power Cable    Breakout Line

Data Line          Screen

MACHINE USE

Turn on the machine power and filter power at the same time

The machine clamps are in a clamped state when leaving the factory, and you need to click the “untie” button on the screen.

Phone

After the clamp is opened, put the mobile phone in the direction as shown in the picture

Click the “Home” button and wait for the machine to automatically position Itself.

Screen

After positioning is complete, click “File”

You can turn the page and select the your phone model

Select the corresponding model and color

Click “preview”

Please observe the laser preview track, ensure that the upper and lower lasers are positioned within the edges of the glass and do not extend beyond the frame boundaries.

Please observe the laser preview path, ensuring that both left and right lasers remain within the edges of the glass and do not exceed the frame boundaries.

Select the corresponding mold and place the mold as shown in the picture, ensuring that the mold can cover the camera, charging coil and cable.

Place the protective cover over and click “Confirm” on the screen. The machine will initiate automatically

FREQUENTLY ASKED QUESTIONS

Before leaving the factory, all machines undergo testing and have their coordinates pre-set. However, it is normal for machines to experience coordinate deviations during transportation. To address this issue, the following measures can be taken:

1.Click on the gear

2.Click to restore factory settings

3.Click to confirm

4.Adjust coordinates via arrow keys

5.Adjust the coordinates of the upper right corner to be the same as the coordinates of the upper right corner of the machine Finally click “Set Origin”

Note! Please refer to the coordinates of the actual machine. The instructions are only for demonstration purposes.

5.1 The fifth point is to add that when the movement distance is too far, you can fine-tune it by setting the mm size.
When the moving speed is too slow, you can deal with it by setting the mm \s speed.
mm&mm\s settings do not affect the speed of glue removal

After completing the above steps, you can click on the file to restart the preview.

If there is still a deviation in the preview path on the machine at this time, you can adjust the coordinates according to the deviation and reset the origin until the preview path is accurate.
(Refer to step 4 step 5 step 5.1)

MACHINE PARAMETERS

Brand Name	Srwor
Model	S1-4045
Series	V2
Power input	DC 12V7A
Equipment material	Aluminum alloy
Engraving range	171mm long, 85mm wide,15mm high
Applicable materials	Wood products, metal paint, leather, plastic, paper products, bamboo, stone
Picture format	JPGE/BMP/TIF/GIF/ SVG
Working Temperature	-20~70 degrees Celsius
Filter tube	5m
Function	One-button automatic positioning  Automatic adjustment of laser height  The camera area automatically compensates for laser height  Remove glue quickly
Software update	Apple mobile phone repair software updates can be directly contacted customer service or downloaded from srwor official website

Stop using at high temperatures

Wear Protective Glasses

Do not look directly at the laser

Avoid Children

Avoid Carving Reflective Objects

INTRODUCTION TO SCREEN BUTTONS

1. Return
2. Arrow key
3. File: Drawing file
4. Status and coordinates
5. Power: Adjust the laser power (no need to set, it has nothing to do with the power of glue removal)
6. Clinch: Clamping fixture
7. Untie: Release the clamp
8. mm: When pressing the arrow keys to move, the distance of a single movement (generally no need to modify)
9. Reset: When the machine is in an abnormal state, you need to click Unlock and then Reset to recover
10. Unlock: When the machine is in an abnormal state, you need to click Unlock and then Reset to recover
11. Set-Origin: Set the coordinate origin of the machine (do not point under normal circumstances!)
12. mm/s: When pressing the arrow keys to move, the speed of a single movement (no need to modify under normal circumstances)
13. Laser moves down
14. Home: For automatic positioning of the machine, you need to put the mobile phone into the fixture and click
15. Laser moves up

HOUSING ASSEMBLY

Users are asked to sort according to the following methods so that the cover can be installed faster and easier.

Accessories 1    Accessories 2    Accessories 3

As shown in the picture, please use “accessory 3” to install No.1 and No. 6.

As shown in the picture, please use “accessories 1” and 2 to install on No.1

As shown in the picture, please use “accessories 2” and “accessories 3” to install on No.2, No.3, No. 4, and No.5

As shown in the picture, please use “accessory 3” to connect No.1, No. 2, No. 3, No. 4 and No. 5 together.

WhatsApp

Contact Us
Service Email: Srwor.spt@gmail.com
Official Website: www.srwor.com

Documents / Resources

SRWOR S1-4045 V2 Laser Machine [pdf] User Manual S1-4045 V2 Laser Machine, S1-4045, V2 Laser Machine, Laser Machine, Machine

References

• User Manual