Srwor V2 Laser Machine Manual

About Users

Dear Srworer,

Thank you for purchasing the SRWOR V2 Laser Glue Remover. Our SRWOR V2 laser machine is a 2-in-1 laser equipment that integrates glue and engraving products for re-pairing the back cover of mobile phones, and is mainly used for mobile phone repairs.

Srwor V2 has auto focus function, eye protection system and laser cooling system, equipped with air filter and mobile phone back cover mold, etc., allowing you to safely remove glue when repairing mobile phones. The high-precision, stable power machine is used with an air filter to bring you the best laser degumming experience and engraving experience.

For your better use and maintenance of the laser machine, please read the manual carefully and follow the steps in the manual.

If you have any questions about the use of the laser machine, please feel free to contact us. We have a professional after-sales team and technical research and development team, which can help you solve all technical problems in time and give you the most reliable experience. Thank you again for your support, we will continue to provide high-quality products and services in the future, and welcome to join us.

Sincerely,

SRWOR

Table of Contents

• Machine Introduction
• Accessories Introduction
• Laser Head Installation
• Machine Connection
• Machine Use
• Supported Model List
• Frequently Asked Questions
• Machine Parameters
• Introduction to Screen Buttons
• Housing Assembly

Machine Introduction

The Srwor V2 Laser Machine features a compact design with accessible ports for various interfaces.

Key components visible include:

• Switch
• Screen Interface
• Power Interface
• Data Line Interface
• Memory Card Slot

The machine also includes a filter system with a filter switch and power interface.

Accessories Introduction

The Srwor V2 comes with a variety of accessories for operation and maintenance:

• Laser Module
• Power Supply
• Power Cable
• Breakout Line
• Data Line
• Screen
• Blasting Pen
• Positioning Plate
• Fixed Focus Column
• U Disk
• Protection Goggle
• Screwdriver Kit
• Rubber Pad
• Thick Tube
• Thin Tube
• Back Cover Mold
• Manual
• Filter
• Filter Mask

Notes on accessories:

• Breakout Line: For simultaneous connection of filters and lasers.
• Data Line: For connecting to the screen (can also be used to connect to the computer).
• Screen: Used to control the machine after connecting.
• Blasting Pen: For blasting glass backs.
• Positioning Plate: For positioning (the position is preset before leaving the factory, generally not needed).
• Fixed Focus Column: For measuring laser.
• U Disk: Used to update memory card files later.
• Protection Goggle: Anti-laser glasses.
• Screwdriver Kit: M2, M2.5, M3 screwdrivers included.
• Rubber Pad: For raising molds.
• Thick Tube: For connecting the machine and filter.
• Thin Tube: For exhaust.
• Back Cover Mold: Used to cover the back cover components of the Apple mobile phone.

Laser Head Installation

To install the laser head, align the Laser Module with the mounting point and secure it using the provided Screwdriver and M3*4 screws.

Machine Connection

Connect the machine components as follows:

1. Connect the Power Supply to the machine using the Power Cable.
2. Connect the Breakout Line to the designated port.
3. Connect the Data Line to the screen.
4. Ensure all connections are secure.

The screen will be used to control the machine's operations.

Machine Use

Initial Setup:

• Turn on the machine power and the filter power simultaneously.
• The machine clamps are in a clamped state when leaving the factory. You need to click the "Untie" button on the screen to release them.

Positioning the Mobile Phone:

• After the clamp is opened, place the mobile phone into the fixture as shown in the picture.
• Click the "Home" button and wait for the machine to automatically position itself.
• After positioning is complete, click "File".
• Navigate through the files to select your phone model.
• Select the corresponding model and color.
• Click "Preview" to observe the laser preview path. Ensure the lasers are within the frame boundaries of the glass.
• Select the corresponding mold and place it to cover the camera, charging coil, and cable.
• Place the protective cover over the mold and click "Confirm" on the screen. The machine will initiate automatically.

Supported Model List

The Srwor V2 Laser Machine supports a wide range of mobile phone models for repair and engraving. Please refer to the software or on-screen menus for the most up-to-date list of compatible models.

Frequently Asked Questions

Coordinate Deviations:

Machines undergo testing before leaving the factory, but coordinate deviations during transportation are normal. To address this:

1. Click the gear icon.
2. Click to restore factory settings.
3. Confirm the reset.
4. Adjust coordinates using the arrow keys.
5. Ensure the coordinates of the upper right corner match the machine's upper right corner, then click "Set Origin".

Fine-tuning Movement:

• If the movement distance is too far, fine-tune by setting the 'mm' size.
• If the moving speed is too slow, adjust the 'mm/s' speed.
• Note: 'mm' and 'mm/s' settings do not affect the speed of glue removal.

After completing the above steps, click on the file to restart the preview. If deviations persist, adjust coordinates and reset the origin until the preview path is accurate.

Machine Parameters

Safety Precautions:

• Avoid using at high temperatures.
• Wear protective glasses.
• Do not look directly at the laser.
• Keep away from children.
• Avoid carving reflective objects.

Introduction to Screen Buttons

The screen interface provides control over the machine's functions:

• Arrow key: Used for moving the laser module. Adjusts movement distance ('mm') and speed ('mm/s').
• Return: Returns to the previous menu or state.
• Laser moves up/down: Controls the vertical movement of the laser.
• Home: Initiates automatic positioning of the mobile phone within the fixture.
• Set Origin: Sets the coordinate origin of the machine.
• Unlock: Releases the clamp or resets the machine in an abnormal state.
• Reset: Recovers the machine from an abnormal state after unlocking.
• Clinch: Clamps the fixture.
• Untie: Releases the clamp.
• Status and coordinates: Displays current machine status and coordinates.
• Power: Adjusts laser power (does not affect glue removal speed).

Housing Assembly

Follow these steps to assemble the housing:

1. Sort accessories as indicated.
2. Use "accessories 2" and "accessories 3" to install on parts No. 2, No. 3, No. 4, and No. 5.
3. Use "accessory 3" to install on parts No. 1 and No. 6.
4. Use "accessories 1" and "accessories 2" to install on part No. 1.
5. Use "accessory 3" to connect parts No. 1, No. 2, No. 3, No. 4, and No. 5 together.