SONOFF ZBM5-86W Zigbee Smart Wall Switch
Power off
WARNING
Please install and maintain the device by a professional electrician. To avoid electric shock hazard, do not operate any connection or contact the terminal connector while the device is powered on!
Wiring instruction
- Choose no neutral required mode or neutral required mode according to your home’s wiring.
- In no neutral required mode: the minimum supported load is 3W, and this device does not support other types of inductive loads such as fans.
- Make sure all wires are connected correctly.
No neutral required mode wiring
Neutral required mode wiring
Download the eWeLink App & Add SONOFF Zigbee gateway.
Scan QR Code to Add Device
Open the eWeLink App and scan the QR code on the device, then follow the instructions given by the app to proceed.
Installation
- Tighten the power module to the mounting box with screws.
- Hook the switch module’s latch into the upper groove of the metal frame.
- Press downward to fix the switch module in place, it will automatically align with the pin positions.
The equipment is only suitable for mounting at heights 2 m
Protective cover
When the wall-mounting box is made of plastic and the size is small, the protective cover can be omitted.
Power on
After powering on, the device will enter the pairing mode defaulted during the first use and the LED signal indicator will “flash slowly’.
The device will exit the Pairing Mode if not paired within 3mins. When you want to enter the pairing mode again, long press the button on the device for 5 seconds until the signal light “flashes slowly/’ and release.
User Manual
https://sonoff.tech/usermanuals
Enter the website provided above to view the User Manual for the device.
- It is suitable for safe use only when the altitude is below 2000m.
- Security risks may arise when the altitude is above 2000m.
- To ensure the safety of your electrical installation, it’s essential either a Miniature Circuit Breaker (MCB) or a Residual Current operated Cicuit-breaker with Integral Overcurrent protection(RCBO) with an electrical rating of 1 OA has been installed before the ZBM5-1 c-86W, ZBM5-2C-86W, ZBM5-3C-86W .
Warning
Under normal use of condition, this equipment should be kept a separation distance of at least 20 cm between the antenna and the body of the user.
EU Declaration of Conformity
Hereby, Shenzhen Sonoff Technologies Co., Ltd. declares that the radioequipment type ZBM5-1 c-86W, ZBM5-2C-86W, ZBM5-3C-86W is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: https://sonoff.tech/compliance/
For CE frequency
- EU Operating Frequency Range
- Zigbee: 2405-2480 MHz
- EU Output Power
- ZigbeeQ0dBm
WEEE Disposal and Recycling Information
All products bearing this symbol are waste electrical and electronic equipment (WEEE as in Directive 2012/19/EU) which should not be mixed with unsorted household waste. Instead, you should protect,human health and the environment by handing over your waste equipment to a designated collection point for the recycling of waste electrical and electronic equipment, appointed by the government or local authorities. Correct disposal and recycling will help prevent potential negative consequences to the environment and human health. Please contact the installer or local authorities for more information about the location as well as terms and conditions of such collection points.
ZBM5-1C-86W:
- Rating/ME3M: 100-240V- 50/60Hz IOA Max Resistive load -m-
- LED: OOV
- Min.load: 3W (No Neutral Required)
- Net weight: 157.3g
- Product dimension: 87x87x40.2mm
Shenzhen Sonoff Technologies Co., Ltd.
- 3F & 6F, BldgA, No. 663, Bulong Rd, Shenzhen, Guangdong, China
- Website: sonoff.tech
- ZIP code: 518000
- Service email: support@itead.cc MADE IN CHINA
Documents / Resources
 |
SONOFF ZBM5-86W Zigbee Smart Wall Switch [pdf] User Guide 86 Type, ZBM5-86W Zigbee Smart Wall Switch, ZBM5-86W, Zigbee Smart Wall Switch, Smart Wall Switch, Switch |