SONOFF D1 Wi-Fi Smart Dimmer Switch User Manual
Operating Instruction
- Power off
To avoid electric shocks, please consult the dealer or a qualified professional for help when installing and repairing! Please do not touch the switch during use. - Wiring instruction
The device can only connect incandescent light bulb and dimmable LED light
Make sure the neutral wire and live wire connection is correct. - Download APP
Android™ & iOS
- Power on
After powering on, the device will enter the quick pairing mode (Touch) during the first use. The connected light enters the “breathing mode”.
It will exit the quick pairing mode (Touch) if the device is not paired within 3mins.
If you need to enter this mode again, please power off and restart the device until the connected light enters the “breathing mode”.
- Add the device
Tap “+” and select “ Quick Pairing ”, then operate following the prompt on the app.
Pairing method for the device and SONOFF RM433 remote controller
Short press any button on the RM433 remote controller within 5s after powering on until you hear “Bi”, which indicates all buttons are paired successfully.
The RM433 remote controller is not included, please purchase it separately
RM433 Introduction
| Buttons | Functions |
 |
On |
 |
Off |
 |
Short press for the low brightness, long press to turn down the brightness |
 |
Short press for the medium brightness, long press to turn down the brightness |
 |
Short press for the higher brightness, long press to turn up the brightness |
 |
Short press for the high brightness, long press to turn up the brightness |
 |
Long press for Ss until you hear “Beep Beep” and release, then the remote controller is cleared successfully. After clearing code is completed, if you need to use, short press any button within Ss after powering on again and you will hearBeer, which indicates the remote controller is paired successfully. |
 |
Long press for Ss until the connected light enters the breathing mode, which indicates the device enters quick pairing mode (Touch), then you can add the light on eWeLink APP. In quick pairing mode, you can short press any button on the remote controller to exit this mode. |
Specifications
| Model | DI |
| Input | 100-240VAC 50/60Hz |
| Output | 100.240VAC 50/60Hz |
| Light Load | Incandescent:200W LED:150W |
| Operating systems | Android & iOS |
| Wi-Fi | IEEE 802.11 b/g/n 2.4GHz |
| RF | 433.92MHz |
| Working temperature | -10°C-40.0 |
| Material | PC VO |
| Dimension | 62x47x32.5mm |
Features
D1 is a Wi-Fi smart dimmer switch that is used to adjust the light brightness and set various atmosphere for your room. You can remotely turn on/off light of your home anywhere, schedule it on/off, or share it with your family to control together.
- Remote Controls
- Single/Countdown Timing
- Voice Control
- Share Control
- Smart Scene
- 433MHz Remote Control
- Stepless dimming
- Scene Mode
- LAN Control
- Group control
Factory Reset
Turn on and off 3 times on repeatedly or delete the connected light on eWeLink
APP until it enters “breathing mode”, then the device is reset successfully and enters quick pairing mode (Touch).
Please reset the device to factory defaults if you want to use other Wi Fi networks, then reconnect the network.
FCC Warning
Changes or modifications not expressly approved by the party responsible for compliance could avoid the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Note
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Hereby, Shenzhen Sonoff Technologies Co., Ltd. declares that the radio equipment type D1 is in compliance with Directive 2014/53/EU.The full text of the EU declaration of conformity is available at the following internet address:
https://sonoff.tech/usermanuals
TX Frequency
WiFi: 2412-2472MHz
RX Frequency
WiFi: 2412-2472MHz SRD: 433.92MHz
Output Power
11.52dBm(802.11b), 11.33dBm(802.11g), 11.07dBm(802.11n20
Shenzhen Sonoff Technologies Co., Ltd.
1001, BLDG8, Lianhua Industrial Park, shenzhen, GD, China
ZIP code: 518000
Website: sonoff.tech
MADE IN CHINA
Documents / Resources
 |
SONOFF D1 Wi-Fi Smart Dimmer Switch [pdf] User Manual D1, Wi-Fi Smart Dimmer Switch |
 |
SONOFF D1 Wi-Fi Smart Dimmer Switch [pdf] User Manual D1 Wi-Fi Smart Dimmer Switch, D1, Wi-Fi Smart Dimmer Switch, Smart Dimmer Switch, Dimmer Switch, Switch |
 |
SONOFF D1 Wi-Fi Smart Dimmer Switch [pdf] User Guide D1 Wi-Fi Smart Dimmer Switch, D1, Wi-Fi Smart Dimmer Switch, Smart Dimmer Switch, Dimmer Switch, Switch |
