SOLAX Pocket Wi-Fi plus LAN V2.0 WiFi+4GM LAN Interface Dongle
Version 0.0
eManual and configuration videos in the QR code or at http://kb.solaxpower.com/
Safety
Descriptions of Labels
CE DECLARATION OF CONFORMITY
- The product conforms to RF specifications and technical standards.
- The device complies with DOC declaration.
- The device meets the basic requirements and other relevant provisions of 2014/53/EU directive.
- The device is allowed to be used in all EU member states.
- Manufacturer: SolaX Power Network Technology (Zhejiang) Co., Ltd. Product type: Pocket WiFi [CE DECLARATION OF COMFORMITY]: https://www.solaxpower.com/uploads/file/pocket-wifi-ce-declaration-of-conformity-en.pdf
FCC RULES
This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible forcompliance could void the user’s authority to operate the equipment.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body
Note:This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Please scan the QR code below for safety regulations in multiple languages:
Packing List
Installation
Additional required materials
Installation steps
WARNING!
Ensure that all power has been turned off at least 5 minutes prior to installation.
This product is equipped with two kinds of communication modes (Wi-Fi or LAN). Users can choose based on actual needs.
Wi-Fi Mode
Installation steps
Step 1: Remove the dust-proof cap on the inverter.
Step 2: Plug in the dongle to the correct port of the inverter. Make sure that the buckles are in the same side.
NOTICE!
Buckles shoud be on the same side.
Installation requirements
For Wi-Fi mode, the longest connection distance between the router and the equipment should be no more than 100 meters; if there is a wall between the router and the equipment, the longest connection distance is 20 meters.
NOTICE
When the Wi-Fi signal is weak, please install a Wi-Fi signal booster at the appropriate location.
LAN mode (general version)
Step 1: Press the buckles on the side of dongle to separate the dongle main body. Then, disassemble the dongle into components 1, 2, 3, 4, and 5; Component 1 is not used for LAN Mode. Keep it in a safe place.
Step 2: Insert the communication cable into components 2, 4, and 5 in sequence. Install the RJ45 terminal with the component 5. Mount the component 3 to the communication cable between component 2 and 4.
Step 3: Clockwise tighten all the components in sequence to complete the LAN assembly.
Step 4: Remove the dust-proof cap on the inverter.
Step 5: Plug in the dongle to the correct port of the inverter.Make sure that the buckles are in the same side.
LAN mode (North American and Japanese version)
Step 1: Press the buckles on the side of dongle to separate the dongle main body. Then, disassemble the dongle into components 1, 2 , 3, 4 and 5; Component 1 and 3 is not used for LAN Mode. Keep it in a safe place.
Step 2: Insert the component 2 and water-proof ring into the corrugated pipe in sequence. Reserve 1-6 mm length over the corrugate pipe to ensure the leakproofness. And the water-proof ring shall be installed in the right direct (as shown in the figure below).
Step 3: Thread the communication cable into the corrugated pipe. Strip the communication cable, install the RJ45 terminal and crimp the terminal.
Step 4: Insert the RJ45 terminal into the corresponding port of component 5. Thread the corrugated pipe and water-proof ring into the component 4. Joint component 4 and 5 together. Tighten the component 2.
Step 5: Remove the dust-proof cap on the inverter.
Step 6: Plug in the dongle to the correct port of the inverter. Make sure that the buckles are in the same side.
Wi-Fi Configuration
Scan the following QR code or search for the keyword “SolaxCloud” in the APP Store to download the Monitoring APP. Scan the following QR code to read the Configuration Guide online.
Technical data
Indicator description
SolaX Power Network Technology (Zhejiang) Co., Ltd.
ADD.: No. 278, Shizhu Road, Chengnan Sub-district, Tonglu County, Hangzhou, Zhejiang, China
E-mail: info@solaxpower.com
www.solaxpower.com
Copyright © SolaX Power Network Technology (Zhejiang) Co., Ltd. All rights reserved.
Documents / Resources
 |
SOLAX Pocket Wi-Fi plus LAN V2.0 WiFi+4GM LAN Interface Dongle [pdf] Instruction Manual 2AMEH-POCKET2, 2AMEHPOCKET2, Pocket Wi-Fi plus LAN V2.0 WiFi 4GM LAN Interface Dongle, Pocket Wi-Fi plus LAN V2.0, WiFi 4GM LAN Interface Dongle, LAN Interface Dongle, Interface Dongle, Dongle |