solaredge Home Smart Switch Installation Guide

solaredge Home Smart Switch

Product Information

• Specifications:
  • AC voltage: 90 ~ 250 Vac
  • AC frequency: 50/60 Hz
  • Switch rating: 16A
  • Poles: 1
  • Relay switching cycles: > 20,000
  • Operating hours: 50,000hr
  • Installation altitude: Up to 2000m
  • Measurement accuracy: 1%

Product Usage Instructions

• Mounting Options:
  • Choose one of the following options Screws:
    • WARNING! Installation is allowed at up to 2000 meters of altitude.
    • Use the provided screws to mount the SolarEdge Home Smart Switch.
  • Double-sided tape:
    • Use the provided double-sided tape to mount the SolarEdge Home Smart Switch.
  • Din rail adapter:
    • Use the provided screws and din rail adapter to mount the SolarEdge Home Smart Switch on a din rail.
• Cabling:
  • Choose one of the following options:
    • A. Insert cables from top and bottom:
      • Insert the cables into the designated slots on the top and bottom of the SolarEdge Home Smart Switch.
    • B. Insert cables from behind:
      • Insert the cables into the designated slots on the back of the SolarEdge Home Smart Switch.
• Wiring:
  • Follow the wiring diagram below:
• Pair with Inverter:
  • Access the SetApp configuration on your SolarEdge inverter.
  • Press and hold the P button for 2 seconds to activate the pairing mode.
• LED Indications:
  • The LED on the SolarEdge Home Smart Switch provides indications for different states:
    • Commissioning: LED blinks during the commissioning process.
    • Device manager: LED indicates a successful connection to the device manager.
    • Found new devices: LED indicates new devices are found.
    • Add new devices: LED indicates the process of adding new devices.
    • Select device: LED indicates successful device selection.
    • Add device parameters: LED indicates the process of adding device parameters.
    • Finish settings: LED indicates successful completion of settings.
• FAQ:
  • Q1: How do I discard the SolarEdge Home Smart Switch?
  • A1: Discard this product according to local regulations or send it back to SolarEdge.
  • Q2: Where can I find additional resources and training for the SolarEdge products?
  • A2: You can find datasheets, training materials, and application notes on our website solaredge.com.

Safety Information and Handling

Safety Information

• For indoor use only
• Keep children away from the device
• DO NOT use with medical or life support equipment
• DO NOT use in wet area
• DO NOT clean with liquid
• Test the device locally for safe operation before attempting to control it remotely
• Use Copper conductors only
• Installation in a closed metal enclosure degrades wireless performance and must be avoided
• Discard this product according to local regulations or send it back to SolarEdge.
• Datasheet.
• Training.
• Application Note.

What’s in the package

Mounting Options

WARNING! Installation is allowed on up to 2000 meters of altitude

Cabling

Wiring

Pair with Inverter

LED Indications

Button Operation

• Press for <3 seconds to operate manually
• Hold >10 seconds to reset

LED Indications

• Blinking Blue – scanning for a network or connection with Home Network is lost & load off
• Blinking Green – scanning for a network or connection with Home Network is lost & load on
• Blinking Blue 30 seconds – received a request for identification
• Blue – connected to Home Network & load off
• Green – connected to Home Network & load on
• Blinking Red – error
• Flickering Blue – standby
• Flickering Green 5 times – reset done

Specifications

System Requirements

• Inverter with SolarEdge: Home Network wireless connection
• SolarEdge SetApp: smartphone application for connection to inverter and firmware >4.18.xx
• MySolarEdge: smartphone application for configuration and status reading
• iOS: 10 or later or Android 6.0.1 or later

CONTACT

• Support Contact Information
  • If you have technical problems concerning SolarEdge products, please contact us: https://www.solaredge.com/service/support.
  • Subject to change without notice.
  • Copyright © SolarEdge Inc.
  • All rights reserved. January 2023.
• About SolarEdge
  • SolarEdge is a global leader in smart energy technology.
  • By deploying world-class engineering capabilities and a relentless focus on innovation, we create smart energy products and solutions that power our lives and drive future progress.
  • solaredge.com.
  • © SolarEdge Technologies, Ltd.
  • All rights reserved.
  • Version: 1.1, October 2023
  • Subject to change without notice.
• Smart Switch
  • For inverters with SetApp configuration for ROW V 1.1