socket mobile D750 Barcode Scanner

This document pertains to the following 7Qi, 7Xi, D750:

INSTRUCTIONS: Scan command barcode(s) to quickly configure the barcode scanner.

•  Many of the command barcodes only work with a scanner in a particular Bluetooth mode as indicated by the header row of each table.
• Make sure the scanner is not connected to a host computer or device before scanning a  command barcode!

To use the scanner on multiple hosts, perform the unpair sequence.

1. Power on the scanner.
2. Press and hold down the trigger button.
3. Press and hold down the power button.
4. After you hear 3 beeps, release both buttons.

By default, the scanner is in Basic Mode (HID) as a Keyboard device.

For scanners in Application Mode (SPP) or Application Mode (MFi-SPP), you can alternatively config-ure some settings by using the Scanner Settings app. You can download the app from iTunes, and Google Play.

Factory Reset

Configures the scanner to revert all settings to factory defaults. The scanner powers off after scanning this barcode.

BLUETOOTH CONNECTION MODE

All Bluetooth connection modes OK.
Scan command barcode(s) to quickly configure the CHS. By default, the CHS is in HID mode as a Keyboard device.

IMPORTANT! Make sure the CHS is not connected to a host computer / device before scanning a command barcode!

Basic Mode (HID) (default)
Configures the CHS as a Keyboard class device (required for Apple iOS / Mac OS, Nokia E71).

HID-Peripheral
Configures the CHS as a Peripheral class device (optional for Windows and Android).

Application Mode (SPP)
Changes the CHS to Bluetooth Serial Port Profile (SPP) mode (optional for Windows and Android).

Application Mode (MFi-SPP)
Changes the CHS 7Qi, 7Xi, 7XiRx to Apple iOS mode (equivalent to SPP mode).

DATA SUFFIX

• All Bluetooth connection modes OK.
• You can configure the CHS to automatically add a suffix and/or prefix to each scan of data.
• Note: Scanning multiple commands in a single instance will overwrite (not append) the previous command.

Suffix – Carriage Return (default)
Configures the scanner to add a carriage return after decoded data.

Suffix – Tab
Configures the scanner to add a tab after decoded data

Suffix – Carriage Return & Line Feed
Configures the scanner to add a carriage return and line feed after decoded data.

Data As Is
Configures the scanner to return only the decoded data (i.e., no prefix or suffix).

RUMBLE/BEEP MODES

All Bluetooth connection modes OK.

•  Barcodes only work for 7Qi with Rev G and above. For Rev F and below refer to page 12.
• Barcodes only work for 7Xi with Rev Q and above. For Rev P and below refer to page 12.

Vibrate “On”
Enables scanner to vibrate to indicate successful scan

• Vibrate “Off”
  Disables scanner from vibrating to indicate successful scan
• Beep “On”
  Enables scanner to beep to indicate successful scan
• Beep “Off”
  Disables Scanner from beeping to indicate successful scans

HID KEYBOARD LANGUAGE SETTINGS

Scan only with scanner in Basic Mode (HID). Scan barcode to enable language.

English (Default)

French German Spanish

CHARGING STAND MODES

• All Bluetooth connection modes OK.
• Mobile Mode – Normal (default)*
• Scanning this bar code will enable the scanner to enter mobile mode. It will always be in manual trigger mode even when placed in the stand or cradle.
• Scanner Factory Reset returns to Mobile Mode.

Auto Mode (Presentation Mode)
Scanning this bar code will enable the scanner to enter auto mode. When the scanner is in auto mode, it will switch to presentation trigger mode when it detects power on the cradle pins. When the scanner is removed from the cradle it will remain in presentation trigger mode until the users presses the trigger. At that point it will switch to normal manual trigger mode. Auto Mode command barcode is also printed on the product label.

APPLE iOS ONSCREEN KEYBOARD

• Scan only with scanner in Basic Mode (HID).
• Apple iOS Onscreen Keyboard and Beep Enabled (Default)
• Configures the CHS to activate the iOS onscreen keyboard when connected to an iOS device and the CHS power button is double-pressed.

Disable both Onscreen Keyboard and Beep Enable Beep

Disable Beep

ADVANCED USERS ONLY

All Bluetooth Connection Modes OK.

•  Barcodes only work for 7Qi with Rev G and above. For Rev F and below refer to page 4.
• Barcodes only work for 7Xi with Rev Q and above. For Rev P and below refer to page 4.

Basic Mode (HID) (default)
Configures the scanner to Basic Mode (HID) Human Interface Device. The scanner will be discoverable as a Keyboard to other Bluetooth devices (required for Apple iOS, Mac OS, Nokia E71).

Basic Mode (HID) Keyboard (default)
Changes a scanner in HID-Peripheral mode to HID-Keyboard mode (required for Mac OS and Nokia E71, optional for Apple iOS).

Basic Mode (HID) Peripheral
Changes a scanner in HID-Keyboard mode to HID-Peripheral mode (optional for Windows and Android).

Application Mode (SPP)
Configures the scanner to Serial Port Profile (SPP) mode (optional for Windows and Android).

Application Mode (MFi-SPP)
Changes a scanner to Application Mode (MFi-SPP).
Required for Apple iOS applications developed with SocketScan 10 SDK.

BLUETOOTH CONNECTION MODE

Scan only with scanner in Application Mode (SPP) or Application Mode (MFi-SPP) Advanced users only.

Acceptor (default)
Configures the CHS to accept a Bluetooth connection puts the CHS in discoverable mode.

Initiator
Configures the CHS to initiate a connection to a computer / device with the Bluetooth Device Address specified in the barcode. The barcode must be formatted in Code 128 and contain the data

#FNIaabbccddeeff# such that    Bluetooth Device Address of the computer/device you want to connect to the CHS (required for Windows when using SPP mode). You must create a custom barcode for each computer / device that you want to connect to the CHS. Use barcode generating software or website (e.g., https://barcode.tec-it.com)

DATA MODE – FOR SPP MODE ONLY

Scan only with scanner in Application Mode (SPP) or Application Mode (MFi-SPP)
Advanced users only.

Packet Mode (default)
Configures the scanner to packet mode (i.e., the CHS encapsulates scan data into packets, with header and tail information to ensure integrity of data when received by host).

Raw Mode
Configures the scanner to raw mode (i.e., all scan data is sent as raw bytes instead of packets).

RUMBLE/BEEP MODES

• Scan only with scanner in Basic Mode (HID)
• Configures the scanner to Beep, Flash the LED Green, and Vibrate after successfully decoding data

Enable Beep and VibrateDisable Beep and Vibrate

#FNB 41FB990002#

Disable Vibrate

#FNB 41FB990003#

Disable Beep#FNB 41FB990006#

POWER BUTTON DOUBLE KEY PRESS

For Basic Mode (HID) only Scanner Engine Command Barcodes
Ctrl + Z
Scan to Enable WITH BEEP

#FNB4 1FBDA000C00060001010D000000000000#

Scan to Enable NO BEEP#FNB 41FBDA000C00020001011D000000000000#

Ctrl + A
Scan to Enable WITH BEEP#FNB 41FBDA000C000600010104000000000000#

Scan to Enable NO BEEP#FNB 41FBDA000C000200010104000000000000#

Shift + Tab
Scan to Enable WITH BEEP#FNB 41FBDA000C00060001202B000000000000#

Scan to Enable NO BEEP

#FNB 41FBDA000C00020001202B000000000000#

Ctrl + S
Scan to Enable WITH BEEP

Scan to Enable NO BEEP

#FNB 41FBDA000C000200010116000000000000#

2D INTERCHARACTER DELAY

Set Intercharacter delay to 5ms (default)#FNB41FBA70005#

Set Intercharacter Delay to 50ms

#FNB41FBA70032#

1D SYMBOLOGIES

Important! Print out page to scan. Do not scan on screen. *Default

Codabar
Scan to EnableScan to Disable

Code 93 / Code 93i
Scan to Enable

Scan to DisableInterleaved 2 of 5
Scan to EnableScan to Disable*EAN/UPC – UPC-E
Scan to EnableScan to Disable

*EAN/UPC – UPC-E
Scan to Enable

Scan to DisableEAN/UPC – UPC-E1
Scan to EnableScan to Disable*EAN/UPC – EAN 8
Scan to EnableScan to DisableStandard 2 of 5
Scan to EnableScan to Disable

GS1 DataBar (RSS)

• Scan to Enable
• Scan to Enable

*EAN/UPC – EAN-13
Scan to Enable

Scan to Disable

*Code 128 / GS1 128
Scan to Enable

Scan to Disable

*Code 39
Scan to Enable

Scan to DisableCode 11
Scan to Enable

Scan to Disable

2D SYMBOLOGIES

Important! Print out page to scan. Do not scan on screen. *Default

Aztec
Scan to EnableScan to Disable

*Data Matrix (Required to scan onscreen barcode in Socket EZ Pair for SPP mode)
Scan to Enable

Scan to Disable

MaxiCode
Scan to Enable

Scan to DisableQR Code
Scan to Enable

Scan to Disable

MicroPDF417
Scan to Enable

Scan to Disable

*PDF417
Scan to EnableScan to DisableGS1 Composite – CC-A/B
Scan to EnableScan to Disable

GS1 Composite – CC-C
Scan to EnableScan to Disable
GS1 DataBar (RSS) Limited

Scan to Enable
Scan to Disable
GS1 DataBar (RSS)
Scan to Enable

Scan to Disable

POSTAL SYMBOLOGIES

Important! Print out page to scan. Do not scan on screen. *Default

Australian Post
Scan to EnableScan to Disable

BPO 4-State
Scan to Enable

Scan to Disable

Canada Post
Scan to Enable

Scan to Disable

Dutch Post
Scan to EnableScan to Disable

Infomail
Scan to EnableScan to Disable

Japan Post
Scan to Enable

Scan to Disable

Planet
Scan to Enable

Scan to Disable

Postnet
Scan to Enable

Scan to Disable

Sweden Post
Scan to Enable

Scan to Disable

SCANNER MODES

Note: Scanning multiple commands in a single instance will overwrite (not append) the previous com-mand.

IMPORTANT! Print out page to scan. Do not scan on screen.
*Default

Aiming Beam
Makes an aiming beam appear when the scanner trigger button is pressed.

Scan to EnableScan to DisableCenter Decoding
When enabled, the scanner reads only the barcode that the scanner is aimed at. Helpful for barcodes positioned close together.

Scan to EnableScan to DisableDecode 1D Barcodes
Only Disables scanner from decoding 2D barcodes.

Scan to Enable

Scan to Disable

N/A

*Decode 1D and 2D Barcodes
Configures the scanner to revert all settings to factory defaults. The scanner wil power off after scanning this barcode.
Scan to Enable

Scan to Disable

Decode in Bright Environment
Enables the scanner to scan 1D and 2D barcodes in bright environment.

Scan to Enable

Scan to Disable

Decode on Reflective Surface
Enables the scanner to decode 1D and 2D barcodes printed on shiny surfaces

Scan to Enable

Documents / Resources

socket mobile D750 Barcode Scanner [pdf] Instruction Manual 7Qi, 7Xi, D750 Barcode Scanner, D750, Barcode Scanner, Scanner

References

• User Manual