ZALMAN i3 NEO ATX MID Tower Computer Case
Precautions
- Read this manual carefully before installing.
- Check the product and components before installing. If you find any abnormality, contact the location where you purchased the product for a replacement or refund.
- Wear gloves to prevent accidents when installing the product.
- Severe damage may occur when mounting the system, so do not apply excessive force.
- Connecting the cable incorrectly may cause a fire due to a short circuit. Make sure to refer to the manual when connecting the cable.
- Be careful not to block the ventilation hole of the product when using the system.
- Avoid locations with direct sunlight, water, moisture, oil, and excessive dust. Store and use the product in a well-ventilated location.
- Do not wipe the surface of the product using chemicals. (organic solvents such as alcohol or acetone)
- Do not insert your hand or other object into the product during operation, as this may injure your hand or damage the object.
- Store and use the product out of children’s reach.
- Our company assumes no responsibility for any problem that occurs due to the use of the product for purposes other than its designated purposes and/or the carelessness of the consumer.
- The exterior design and specifications of the product are subject to change without prior notice to consumers for quality improvement.
Specifications
| Model | i3 NEO | |
| Case Form Factor | ATX Mid-Tower | |
| Dimensions | 422 x 219 x 484(H)mm | |
| Weight | 5.6kg | |
| Case Materials | Plastic, Steel, Tempered Glass | |
| Motherboard Support | ATX / mATX / Mini-ITX | |
| Maximum VGA Length | 355mm | |
| Maximum CPU Cooler Height | 160mm | |
| Maximum PSU Length | 210mm | |
| PCI Expansion Slots | 7 | |
| Drive Bays | 2 x Combo (3.5″ or 2.5″, 1 x Toolless), 3 x SSD (2.5″) | |
|
Fan Support |
Top | 2 x 120mm / 2 x 140mm |
| Front | 3 x 120mm / 3 x 140mm | |
| Rear | 1 x 120mm | |
| Bottom | 2 x 120mm | |
| Fan(s) Included | Front | 3 x 120mm (With RGB LED Effect) |
| Rear | 1 x 120mm (With RGB LED Effect) | |
|
Radiator Support |
Top | 120mm / 240mm |
| Front | 120mm / 240mm / 280mm / 360mm | |
| Rear | 120mm | |
| I/O Ports | 1 x Headphones, 1 x MIC, 1 x USB2.0, 2 x USB3.0,
Reset Button, Power Button |
|
Accessories component
I/O Ports
- Removing the side panels
- Removing the front panel
- Mounting the motherboard
- Motherboard size
- Motherboard size
- Mounting PCI-E(VGA) card
- Mounting the 2.5″ SSD
- Mounting the 3.5″ and 2.5″ SSD / HDD
- Mounting the PSU
- Mounting the radiator
- Mounting the front radiator 120mm / 240mm / 280mm / 360mm
- Mounting the top radiator 120mm / 240mm
- Mounting the rear radiator 120mm
- Mounting the fans
- Mounting the top fans 2 x 120mm, 2 x 140mm
- Mounting the front fans 3 x 120mm, 3 x 140mm
- Mounting the rear/bottom fan 1 x 120mm / 2 x 120mm
- Fan(s) Included / Fan Specifications
- I/O Connectors
Documents / Resources
 |
ZALMAN i3 NEO ATX MID Tower Computer Case [pdf] User Manual i3 NEO, ATX MID Tower Computer Case, Tower Computer Case, Computer Case |
 |
ZALMAN i3 NEO ATX MID Tower Computer Case [pdf] User Manual i3 NEO, ATX MID Tower Computer Case, i3 NEO ATX MID Tower Computer Case, Tower Computer Case, Computer Case, Case |
