U-Prox SL maxi Keypad Best Versatile Reader
Specifications
- Product Name: U-PROX SL maxi
- Description: Adjustable universal SmartLine reader for mobile credentials and proximity identifiers
- Compatibility: Works with U-PROX ID application and mobile identifiers
Installation
- Make a small recess or hole (diameter 14 mm) to connect cable under the reader’s case.
- Loosen the screw at the bottom of the reader.
Connection
Seamless and easy connection to existing and new access systems through interfaces like Wiegand 26, 32, 34, 37, 40, 42, 56, 58, 64, 80 bits, RS232, and TouchMemory supports.
Recommended Cable: Multi-core signal cable with 0.22 mm² cross-section of each wire between the reader and panel.
Configuration
Adjust the reader completely with the free mobile application U-Prox Config, from indication to encryption modes.
Programming Password: Connect inputs D0 (green) and D1 (white) with each other and apply power to set the password.
Description
U-PROX SL maxi – the adjustable universal SmartLine reader for mobile credentials and proximity identifiers.
In conjunction with the U-PROX ID application and mobile identifiers U-PROX IDs allow any access control system to use smartphones as access system credentials.
Installation
- Make small recess or hole (diameter is 14 mm) to connect cable under the reader’s case
- Loosen the screw at the bottom of the reader
- Remove the top cover
- Carry out wiring to the control panel
- Mount the reader on the wall using supplied plastic dowels and screws
- Place the top cover and tighten it with a screw
Installation on the metal surfaces may cause decrease of reading range.
Do not place readers closer than 20 cm one from another. It is possible to install two readers at a distance 10-15 cm of each other when their yellow wires (Hold/Sync) interconnected. This synchronizes the work of the readers, they will work alternately.
Connection
Seamless and easy connection to existing and new access systems, due to the Wiegand 26, 32, 34, 37, 40, 42, 56, 58, 64, 80 bits interfaces, Wiegand with automatic selection, RS232 and TouchMemory supports.
We recommend to use multi-core signal cable with 0.22 mm2 cross-section of each wire between reader and panel.
Wiegand
The reader connection wires functions are listed in the table.
We recommended to use following whiring when reader connected to the control panel with twisted pair.
The reader connection wires functions are listed in the table.
TouchMemory
The reader connection wires functions are listed in the table.
We recommended to use following whiring when reader connected to the control panel with twisted pair.
Configuration
With the free mobile application U-Prox Config, the reader can be completely adjusted — from the indication to the encryption modes.
The reader is supplied without the engineering password for programming specified. To connect and (re) set the password — connect inputs D0 (green) and D1 (white) with each other and apply power to the reader.
The reader firmware can be updated with an NFC-enabled Android smartphone only.
Mobile identification
Reader supports digital personal mobile credential. It is processed and stored in the user’s smartphone using the U-PROX ID application. It can be transferred over NFC and/or 2.4 GHz radio between the reader and the smartphone.
Reader supports hardware active mobile identifiers U-PROX Tag and U-PROX Auto Tag.
Reader supports 3 operation modes for smartphones with U-Prox ID:
- “Door-Proximity” – 10-20 cm, reader activates by built-in proximity sensor. Recommended for double-sided doors and turnstiles
- “Door” – up to 60-70 cm
- “Barrier/Gate” – adjustable range of interaction from 1 to 15 m.
U-PROX ID application
Free mobile application U-PROX ID receives, stores and transmits mobile credentials between the reader and the smartphone.
How to obtain mobile ID
You can purchase mobile IDs from our dealers
RFID, 125 kHz
The reader supports 125 kHz cards with amplitude (ASK – EmMarine, etc.) and frequency modulation (FSK – Temik, etc.)
These cards do not have cloning protection, but are very popular due to their low cost
Mifare® identifiers
The reader supports work with Mifare® cards, reads encrypted identifiers with a user-assigned card number, with a static or diversified encryption key.
Up to five encryption profiles can be used simultaneously.
Mifare®Classic
The least secure series of cards, has a Crypto 1 (SL1) encryption algorithm vulnerability.
When using it, it is recommended to encrypt all card sectors with a diversified encryption key.
Mifare®Plus
The reader supports SL1 and SL3 modes for Mifare®Plus. It is recommended to use SL3 mode as it has the highest security and AES encryption algorithm.
Mifare®Defire
The reader supports Mifare DESFire EV1, EV2 and EV3 cards. AES encryption algorithm is supported.
Warranty
Warranty for U-PROX devices (except batteries) is valid for two years after the purchase date. If the device operates incorrectly, please contact support@u-prox.systems at first, maybe it can be solved remotely.
FAQ
How can I obtain mobile ID?
You can purchase mobile IDs from our dealers.
Documents / Resources
 |
U-Prox SL maxi Keypad Best Versatile Reader [pdf] Instruction Manual SL maxi Keypad Best Versatile Reader, SL maxi, Keypad Best Versatile Reader, Versatile Reader |