truflo-logo

truffle TI3P Series Insertion Paddle Wheel Flow Meter Sensor

truflo-TI3P-Series-Insertion-Paddle-Wheel-Flow-Meter-Sensor-product

Specifications

  • Operating Range: 0.1 to 10 m/s
  • Pipe Size Range: DN15 to DN600
  • Linearity: High-precision
  • Repeatability: Accurate and reliable
  • Wetted Materials: PVC, PP, PVDF, 316SS, FKM, EPDM, FFKM
  • Electrical Frequency: 49 Hz per m/s nominal, 15 Hz per ft/s nominal
  • Supply Voltage: Standard voltage
  • Supply Current: Low power consumption

Safety Information

truflo-TI3P-Series-Insertion-Paddle-Wheel-Flow-Meter-Sensor-fig- (7)

  • De-pressurize and vent the system before installation or removal
  • Confirm chemical compatibility before use
  • DO NOT exceed maximum temperature or pressure specifications
  • ALWAYS wear safety goggles or face-shield during installation and/or service
  • DO NOT alter product construction

truflo-TI3P-Series-Insertion-Paddle-Wheel-Flow-Meter-Sensor-fig- (1) Warning | Caution | Danger
Indicates a potential hazard. Failure to follow all warnings may lead to equipment damage, injury, or death.

truflo-TI3P-Series-Insertion-Paddle-Wheel-Flow-Meter-Sensor-fig- (2) Note | Technical Notes
Highlights additional information or detailed procedure.

truflo-TI3P-Series-Insertion-Paddle-Wheel-Flow-Meter-Sensor-fig- (3) Hand Tighten Only
Over-tightening may permanently damage product threads and lead to the failure of the retaining nut.

truflo-TI3P-Series-Insertion-Paddle-Wheel-Flow-Meter-Sensor-fig- (4) Do Not Use Tools
Use of tools) may damage produced beyond repair and potentially void product warranty.

truflo-TI3P-Series-Insertion-Paddle-Wheel-Flow-Meter-Sensor-fig- (5) Personal Protective Equipment (PPE)
Always utilize the most appropriate PPE during the installation and service of Truflo® products.

truflo-TI3P-Series-Insertion-Paddle-Wheel-Flow-Meter-Sensor-fig- (6) Pressurized System WarningThe sensor may be under pressure. Take caution to vent the system before installation or removal. Failure to do so may result in equipment damage and/or serious injury.

Product Description

truflo-TI3P-Series-Insertion-Paddle-Wheel-Flow-Meter-Sensor-fig- (8)

The TI Series insertion plastic paddle wheel flow meter has been engineered to provide long-term accurate flow measurement in tough industrial applications. The paddle wheel assembly consists of an engineered Tefzel® paddle and micro-polished zirconium ceramic rotor pin and bushings. High-performance Tefzel® and Zirconium materials have been selected due to their excellent chemical and wear-resistant properties.

Features

  • ½” – 24″ Line Sizes
  • Flow Rate | Total
  • Pulse | RS485 Outputs (Optional)

New ShearPro® Design

truflo-TI3P-Series-Insertion-Paddle-Wheel-Flow-Meter-Sensor-fig- (9)

  • Contoured Flow Profile
  • Reduced Turbulence = Increased Longevity
  • 78% Less Drag than Old Flat Paddle Design

Tefzel® Paddle Wheel

truflo-TI3P-Series-Insertion-Paddle-Wheel-Flow-Meter-Sensor-fig- (10)

  • Superior Chemical And Wear Resistance vs PVDF

Zirconium Ceramic Rotor | Bushings

truflo-TI3P-Series-Insertion-Paddle-Wheel-Flow-Meter-Sensor-fig- (11)truflo-TI3P-Series-Insertion-Paddle-Wheel-Flow-Meter-Sensor-fig- (12)

  • Up to 15x the Wear Resistance
  • Integral Rotor Bushings Reduce Wear and Fatigue Stress

360° Shielded Rotor Design

truflo-TI3P-Series-Insertion-Paddle-Wheel-Flow-Meter-Sensor-fig- (13)

  • Eliminates Finger Spread
  • No Lost Paddles

Technical Specifications

truflo-TI3P-Series-Insertion-Paddle-Wheel-Flow-Meter-Sensor-fig- (14)truflo-TI3P-Series-Insertion-Paddle-Wheel-Flow-Meter-Sensor-fig- (15)truflo-TI3P-Series-Insertion-Paddle-Wheel-Flow-Meter-Sensor-fig- (16)truflo-TI3P-Series-Insertion-Paddle-Wheel-Flow-Meter-Sensor-fig- (17)truflo-TI3P-Series-Insertion-Paddle-Wheel-Flow-Meter-Sensor-fig- (18)truflo-TI3P-Series-Insertion-Paddle-Wheel-Flow-Meter-Sensor-fig- (19)truflo-TI3P-Series-Insertion-Paddle-Wheel-Flow-Meter-Sensor-fig- (20)truflo-TI3P-Series-Insertion-Paddle-Wheel-Flow-Meter-Sensor-fig- (21)

See Temperature and Pressure Graphs for more information

Model Selection

truflo-TI3P-Series-Insertion-Paddle-Wheel-Flow-Meter-Sensor-fig- (22)

Add Suffix

  • ‘E’ – EPDM Seals
  • ‘R’ – RS485 Communication Output – $100

truflo-TI3P-Series-Insertion-Paddle-Wheel-Flow-Meter-Sensor-fig- (23)

Add Suffix

  • ‘E’ – EPDM Seals
  • ‘R’ – RS485 Communication Output – $100

Display Characteristics

truflo-TI3P-Series-Insertion-Paddle-Wheel-Flow-Meter-Sensor-fig- (24)

Dimensions (mm)

truflo-TI3P-Series-Insertion-Paddle-Wheel-Flow-Meter-Sensor-fig- (25)truflo-TI3P-Series-Insertion-Paddle-Wheel-Flow-Meter-Sensor-fig- (26)

Wiring Diagram

truflo-TI3P-Series-Insertion-Paddle-Wheel-Flow-Meter-Sensor-fig- (27)truflo-TI3P-Series-Insertion-Paddle-Wheel-Flow-Meter-Sensor-fig- (28)

Wiring – SSR* (Totalizer)

truflo-TI3P-Series-Insertion-Paddle-Wheel-Flow-Meter-Sensor-fig- (29)Set “Con n” in Pulse Output Control (Refer Pulse Control Programming, Page 11)

Wiring – One Pulse/Gal | Con E

truflo-TI3P-Series-Insertion-Paddle-Wheel-Flow-Meter-Sensor-fig- (30)Set “Con E” in Pulse Output Control (Refer Pulse Control PProgramming Page 11)

Wiring – SSR* (Flow Rate)

truflo-TI3P-Series-Insertion-Paddle-Wheel-Flow-Meter-Sensor-fig- (31)Set any “Con” in Pulse Output Control (Refer Pulse Control PrProgrammingPage 11)

Wiring – To Flow Display | Con F

truflo-TI3P-Series-Insertion-Paddle-Wheel-Flow-Meter-Sensor-fig- (32)Set “Con F” in Pulse Output Control (Refer to Pulse Control ProProgrammingage 11)

Installation

truflo-TI3P-Series-Insertion-Paddle-Wheel-Flow-Meter-Sensor-fig- (34)truflo-TI3P-Series-Insertion-Paddle-Wheel-Flow-Meter-Sensor-fig- (35)truflo-TI3P-Series-Insertion-Paddle-Wheel-Flow-Meter-Sensor-fig- (36)truflo-TI3P-Series-Insertion-Paddle-Wheel-Flow-Meter-Sensor-fig- (37)truflo-TI3P-Series-Insertion-Paddle-Wheel-Flow-Meter-Sensor-fig- (38)Very Important

  • Lubricate O-rings with a viscous lubricant, compatible with the materials of construction.
  • Using an alternating | twisting motion, carefully lower the sensor into the fitting. | Do Not Force | Fig-3
  • Ensure tab | notch is called to flow direction | Fig-4

truflo-TI3P-Series-Insertion-Paddle-Wheel-Flow-Meter-Sensor-fig- (33) Hand HaHand-tighten sensor. DO NOT use any tools on the sensor cap or the cap threads or fitting threads may be damaged. | Fig-5

Correct Sensor Position

  1. Locate the flow meter positioning tab and clamp the saddle notch.truflo-TI3P-Series-Insertion-Paddle-Wheel-Flow-Meter-Sensor-fig- (39)
  2. Engage one thread of the sensor cap, then turn the sensor until the alignment tab is seated in the fitting notch. Ensure the tab is parallel to the flow direction.truflo-TI3P-Series-Insertion-Paddle-Wheel-Flow-Meter-Sensor-fig- (40)
  3. Hand tighten using the retention captruflo-TI3P-Series-Insertion-Paddle-Wheel-Flow-Meter-Sensor-fig- (41)
    • Hand-tighten the screw cap
    • DO NOT use any tools — threads may be damaged
    • Ensure the meter is firmly in place

Correct Sensor Position Setup

truflo-TI3P-Series-Insertion-Paddle-Wheel-Flow-Meter-Sensor-fig- (42)TI Series flow meters measure liquid media only. There should be no air bubbles and the pipe must always remain full. To ensure accurate flow measurement, the placement of the flow meters needs to adhere to specific parameters. This requires a straight run pipe with a minimum number of pipe diameters distance upstream and downstream of the flow sensor.

Flange

truflo-TI3P-Series-Insertion-Paddle-Wheel-Flow-Meter-Sensor-fig- (43)

2x 90° Elbow

truflo-TI3P-Series-Insertion-Paddle-Wheel-Flow-Meter-Sensor-fig- (44)

Reducer

truflo-TI3P-Series-Insertion-Paddle-Wheel-Flow-Meter-Sensor-fig- (45)

90° Downward Flow

truflo-TI3P-Series-Insertion-Paddle-Wheel-Flow-Meter-Sensor-fig- (46)

90° Elbow Downward Flow Upward

truflo-TI3P-Series-Insertion-Paddle-Wheel-Flow-Meter-Sensor-fig- (47)

Ball Valve

truflo-TI3P-Series-Insertion-Paddle-Wheel-Flow-Meter-Sensor-fig- (48)

Installation Positions

truflo-TI3P-Series-Insertion-Paddle-Wheel-Flow-Meter-Sensor-fig- (49)

  1. Good if NO SEDIMENT presenttruflo-TI3P-Series-Insertion-Paddle-Wheel-Flow-Meter-Sensor-fig- (50)
  2. Good if NO AIR BUBBLES presenttruflo-TI3P-Series-Insertion-Paddle-Wheel-Flow-Meter-Sensor-fig- (51)
  3. Preferred installation if SEDIMENT* or AIR BUBBLES may be present

Fittings and K-Factor

truflo-TI3P-Series-Insertion-Paddle-Wheel-Flow-Meter-Sensor-fig- (57)

TEE FITTINGS

truflo-TI3P-Series-Insertion-Paddle-Wheel-Flow-Meter-Sensor-fig- (52)

CLAMP-ON SADDLES

truflo-TI3P-Series-Insertion-Paddle-Wheel-Flow-Meter-Sensor-fig- (53)

CPVC SOCKET WELD-ON ADAPTERS

truflo-TI3P-Series-Insertion-Paddle-Wheel-Flow-Meter-Sensor-fig- (54)

TEE FITTINGS (V2)

truflo-TI3P-Series-Insertion-Paddle-Wheel-Flow-Meter-Sensor-fig- (55)

Pressure vs. Temperature

truflo-TI3P-Series-Insertion-Paddle-Wheel-Flow-Meter-Sensor-fig- (56)

Note: During system design the specifications of all components must be considered. I Non-Shock

Min/Max Flow Rates

truflo-TI3P-Series-Insertion-Paddle-Wheel-Flow-Meter-Sensor-fig- (58)

Programming

truflo-TI3P-Series-Insertion-Paddle-Wheel-Flow-Meter-Sensor-fig- (59)

truflo-TI3P-Series-Insertion-Paddle-Wheel-Flow-Meter-Sensor-fig- (60)

Setting Output Limits (SSR*)

truflo-TI3P-Series-Insertion-Paddle-Wheel-Flow-Meter-Sensor-fig- (61)

Pulse Control Programming

truflo-TI3P-Series-Insertion-Paddle-Wheel-Flow-Meter-Sensor-fig- (62)

Alarm Mode Selection

truflo-TI3P-Series-Insertion-Paddle-Wheel-Flow-Meter-Sensor-fig- (63)

Totalizer Reset

truflo-TI3P-Series-Insertion-Paddle-Wheel-Flow-Meter-Sensor-fig- (64)

Rotor Pin | Paddle Replacement

truflo-TI3P-Series-Insertion-Paddle-Wheel-Flow-Meter-Sensor-fig- (65)truflo-TI3P-Series-Insertion-Paddle-Wheel-Flow-Meter-Sensor-fig- (66)truflo-TI3P-Series-Insertion-Paddle-Wheel-Flow-Meter-Sensor-fig- (67)

Installation Fittings

SA Clamp-On Saddle Fittings

  • truflo-TI3P-Series-Insertion-Paddle-Wheel-Flow-Meter-Sensor-fig- (68) PVC Material
  • Viton® O-Rings
  • Available in Metric DIN
  • Will Accept Signet® Type Flow Meter

truflo-TI3P-Series-Insertion-Paddle-Wheel-Flow-Meter-Sensor-fig- (69)

PT | PPT | PFT Installation Fittings

  • truflo-TI3P-Series-Insertion-Paddle-Wheel-Flow-Meter-Sensor-fig- (70) PVC | PP | PVDF
  • Socket End Connections
  • Will Accept Signet® Type Flow Meter
  • True-Union Design

truflo-TI3P-Series-Insertion-Paddle-Wheel-Flow-Meter-Sensor-fig- (71)

Add Suffix

  • ‘E’ – EPDM Seals
  • T’ – NPT End Connectors
  • ‘B’ – Butt Fused End Connections for PP or PVDF

SAR Clamp-On Saddle Fittings (SDR Pipe)

truflo-TI3P-Series-Insertion-Paddle-Wheel-Flow-Meter-Sensor-fig- (72)

  • PVC Material
  • Viton® O-Rings
  • Available in Metric DIN
  • Will Accept Signet® Type Flow Meter

truflo-TI3P-Series-Insertion-Paddle-Wheel-Flow-Meter-Sensor-fig- (73)

СТ CPVC Tee Installation Fitting

truflo-TI3P-Series-Insertion-Paddle-Wheel-Flow-Meter-Sensor-fig- (74)

  • 1″-4″ Pipe Sizes
  • Easy to Install
  • Will Accept Signet® Flow Meter

truflo-TI3P-Series-Insertion-Paddle-Wheel-Flow-Meter-Sensor-fig- (75)

Add Suffix

  • ‘E’ – EPDM Seals
  • ‘T’ – NPT End Connectors
  • ‘B’ – Butt Fused End Connections for PP or PVDF

PG Glue-On Adapter

  • truflo-TI3P-Series-Insertion-Paddle-Wheel-Flow-Meter-Sensor-fig- (76) 2″-24″ Pipe Sizes
  • Easy to Install
  • Will Accept Signet® Flow Meter

truflo-TI3P-Series-Insertion-Paddle-Wheel-Flow-Meter-Sensor-fig- (77)

SWOL Weld-On Adapter

  • truflo-TI3P-Series-Insertion-Paddle-Wheel-Flow-Meter-Sensor-fig- (78) 2″-12″ Pipe Sizes
  • 316SS Weld-o-let with PVDF insert
  • Easy to Install
  • Will Accept Signet® Flow Meter

truflo-TI3P-Series-Insertion-Paddle-Wheel-Flow-Meter-Sensor-fig- (79)

SST 316SS TI3 Series NPT Tee Fittings

  • truflo-TI3P-Series-Insertion-Paddle-Wheel-Flow-Meter-Sensor-fig- (80) Will Accept Signet® Type Flow Meter

truflo-TI3P-Series-Insertion-Paddle-Wheel-Flow-Meter-Sensor-fig- (81)

SSS 316SS TI3 Series Sanitary Tee Fittings

  • truflo-TI3P-Series-Insertion-Paddle-Wheel-Flow-Meter-Sensor-fig- (82) Will Accept Signet® Type Flow Meter

truflo-TI3P-Series-Insertion-Paddle-Wheel-Flow-Meter-Sensor-fig- (83)

SSF 316SS TI3 Series Flanged Tee Fittings

  • truflo-TI3P-Series-Insertion-Paddle-Wheel-Flow-Meter-Sensor-fig- (84) Will Accept Signet® Type Flow Meter

truflo-TI3P-Series-Insertion-Paddle-Wheel-Flow-Meter-Sensor-fig- (85)

Warranty, Returns, and Limitations

Warranty
Icon Process Controls Ltd warrants to the original purchaser of its products that such products will be free from defects in material and workmanship under normal use and service under instructions furnished by Icon Process Controls Ltd for one year from the date of sale of such products. Icon Process Controls Ltd’s obligation under this warranty is solely and exclusively limited to the repair or replacement, at Icon Process Controls Ltd’s option, of the products or components, that Icon Process Controls Ltd examination determines to its satisfaction to be defective in material or workmanship within the warranty period. Icon Process Controls Ltd must be notified under the instructions below of any claim under this warranty within thirty (30) days of any claimed lack of conformity of the product. Any product repaired under this warranty will be warranted only for the remainder of the original warranty period. Any product provided as a replacement under this warranty will be warranted for one year from the date of replacement.

Returns
Products cannot be returned to Icon Process Controls Ltd without prior authorization. To return a product that is thought to be defective, go to www.iconprocon.com, submit a customer return (MRA) request form, and follow the instructions therein. All warranty and non-warranty product returns to Icon Process Controls Ltd must be shipped prepaid and insured. Icon Process Controls Ltd will not be responsible for any products lost or damaged in shipment.

Limitations
This warranty does not apply to products which:

  1. are beyond the warranty period or are products for which the original purchaser does not follow the warranty procedures outlined above;
  2. have been subjected to electrical, mechanical,l or chemical damage due to improper, accidental, or negligent use;
  3. have been modified or altered;
  4. anyone other than service personnel authorized by Icon Process Controls Ltd have attempted to repair;
  5. have been involved in accidents or natural disasters; or
  6. are damaged during return shipment to Icon Process Controls Lt

Icon Process Controls Ltd reserves the right to unilaterally waive this warranty and dispose of any product returned to Icon Process Controls Ltd where: T there is evidence of a potentially hazardous material present with the product;

  1. Or the product has remained unclaimed at Icon Process Controls Ltd for more than 30 days after Icon Process Controls Ltd has dutifully requested disposition.

This warranty contains the sole express warranty made by Icon Process Controls Ltd in connection with its products. ALL IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION, THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE EXPRESSLY DISCLAIMED. The remedies of repair or replacement as stated above are the exclusive remedies for the breach of this warranty. IN NO EVENT SHALL Icon Process Controls Ltd BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY KIND INCLUDING PERSONAL OR REAL PROPERTY OR FOR INJURY TO ANY PERSON THIS WARRANTY CONSTITUTES THE FINAL, COMPLETE, AND EXCLUSIVE STATEMENT OF WARRANTY TERMS AND NO PERSON IS AUTHORIZED TO MAKE ANY OTHER WARRANTIES OR REPRESENTATIONS ON BEHALF OF Icon Process Controls Ltd. This warranty will be interpreted under the laws of the province of Ontario, Canada. If any portion of this warranty is held to be invalid or unenforceable for any reason, such finding will not invalidate any other provision of this warranty.

For additional product documentation and technical support visit:
www.iconprocon.com
e-mail: sales@iconprocon.com
support@iconprocon.com
Ph: 905.469.9283

FAQs

Q: How do I confirm chemical compatibility before use?
A: Check the user manual or contact the manufacturer for a list of compatible chemicals with the materials used in the sensor.

Q: What should I do if I exceed the maximum temperature or pressure specifications?
A: Stop using the sensor immediately and consult with a professional for inspection and potential adjustments to avoid equipment damage.

Q: Can I use this sensor with different pipe sizes?
A: The sensor is compatible with a range of pipe sizes from DN15 to DN600 within the specified operating range.

Documents / Resources

truflo TI3P Series Insertion Paddle Wheel Flow Meter Sensor [pdf] Owner's Manual
TI3P Series Insertion Paddle Wheel Flow Meter Sensor, TI3P Series, Insertion Paddle Wheel Flow Meter Sensor, Paddle Wheel Flow Meter Sensor, Wheel Flow Meter Sensor, Meter Sensor
truflo TI3P Series Insertion Paddle Wheel Flow Meter Sensor [pdf] Owner's Manual
TI3P 316 SS, TI3P Series Insertion Paddle Wheel Flow Meter Sensor, TI3P Series, Insertion Paddle Wheel Flow Meter Sensor, Paddle Wheel Flow Meter Sensor, Wheel Flow Meter Sensor, Flow Meter Sensor, Meter Sensor

References

Leave a comment

Your email address will not be published. Required fields are marked *