18-BC113D1-1C-EN Integrated Variable or Multi Speed Control Drive Replacement
Product Information
Specifications:
- Model: 18-BC113D1-1C-EN
- Product Type: Integrated Variable or Multi Speed Control Drive
Replacement - Voltage: 400VDC
- Features: Thermal Grease Application, Safety Precautions, Drive
Test Points
Product Usage Instructions
Section 1. Safety
Only qualified personnel should install and service the
equipment. Follow all safety precautions mentioned in the
literature and on equipment tags, stickers, and labels.
Section 2. Tools and Parts Required
Ensure you have the necessary tools as listed in the manual
before proceeding with the installation or replacement.
Section 3. Terminology
Understand the terminology used in the manual to effectively
carry out the procedures. Familiarize yourself with terms like
Drive, Drive Assembly, EEV, HPCO, IVSC, PM, and IMSC.
Section 4. Remove Drive
- Disconnect all electric power sources including remote
disconnects. - Follow proper lockout/tagout procedures to prevent accidental
energizing of power. - Remove the Drive carefully ensuring no damage is caused to
surrounding components.
Section 5. Apply Thermal Grease
Apply thermal grease as instructed in the manual to ensure
proper heat dissipation.
Section 6. Reinstall the Drive
- Secure the Drive back into place following the reverse steps of
removal. - Ensure all connections are properly reattached.
- Double-check for any loose components before turning on
power.
Section 7. Perform Final Inspection
Before powering on the equipment, conduct a final inspection to
verify proper installation and connections.
Section 8. Return Drive Board
If any drive boards were removed during the process, ensure they
are returned to their original positions securely.
FAQ (Frequently Asked Questions)
Q: What should I do if I encounter a hot surface
warning?
A: If you come across a hot surface warning,
avoid touching the compressor to prevent burns and potential
injury.
Q: How important is grounding in the installation
process?
A: Grounding is crucial to prevent equipment
damage and personal injury. Ensure all grounding devices are
inspected and properly used during installation.
18-BC113D1-1C-EN
Installer’s Guide
Integrated Variable or Multi Speed Control Drive Replacement
ALL phases of this installation must comply with NATIONAL, STATE AND LOCAL CODES IMPORTANT — These instructions do not cover all variations in systems, nor do they provide for every possible contingency to be met in connection with the installation. Should further information be desired, or should particular problems arise which are not sufficiently covered for the purchaser’s purposes, the matter should be referred to your installing dealer or local distributor. IMPORTANT — Please ensure correct drive is used as replacement. This can be verified by the drive label color and unit tonnage. 2-3T Variable Speed: Replace with Green or Pink labeled drive 4-5T Variable Speed: Replace with Pink labeled drive ONLY 2-5T Multi Speed: Replace with Orange labeled drive ONLY IMPORTANT — Do not replace the AOC only.This replacement drive comes with an AOC and MOC, and they must stay together as an assembly to ensure firmware compatibility between the two.
Table of Contents
Section 1. Safety …………………………………….. 2 Section 2. Tools and Parts Required ………….. 3 Section 3. Terminology …………………………….. 3 Section 4. Remove Drive………………………….. 4 Section 5. Apply Thermal Grease………………. 6 Section 6. Reinstall the Drive ……………………. 7 Section 7. Perform Final Inspection……………. 7 Section 8. Return Drive Board…………………… 7
Section 1. Safety
Only qualified personnel should install and service the equipment. The installation, starting up, and servicing of heating, ventilating, and air-conditioning equipment can be hazardous and requires specific knowledge and training. Improperly installed, adjusted or altered equipment by an unqualified person could result in death or serious injury. When working on the equipment, observe all precautions in the literature and on the tags, stickers, and labels that are attached to the equipment.
WARNING
HAZARDOUS VOLTAGE! Failure to follow this Warning could result in property damage, severe personal injury, or death. Disconnect all electric power, including remote disconnects before servicing. Follow proper lockout/tagout procedures to ensure the power cannot be inadvertently energized.
WARNING
HIGH LEAKAGE CURRENT! Failure to follow this warning could result in property damage, severe personal injury, or death. Earth connection essential before connecting supply.
CAUTION
GROUNDING REQUIRED! Failure to inspect or use proper service tools may result in equipment damage or personal injury. Reconnect all grounding devices. All parts of this product that are capable of conducting electrical current are grounded. If grounding wires, screws, straps, clips, nuts, or washers used to complete a path to ground are removed for service, they must be returned to their original position and properly fastened.
CAUTION
HOT SURFACE! May cause minor to severe burning. Failure to follow this Caution could result in property damage or personal injury. Do not touch compressor.
2
18-BC113D1-1C-EN
400 VOLTS
ELECTRICAL HAZARD
Failure to follow this warning could result in personal injury or death.
WAIT TWO (2) MINUTES after disconnecting power prior to touching electrical components as they may hold a dangerous charge of 400VDC, then verify DC Voltage is less than 42 VDC at inverter test points labeled +DC and -DC before servicing board.
DC- DC+
+DC -DC
+DC and -DC
Figure 1 – Drive Test Points
Section 2. Tools and Parts Required
2.1 – Tools Required The following tools are required to perform the procedures described in this document:
· DC Volt Meter · 5/16″ Nut Driver · 7/16″ Socket Wrench · Torque Wrench w/ 7/16″ Socket 2.2 – Parts Required All required parts are contained in the Replacement Kit that accompanies this document. They include:
· Thermal Grease · Aluminum Nuts (3) – These Aluminum Nuts
secure the Cold Plate to the Drive assembly. These are spares and should be used in the event of damage to the ones installed on the Unit. Verify that you have the required tools and parts before proceeding.
Section 3. Terminology
The following terms and abbreviations are used in this document.
Drive ………………………………………….same as MOC Drive Assembly ……………. same as AOC and MOC EEV ……………………….. Electronic Expansion Valve HPCO ……………………………..High Pressure Cut Off IVSC ………………Integrated Variable Speed Control PM…………………………………….. Personality Module IMSC…………………. Integrated Multi Speed Control
18-BC113D1-1C-EN
3
Replacement Drive
Section 4. Remove Drive
4.1 – Power Down Unit and Remove Cover 1. Power down the Outdoor Unit and wait at least 2
minutes. 2. Remove the 4 screws securing the Control Box
cover and place screws and cover aside (See “Figure 2 – Outdoor Unit”).
Control Box Cover
Remove these 4 Screws
and Control Box Cover
The original drive in unit may have ferrite harnesses attached to HPCO leads, fan motor or compressor harness. Please re-use these as the replacement drive in this kit does not come with additional ferrites.
3. Unplug all AOC connectors located at the top of the drive and move the leads aside.
Variable Speed Drives
You will unplug these connectors from the AOC (See “Figure 4 – IVSC Connections”):
· Latching Switchover Valve J17 · EEV J5 · CAN J20 · Ambient Temperature J21 · Discharge Temperature J22 · Coil Temperature J23 · Suction Temperature J24 · Liquid Temperature J25 · Suction Pressure J26 · Liquid Pressure J27 · Personality module J16
DS51 Yellow – COMM J14, J15 Charge
Assistance J7
SAT Temp J19
Data Port
J8 AOC/MOC Interface
Program Socket FRC DFT Load Shed
J26 J27 Suc P Liq P Sensor Sensor
Sensor Sensor Sensor Sensor Sensor
AMB Dis T Coil T Suc T Liq T
J25
J23 J24
Figure 2 – Outdoor Unit
3. Test voltage across Inverter test points (see “Figure 1 – Drive Test Points on page 3.”) WARNING – DO NO PROCEED until DC voltage measures less than 42 VDC.
4.2 – Remove Connections 1. Remove the ground wire (see “Figure 3 – Compressor
Connections”) located at the bottom of the Drive. 2. Disconnect the harness.
Disconnect Compressor Harness
Remove Ground Wire
J16
J11
S 6
J2, J3
PM
J17 LSOV
J5 EEV J20 CAN
Figure 4 – IVSC Connections
J22
J21
Figure 3 – Compressor Connections
4
18-BC113D1-1C-EN
Multiple Speed Drives
You will unplug these connectors from the AOC (See “Figure 5 – IMSC Connections”):
· Latching Switchover Valve (LSOV) J17 · Electronic Expansion Valve (EEV) J5 · Ambient Temperature (AMB) J21 · Discharge Temperature (Dis_T) J22 · Coil temperature (Coil_T) J23 · 24 VAC Thermostat Control J4 · Personality Module J16
Replacement Drive
Disconnect high voltage field connections. Use care when removing the connectors. Some have latching tabs that must be depressed while removing. DO NOT PULL ON WIRES. Grasp by connector only when removing plug from board.
AOC Board
Unplug the HPCO wires
Figure 6 – MOC Drive Connections
4.3 – Remove the Cold Plate 1. Remove the three Aluminum nuts securing the Cold
Plate to the Drive Assembly (See “Figure 7 – Drive Cold Plate”) and set aside. You will use a Torque Wrench when reattaching Cold Plate to Drive.
2. Remove the Cold Plate and set aside. Avoid direct contact with the Thermal Grease that is exposed when the Plate is removed.
3. Separate the Liquid Line from the Drive Assembly one to two inches. Be careful not to bend or strain the copper tubing.
Figure 5 – IMSC Connections
Unplug the HPCO wires, fan harness and compressor harness from the MOC (See Figure 6 MOC Drive Connections).
Remove Aluminum
Nut
IVSC Cold Plate
Remove Aluminum
Nuts
18-BC113D1-1C-EN
Figure 7 – Drive Cold Plate
5
Replacement Drive
4. Using a clean, dry cloth carefully wipe away any existing thermal grease from the copper tubes. Support the tubing at all times and take care not to bend or twist the tubing.
4.4 – Remove the Drive 1. Remove the screws securing the drive in place
(See “Figure 8 – Drive Screw Locations”). When removing the final screw, support the drive with one hand.
USE CARE AND DO NOT ALLOW THE DRIVE TO SLIP AND DAMAGE THE LIQUID LINE.
2. Remove the drive by sliding it up and away from the cabinet housing.
Section 5. Apply Thermal Grease
To apply the Thermal Grease, the drive should be positioned so that the plastic cover is facing down and the cutout for the Liquid Line is facing up.
It is critical that the copper Liquid Line has good thermal contact with the aluminum plate. Proper application of Thermal Grease will ensure this contact.
Apply a small, 1/8″ bead of Thermal Grease in the center of the cutout around the entire length. It takes very little grease to create adequate thermal transfer. The included .5-ounce tube contains enough grease for 2-3 applications. See Heat Sink Detail.
Remove this screw last and support Drive while removing
Remove these
screws first
2 1
Slide Drive up and away to remove
Figure 8 – Drive Screw Locations
Thermal Grease Fill Line
HEAT SINK DETAIL
1/8″ Grease Bead
6
18-BC113D1-1C-EN
Replacement Drive
Section 6. Reinstall the Drive
6.1 – Return the Drive to the Cabinet Housing 1. Place the Drive back in its original position by
sliding it between the Liquid Line and the cabinet housing.
2. While holding the Drive firmly against the cabinet with one hand, replace the top right screw first. Tighten this screw by hand, enough to secure the Drive to the cabinet but still allow the Drive to move.
3. Verify that all wiring harnesses and wires are out of the way and that none of them are pinched between the Drive and cabinet housing.
4. Align the screw holes and replace the remaining 5 screws and tighten by hand with a 5/16″ nut driver.
6.2 – Reattach Wiring Refer to Figures 4, 5 and 6 for location of sensors and harnesses and reattach the connectors to the AOC and MOC. While the order in which you reattach the wiring is not significant, you may find it easiest to start in the upper left hand of the AOC and move down and then right.
6.3 – Position the Liquid Line 1. Align the Liquid Line with the cutout on the drive.
2. Locate the rubber grommet that protects the Liquid Line from the sharp edges of the cabinet housing. Push the rubber grommet into the notch in the housing so that it is flush with the edge of the cabinet and the grommet is seated securely around the Liquid Line.
3. Position the Cold Plate over the Liquid Line and slide it over the bolts.
4. Place the 3 aluminum nuts on the bolts and hand tighten 2-3 turns.
5. Press the Liquid Line into the cutout so that it is properly aligned and seated into the cutout. Apply pressure to the Cold Plate and finger tighten the aluminum nuts. Repeat this process 3-4 times to ensure the Liquid Line is firmly seated in the cutout. You should see the Thermal Grease begin to flow around the copper tubing.
NOTICE: Use only the aluminum nuts that were on the unit originally or those that shipped with the Replacement Kit.
6.4 – Tighten the Aluminum Nuts Using a torque wrench, tighten the aluminum nuts to 40-50 in. lbs. of torque.
CAUTION. The aluminum nuts are designed to strip out at 80 in. lbs. DO NOT OVERTIGHTEN.
If you do not have a torque wrench, finger tighten the nuts as described above. With a felt tip marker, mark a position on the nut at 12 O’Clock and turn the nut to the 5 O’Clock position. See “Figure 9 Tighten Aluminum Nuts”.
1. Finger tighten nut, then mark the 12 O’Clock position.
2. Tighten to in. lbs of torque or to 5 O’Clock position.
DO NOT OVERTIGHTEN
Figure 9 – Tighten Aluminum Nuts
6.5 – Reattach Compressor Wiring 1. Plug in the Compressor plug to the connector at the
bottom of the Drive.
2. Reattach the shielded harness ground wire to the drive assembly.
Section 7. Perform Final Inspection
1. Verify that all wires and plugs are reconnected and that no wires are pinched between the Drive and the Cabinet Housing.
2. Start up Unit and verify operation.
3. Reattach the shielded harness ground wire to the drive assembly.
4. Verify that the Line Set Cover is in place.
Section 8. Return Drive Board
1. Package the failed control and return to your local parts center.
NOTE: To receive Factory Credit for failed Drive Boards covered by the Limited Warranty, a valid pre-authorization number is required. Be sure to mark the box and the service invoice with the preauthorization number before returning to your local parts center.
18-BC113D1-1C-EN
7
About Trane and American Standard Heating and Air Conditioning Trane and American Standard create comfortable, energy efficient indoor environments for residential applications. For more information, please visit www.trane.com or www.americanstandardair.com
The manufacturer has a policy of continuous data improvement and it reserves the right to change design and specifications without notice. We are committed to using environmentally conscious print practices.
18-BC113D1-1C-EN 13 Dec 2024 Supersedes 18-BC113D1-1B-EN (May 2024)
© 2024
Documents / Resources
 |
TRANE 18-BC113D1-1C-EN Integrated Variable or Multi Speed Control Drive Replacement [pdf] Installation Guide 18-BC113D1-1C-EN, 18-BC113D1-1C-EN, 18-BC113D1-1C-EN Integrated Variable or Multi Speed Control Drive Replacement, 18-BC113D1-1C-EN, Integrated Variable or Multi Speed Control Drive Replacement, Multi Speed Control Drive Replacement, Control Drive Replacement, Drive Replacement, Replacement |