CX310 3 Level Composite Workshop Trolley
“
Specifications
- Overall size: 1140 x 513 x 960mm
- Shelf size: 866 x 500mm
- Shelf capacity: 40kg/level
Product Description
The 3-Level Composite Workshop Trolley, Model No. CX310, is a
high-quality product manufactured by Sealey. It is designed for use
in workshops to assist in organizing and transporting tools and
equipment efficiently.
Product Usage Instructions
Safety Instructions
1. Ensure the trolley is chocked or secured before use.
2. Do not use the trolley on uneven ground or run over curbs or
steps.
3. Do not use the trolley if any part, especially the wheels, is
significantly damaged.
4. Keep children and unauthorized persons away from the work
area.
Assembly
- Assemble the trolley on a bench to protect against
scratches. - Fit four corner posts to the middle and bottom shelf.
- Attach two handles to the top shelf using the supplied
screws. - Attach all three shelves to the corner posts.
- Fix the four castors and tighten them with the provided
spanner. - Note: Shelves have one flush edge and three retaining edges.
The flush edge is the loading edge.
Environment Protection
Recycle unwanted materials instead of disposing of them as
waste. When the product is no longer serviceable, drain any fluids
into approved containers before disposal according to local
regulations.
FAQ
Q: What is the weight capacity of each shelf?
A: Each shelf has a capacity of 40kg.
Q: How should I secure the trolley before use?
A: Ensure the trolley is chocked or otherwise secured to prevent
movement.
Q: Can children use this trolley?
A: No, keep children and unauthorized persons away from the work
area for safety reasons.
“`
3-LEVEL COMPOSITE WORKSHOP TROLLEY MODEL NO. CX310
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and properly maintained, give you years of trouble free performance.
IMPORTANT: READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS. USE THIS TROLLEY CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
1. SAFETY INSTRUCTIONS
1.1. GENERAL SAFETY WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this trolley. 8 DO NOT overload the trolley – see 2. DESCRIPTION. 8 DO NOT drop loads on to shelves. 8 DO NOT place hot (above 100°C) items on to shelves. 9 Load shelves with the heaviest items on the lower shelves. 9 Use the trolley in a suitable work area. 9 Keep the work area clean, uncluttered and ensure there is adequate lighting. 9 Keep the trolley clean and tidy in accordance with good workshop practice. 8 DO NOT use the trolley for any purpose other than that for which it is designed. 8 DO NOT stand on the trolley, use it as a ladder or allow others to ride on the trolley. 9 Use the wheel locks to prevent the trolley from inadvertently moving. 8 DO NOT leave unattended, especially when loaded, unless the wheels are locked,
chocked or the trolley otherwise secured. 8 DO NOT use trolley on uneven ground and DO NOT run over curbs or steps, use a
ramp. 8 DO NOT use trolley if any part is significantly damaged, paying particular attention to the wheels. 9 Keep children and unauthorised persons away from the work area.
Flush edges
2. DESCRIPTION
Composite garage, workshop, or janitorial trolley with each shelf having a capacity of 40kg. Three shelves with shallow edge retaining walls on three sides and flush on one side for ease of adding or removing items. Two ergonomic and aesthetically styled operator handles. Four low friction Ø100mm swivel castors, two free and two locking.
3. SPECIFICATION
Overall size:……………………………….1140 x 513 x 960mm Shelf size:…………………………………………….866 x 500mm
Shelf capacity:……………………………………………40kg/level
4. CONTENTS
Carefully unpack the product and check the contents against the diagram and parts list below. Should any items be missing or damaged contact your Sealey dealer.
Description
Quantity
Description
Quantity
Description
Quantity
Description
Quantity
Spanner for castor
Shelf (top and middle)
Corner post
Castor
Screw for handle Washer for handle
Bottom shelf (for castors)
Handle
Castor (locking)
5.
5.1
5.1.1 5.1.2 5.1.3 5.1.4
ASSEMBLY
Assemble on a bench protecting against scratches, following sequence in fig1. Fit four corner posts to middle and bottom shelf. Fit two handles to top shelf with supplied screws. Fit all three shelves to corner posts. Fix 4 castors and tighten with provided spanner. Orientation Note! Shelves have one flush edge and three retaining edges. The flush edge is the loading edge.
(5.1.1) Rubber mallet
(5.1.3)
(5.1.2) (5.1.4)
Washer for castor
plain washer spring washer
© Jack Sealey Limited
fig1. Original Language Version
integral captive nut
CX310 Issue: 2 (F) 10/06/25
ENVIRONMENT PROTECTION Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids according to local regulations.
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice. Important: No Liability is accepted for incorrect use of this product. Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
© Jack Sealey Limited
Original Language Version
CX310 Issue: 2 (F) 10/06/25
Documents / Resources
 |
SEALEY CX310 3 Level Composite Workshop Trolley [pdf] Instruction Manual CX310 3 Level Composite Workshop Trolley, CX310, 3 Level Composite Workshop Trolley, Composite Workshop Trolley, Workshop Trolley, Trolley |