Saramonic WiTalk HUB Wi Talk System Full Duplex Wireless Intercom Headset System

Introduction

WiTalk series is a full-duplex wireless intercom headset system that offers two-way communication at a range of up to 400m. WiTalk system is ideal for applications where teams need full use of their hands, such as filmmaking, sports events, production crew communication, etc. It mainly includes the following product:

WiTalk HUB, a mini base station with two operating channels, can work with eight Remote headsets simultaneously. Its 3.5mm headphone & microphone combo jack can be connected to the WiTalk LBH (monaural intercom headset), creating a nine-person talk net.

Both WiTalk DMH (dual-ear master headset) and WiTalk SMH (single-ear master headset) can be used with four Remote headsets, allowing up to 5 people to communicate simultaneously. Both WiTalk DRH (dual-ear remote headset) and WiTalk SRH (single-ear remote headset) can be paired with any kind of master headset or base station.  WiTalk CB, a battery charger, can charge up to 10 batteries at the same time.

Product Structure

WiTalk DMH: Dual-Ear Master Headset

1. Microphone
2. Status Indicator
3. Power Button
   Press and hold to power on or off.
4. Volume Control ( +/- button)
   Press”+” or”-” button to increase or decrease the volume.
5. Mute Button
   • Mode Status Indicator
   • Mute Blinking red
   • Not mute Static blue
6. Release Button
7. Battery Compartment
8. USB-C Charging Port
9. Charging Indicator

WiTalk DRH: Dual-Ear Remote Headset

1. Microphone
2. Status Indicator
3. Power Button
   Press and hold to power on or off.
4. Volume Control(+/- button)
   Press”+” or”-” button to increase or decrease the volume.
5. Mute Button
   • Mode Status Indicator
   • Mute Blinking red
   • Not mute Static blue
6. Release Button
7.  Battery Compartment
8. USB-C Charging Port
9. Charging Indicator

WiTalk SMH: Single-Ear Master Headset

1. Microphone
2. Status Indicator
3. Power Button
   Press and hold to power on or off.
4. Volume Control ( +/- button)
   Press”+” or”-” button to increase or decrease the volume.
5. Mute Button
   • Mode Status Indicator
   • Mute Blinking red
   • Not mute Static blue
6. Release Button
7. Battery Compartment
8. USB-C Charging Port
9. Charging Indicator

WiTalk SRH: Single-Ear Remote Headset

1. Microphone
2. Status Indicator
3. Power Button
   Press and hold to power on or off.
4. Volume Control ( +/- button)
   Press”+” or”-” button to increase or decrease the volume.
5. Mute Button
   • Mode Status Indicator
   • Mute Blinking red
   • Not mute Static blue
6. Release Button
7. Battery Compartment
8. USB-C Charging Port
9. Charging Indicator

WiTalk HUB: Mini Base Station

1. Pairing Indicator
2. Pair Buttons of Channel A and Channel B
3. Volume Control Knob
4. Power Indicator
5. Power Button
   Press and hold to power on or off.
6. Belt Clip
7. Battery Compartment
8. Release Button
9. 3.Smm Headphone & Microphone Combo Jack
10. Link Jack
11. USB-C Charging Port
12. Charging Indicator

WiTalk LBH: Monaural Intercom Headset

1. Microphone
2. Audio Connector 3.5mm TRRS cable

WiTalk CB: 1 0-Bay Battery Charger

 

1. Battery Slots
2. Charging Indicators
3. DC Jack
4. 12V/2.5A DC Adapter
   (Including four types of detachable plug adapters: Europlug, American Standard, British Standard, Chinese Standard)

Operation Guide

How to Wear Witalk DMH/DRH/SMH/SRH/LBH

1. 1. Put on the headset and adjust it to a comfortable size and position.
2. Adjust the boom and position the microphone capsule at about 2cm in front of your mouth for optimum audio.

How to Use WiTalk LBH
Connect the headset to the jack ofWiTalk HUB

Headsets Pairing

Before leaving the factory, the WiTalk system is pre­paired. Therefore, the connection will be established once they are powered on. If they are disconnected, please follow the below steps:

1. Step 1: Make sure that the Master headset and Remote headset(s) are powered off.
2. Step 2: When the Master headset is in shutdown mode, press and hold its “+” button and power button simultaneously for about 3 seconds to enter pairing mode. The indicator will blink blue rapidly.
3. Step 3: When the Remote headset is in shutdown  mode, press and hold its “+” button and power button simultaneously for about 3 seconds to enter pairing mode. The indicator will blink blue rapidly. Do it for all Remote headsets in turn.
4. Step 4: When the Master headset and the Remote  headset(s) have entered the pairing mode, and the indicator of the Remote headset(s) turns to slowly blink blue, press the power button of the Master headset. They will be successfully paired within 10 seconds, and the indicators of both will turn to static blue.

Note:

1. Each Master headset can have a maximum of four Remote headsets paired.
2. When the number of the Remote headset is up to 4, the Master headset has reached the maximum pairing number by default. The pairing will be successful without the fourth step.
3. If the Master headset couldn’t enter the pairing mode, it will automatically turn on after its indicator blinks red rapidly for 5 seconds. This means that the Master headset has reached the maximum pairing number. If you want to re-enable the pairing mode, please clear the Master headset first.
4. The Master headset and Remote headset of the single-ear and dual-ear can be used for paired. The pairing method is the same as above.

Mode	Status Indicator
Unpaired	Blinking blue slowly
Paring	Blinking blue quickly
Paired Successfully	Static blue

Mini Base Station Pairing

1. Step 1: Make sure that the WiTalk HUB and the Remote headset are powered off.
2. Step 2: When the WiTalk HUB is in shutdown mode, press and hold its pair button (A or B) and power button simultaneously for about 3 seconds. The indicator will blink blue rapidly, and then the corresponding channel (A or B) enters the pairing mode.
3. Step 3: When the Remote headset is in shutdown mode, press and hold its “+” button and power button simultaneously for about 3 seconds to enter pairing mode. The indicator will blink blue rapidly. Do it for all Remote headsets in turn.
4. Step 4: When the WiTalk HUB and the Remote headset(s) have entered the pairing mode, and the indicator of the Remote headset(s) turns to slowly blink blue, press the power button of the WiTalk HUB. They will be successfully paired within 1 0 seconds, and the indicators of both will turn to static blue.

Note: Each channel can have a maximum of 4 Remote headsets paired. Thus, the WiTalk HUB can work with up to 8 Remote headsets simultaneously. After channel A is paired, if necessary, repeat the above steps to pair channel B.

Mode	Status Indicator
Unpaired	Blinking blue slowly
Paring	Blinking blue quickly
Paired Successfully	Static blue

Clearing the Master Headset
When pairing with a repaired or replaced unit, the Master headset needs to be cleared before a Remote headset can be paired. Follow the steps below to clear the Master headset:

1. Step 1: Make sure the Master headset is powered off.
2. Step 2: Press and hold the Master headset’s power button and “-” button simultaneously for 10 seconds until its indicator blinks red and blue alternately. When the indicator turns off, the Master headset is cleared.

Clearing the WiTalk HUB
When pairing with a repaired or replaced unit, the WiTalk HUB needs to be cleared before a Remote headset can be paired. Follow the steps below to clear the WiTalk HUB:

1. Step 1: Make sure the WiTalk HUB is powered off. Step 2: Press and hold the WiTalk HUB’s pair button A and power button simultaneously for 1 0 seconds. After channel A’s indicator blinks blue rapidly for 3 seconds, channel A is cleared and channel B still works normally.
2. Step 3: Press and hold the WiTalk HUB’s pair button B and power button simultaneously for 10 seconds. After channel B’s indicator blinks blue rapidly for 3 seconds, channel Bis cleared and then the WiTalk HUB will automatically shut down.

Battery Charging
Please recharge the device when battery is low.

Charge the battery via the charger.

1. Press the release button to remove the battery.
   • Mode Status Indicator
   • Low Battery  Static red
2. Insert the battery and make sure the contacts are properly aligned.
   • Mode  Charging Indicator (Charger)
   • Fully Charged
   • Charger Static red
   • Static blue
     
3. Charge the battery via a USB-C charging cable:
   • Mode Charging (Headset) Indicator  (Headset)
   • Charging Static red
   • Fully Charged Static blue

How to Mute Witalk DMH/DRH/SMH/SRH/LBH
Boom can swivel over the top 270 degrees. Thus, headset can be worn on both sides.

You can mute/ unmute the microphone in the following two ways:

1. Unmute: Set the boom to the “Vertical” position.
2. Press the MIC/MUTE button to mute or unmute the microphone.

Expanding the System
The system is expandable by adding more WiTalk HUB: Use a 3.5mm TRRS to TRRS adapter cable (sold separately) to connect one WiTalk HUB’s link jack to another WiTalk HU B’s headphone & microphone combo jack, doubling capacity to 16 full-duplex headsets.

Specifications

Dual-Ear Master Headset 

 

Dual-Ear Remote Headset (WiTalk DRH)

Single-Ear Master Headset (WiTalk SMH)

Single-Ear Remote Headset (WiTalk SRH)

Mini Base Station (WiTalk HUB)

Standards for Radio Frequency Band

For the latest frequency band and the more countries, please refer to our official website: www.saramonic.com

Packing List

WiTalkWT2D

• 1*WiTalk DMH Headset
• 1*WiTalk DRH Headset
• 2* WiTalk BP Battery
• 2* USB-C Charging Cable
• 1 * WiTalk Carrying Case (S)

WiTalkWT2S

• 1 * WiTalk SMH Headset
• 1 * WiTalk SRH Headset
• 2* WiTalk BP Battery
• 2* USB-C Charging Cable
• 1 * WiTalk Carrying Case (S)

WiTalkWT3D

• 1 * WiTalk DMH Headset
• 2* WiTalk DRH Headset
• 3* WiTalk BP Battery
• 3* USB-C Charging Cable
• 1 * WiTalk Carrying Case (S)

WiTalkWT3S

• 1 * WiTalk SMH Headset
• 2* WiTalk SRH Headset
• 3* WiTalk BP Battery
• 3* USB-C Charging Cable
• 1 * WiTalk Carrying Case (S)

WiTalkWT4D

• 1 * WiTalk DMH Headset
• 3* WiTalk DRH Headset
• 4* WiTalk BP Battery
• 4* USB-C Charging Cable
• 1 * WiTalk Carrying Case (S)

WiTalkWT4S

• 1 * WiTalk SMH Headset
• 3* WiTalk SRH Headset
• 4* WiTalk BP Battery
  4* USB-C Charging Cable
• 1 * WiTalk Carrying Case (S)

WiTalkWTSD

• 1 * WiTalk DMH Headset
• 4* WiTalk DRH Headset
• 5* WiTalk BP Battery
• 1 * WiTalk CB Battery Charger
• 1 * WiTalk Carrying Case (M)

WiTalkWTSS

• 1*WiTalkSMH Headset
• 4* WiTalk SRH Headset
• 5* WiTalk BP Battery
• 1 * WiTalk CB Battery Charger
• 1 * WiTalk Carrying Case (M)

WiTalkWT6D

• 1 * WiTalk HUB Base Station
• 5* WiTalk DRH Headset
• 6* WiTalk BP Battery
• 1 * WiTalk CB Battery Charger
• 1 * WiTalk LBH Headset
• 1 * WiTalk Carrying Case (M)

WiTalkWT6S

• 1 * WiTalk HUB Base Station
• 5* WiTalk SRH Headset
• 6* WiTalk BP Battery
• 1 * WiTalk CB Battery Charger
• 1 * WiTalk LBH Headset
• 1 *WiTalk Carrying Case (M)

WiTalkWT7D

• 1 * WiTalk HUB Base Station
• 6* WiTalk DRH Headset
• 7* WiTalk BP Battery
• 1 * WiTalk CB Battery Charger
• 1 * WiTalk LBH Headset
• 1 * WiTalk Carrying Case (L)

WiTalkWT7S

• 1 * WiTalk HUB Base Station
• 6* WiTalk SRH Headset
• 7* WiTalk BP Battery
• 1 * WiTalk CB Battery Charger
• 1 * WiTalk LBH Headset
• 1* WiTalk Carrying Case (L)

WiTalkWTSD

• 1 * WiTalk HUB Base Station
• 7* WiTalk DRH Headset
• 8* WiTalk BP Battery
• 1 * WiTalk CB Battery Charger
• 1 * WiTalk LBH Headset
• 1 * WiTalk Carrying Case (L)

WiTalkWTSS

• 1 * WiTalk HUB Base Station
• 7* WiTalk SRH Headset
• 8* WiTalk BP Battery
• 1 * WiTalk CB Battery Charger
• 1 * WiTalk LBH Headset
• 1 * WiTalk Carrying Case (L)

WiTalkWT9D

• 1 * WiTalk HUB Base Station
• 8* WiTalk DRH Headset
• 9* WiTalk BP Battery
• 1 * WiTalk CB Battery Charger
• 1 * WiTalk LBH Headset
• 1 * WiTalk Carrying Case (L)

WiTalkWT9S

• 1 * WiTalk HUB Base Station
• 8* WiTalk SRH Headset
• 9* WiTalk BP Battery
• 1 * WiTalk CB Battery Charger
• 1 * WiTalk LBH Headset
• 1 * WiTalk Carrying Case (L)

Statement

Please read this manual carefully before using the products and strictly operate & store it in accordance with the instructions. Please save the manual for your future reference. If you need further assistance than the user manual, please consult your retailer for help or email us : info@saramonic.com.

For better recording experience, the application SmartRecorder is recommended.

Scan the QR code and follow us!

A16 Building, Intelligent Terminal Industrial Park of Silicon Valley Power, Guanlan, Longhua District, Shenzhen, China

• 400-613-1096
• www.saramonic.com 
• info@saramonic.com

Frequently Asked Questions

• Q: How many headsets can work simultaneously with the WiTalk HUB?
  A: The WiTalk HUB can work with up to eight remote headsets simultaneously.
• Q: Can different types of headsets be paired together?
  A: Yes, both master and remote headsets from the WiTalk series can be paired with each other or the base station.
• Q: How far is the communication range of the WiTalk system?
  A: The WiTalk system offers a communication range of up to 400m.

Documents / Resources

Saramonic WiTalk HUB Wi Talk System Full Duplex Wireless Intercom Headset System [pdf] User Manual WiTalk HUB, WiTalk LBH, WiTalk DMH, WiTalk SMH, WiTalk DRH, WiTalk SRH, WiTalk CB, WiTalk HUB Wi Talk System Full Duplex Wireless Intercom Headset System, WiTalk HUB, Wi Talk System Full Duplex Wireless Intercom Headset System, Duplex Wireless Intercom Headset System, Wireless Intercom Headset System, Intercom Headset System, Headset System

References

• User Manual