MOSS LED 5 Channel X8 AMP DMX512 Decoder
Our most advanced standalone DMX Dimmer Ever. The Cinque-LED DMX Dimmer is fantastic. All the features our film, television, and theatrical friends have been asking for have been included. High current rating, smooth dimming, adjustable PWM frequency, 8-bit and 16-bit options, full manual mode, RDM control, XLR5 and RJ45 connections, Protect-A-FET technology, as well as UL certified as a component.
New Features in V3.2
- Brought back Terminal Block DMX I/O
- PWM Frequency adjustable via RDM
WARNING
DO NOT WIRE WITH POWER APPLIED TO DEVICE Only energize when all input and output power wires have been securely attached to terminal block. Connecting LEDs while Cinque is energized can expose LEDs to an overcurrent which will render them permanently damaged. CONSTANT CURRENT DEVICES ONLY Constant voltage LEDs will not operate properly and will likely be permanently damaged. DO NOT USE IN WET LOCATIONS Indoor use only. Do not expose device to excessive moisture.
DMX Address is 001, CH04
| DMX CHANNEL | FACTORY DEFAULT dp 1.1 | TRUE 16-BIT dp 2.1 | dp 5.4 | dp 6.4 |
| 1 | output 1 dim | output 1 dim | output 1 dim | output 1 dim |
| 2 | output 2 dim | output 1 fine dim | output 2 dim | output 2 dim |
| 3 | output 3 dim | output 2 dim | output 3 dim | output 3 dim |
| 4 | output 4,5 dim | output 2 fine dim | output 4,5 dim | output 4,5 dim |
| 5 | output 3 dim | master dim | master dim | |
| 6 | output 3 fine dim | strobe effects | ||
| 7 | output 4,5 dim | |||
| 8 | output 4,5 fine dim |
DMX Address is 001, CH05
| DMX CHANNEL | FACTORY DEFAULT dp 1.1 | TRUE 16-BIT dp 2.1 | dp 6.5 | dp 7.5 |
| 1 | output 1 dim | output 1 dim | output 1 dim | output 1 dim |
| 2 | output 2 dim | output 1 fine dim | output 2 dim | output 2 dim |
| 3 | output 3 dim | output 2 dim | output 3 dim | output 3 dim |
| 4 | output 4 dim | output 2 fine dim | output 4 dim | output 4 dim |
| 5 | output 5 dim | output 3 dim | output 5 dim | output 5 dim |
| 6 | output 3 fine dim | master dim | master dim | |
| 7 | output 4 dim | strobe FX | ||
| 8 | output 4 fine dim | |||
| 9 | output 5 dim | |||
| 10 | output 5 fine dim |
The data definitions for strobe channel are as follows:
- {0, 7}, //undefined
- {8, 65},//slow strobe ->fast strobe
- {66, 71},//undefined
- {72, 127},//slow push fast close
- {128, 133},//undefined
- {134, 189},//slow close fast push
- {190, 195},//undefined
- {196, 250},//random strobe
- {251, 255},//undefined
Restore to Factory Default Settings
Press and hold down both “Menu” & “Enter” keys until the digital display turns off, then release the keys. The system will reset and the digital display will turn on again. All settings will be restored to factory default.
The supported RDM PIDs are as follows:
- DISC_UNIQUE_BRANCH
- DISC_MUTE
- DISC_UN_MUTE
- DEVICE_INFO
- DMX_START_ADDRESS
- IDENTIFY_DEVICE
- SOFTWARE_VERSION_LABEL
- DMX_PERSONALITY
- DMX_PERSONALITY_DESCRIPTION SLOT_INFO
SLOT_DESCRIPTION MANUFACTURER_LABEL SUPPORTED_PPARAMETERS
WIRING DIAGRAM
WARNING
DO NOT WIRE WITH POWER APPLIED TO DEVICE Only energize when all input and output power wires have been securely attached to terminal block. Connecting LEDs while Cinque is energized can expose LEDs =to an overcurrent which will render them permanently damaged. CONSTANT CURRENT DEVICES ONLY Constant voltage LEDs will not operate properly and will likely be permanently damaged. DO NOT USE IN WET LOCATIONS Indoor use only. Do not expose device to excessive moisture.
OPERATION
DMX Mode (Decoder Mode) Using the “Up/DOWN” buttons you can cycle through the following menus.
- DMX address 1 to 507, default set to 001. The decimal after the “A” indicates reciving a DMX signal.
- DMX channel quantity, default set to CH05
- Bit resolution 8bit/16bit, default set to 16bit
- PWM frequency 500Hz to 35KHz, default set to 10KHz
- Dimming gamma curve value, default set to1.5
- Decoding mode, default set to dP1.1
- Switch between DMX Mode and Manual Mode
Protect-A-FET
When a short circuit occurs all the outputs will stop functioning and the LED display with flash. Power cycle it (turn it off then on again) to restore normal operation.
Manual Mode (Master Mode)
To enter Manual Mode use the “UP/DOWN” and set to “then with the “UP” button set to “ The following menu will apear. ”. Press “BACK” to confirm. Power cycle the unit.
- Program 1 to 31. P01 channel 1 is on P02 channel 2 is on etc…
- Manual control over channels 1 to 5 from 00 to FL
- Program brightness 1 to 8
- Program speed 1 to 16
- Switch between DMX Mode and Manual Mode
Set DMX Address
To set the DMX address select menu , press “ENTER” the display will flash. Press “UP/DOWN”to set the DMX address. Press “BACK” to confirm.
Set Channel Quantity
Select menu , press “ENTER” the display will flash. Press “UP/DOWN” and set the DMX channel quantity. Press “BACK” to confirm. Example: DMX address is set to 001.
- CH01 : DMX Footprint = 1 (DMX address for all channels is 001)
- CH02 : DMX Footprint = 2 (DMX address 001 for channels 1&3. DMX address 002 for channels 2, 4&5)
- CH03 : DMX Footprint = 3 (DMX address 001&002 for channels 1, 2. DMX address 003 for channels 3, 4&5)
- CH04 : DMX Footprint = 4 (DMX address 001&002&003 for channels 1, 2&3. DMX address 004 for channels 4&5)
- CH05 : DMX Footprint = 5 (DMX address 001,002,003,004&005 for channels 1, 2, 3, 4 ,5 respectively)
Resolution
press “ENTER” the display will flash. Press “UP/DOWN”to choose 8bit or 16bit. Press “BACK” to confirm.
PWM Frequency
Select menu , press “ENTER” the display will flash. Press “UP/DOWN” to choose from 00 to 35. Press “BACK” to confirm. Default
- @ 10khz.
- 01 = 1KHz
- 02 = 2KHz
- 03 = 3KHz
- 05 = 5KHz
- 06 = 6KHz
- 08 = 8KHz
- 09 = 9KHz
- 10 = 10KHz
- 12 = 12kHz
- 14 = 14KHz
- 18 = 18KHz
- 20 = 20KHz
- 35 = 35KHz
Select menu , press “ENTER” the display will flash. Pr ess “UP/DOWN” to choose 0.1 to 9.9. Press “BACK” to confirm.
Select menu , press “ENTER” the display will flash. Press “UP/DOWN” to choose the decoding mode. Press “BACK” to confirm.
DMX Address is 001, CH01
| DMX CHANNEL | FACTORY DEFAULT dp 1.1 | TRUE 16-BIT dp 2.1 |
| 1 | all output dim | all output dim |
| 2 | not in use | all output fine dim |
DMX Address is 001, CH02
| DMX CHANNEL | FACTORY DEFAULT dp 1.1 | TRUE 16-BIT dp 2.1 | dp 3.2 |
| 1 | output 1,3 dim | output 1,3 dim | output 1,3 dim |
| 2 | output 2,4,5 dim | output 1,3 fine dim | output 2,4,5 dim |
| 3 | output 2,4,5 dim | all output dim | |
| 4 | output 2,4,5 fine dim |
DMX Address is 001, CH03
| DMX CHANNEL | FACTORY DEFAULT dp 1.1 | TRUE 16-BIT dp 2.1 | dp 4.3 | dp 5.3 |
| 1 | output 1 dim | output 1 dim | output 1 dim | output 1 dim |
| 2 | output 2 dim | output 1 fine dim | output 2 dim | output 2 dim |
| 3 | output 3,4,5 dim | output 2 dim | output 3,4,5 dim | output 3,4,5 dim |
| 4 | output 2 fine dim | master dim | master dim | |
| 5 | output 3,4,5 dim | all output dim | strobe FX | |
| 6 | output 3,4,5 fine dim |
Documents / Resources
 | MOSS LED 5 Channel X8 AMP DMX512 Decoder [pdf] Instructions 5 Channel X8 AMP DMX512 Decoder |
