High CRI, Flexible LED Lighting, Flicker Free Dimming & DMX Control — Moss LED
Instructions for MOSS LED models including: 5 Channel X8 AMP DMX512 Decoder
DMX Address is 001, CH04. DMX CHANNEL. FACTORY DEFAULT. dp 1.1. TRUE 16-BIT. dp 2.1. dp 5.4. 1. output 1 dim output 1 dim. output 1 dim. 2 output 2 dim output 1 ne dim output 2 dim. 3. output...
www.mossled.com 1.800.924.1585 - 416.463.6677 info@mossled.com WWW.MOSS LED.COM MOSS Flexible LED Tape FlexLED The data definitions for strobe channel are as follows:
File Info : application/pdf, 2 Pages, 352.12KB
DocumentDocumentDMX Address is 001, CH04
DMX CHANNEL
FACTORY DEFAULT
dp 1.1
TRUE 16-BIT
dp 2.1
dp 5.4
dp 6.4
1
output 1 dim output 1 dim
output 1 dim
output 1 dim
2
output 2 dim output 1 fine dim output 2 dim
output 2 dim
3
output 3 dim output 2 dim
output 3 dim
output 3 dim
4
output 4,5 dim output 2 fine dim output 4,5 dim output 4,5 dim
5
output 3 dim
master dim
master dim
6
output 3 fine dim
strobe effects
7
output 4,5 dim
8
output 4,5 fine dim
DMX Address is 001, CH05
DMX CHANNEL
FACTORY DEFAULT
dp 1.1
TRUE 16-BIT
dp 2.1
dp 6.5
dp 7.5
1
output 1 dim output 1 dim
output 1 dim
output 1 dim
2
output 2 dim output 1 fine dim output 2 dim
output 2 dim
3
output 3 dim output 2 dim
output 3 dim
output 3 dim
4
output 4 dim output 2 fine dim output 4 dim
output 4 dim
5
output 5 dim output 3 dim
output 5 dim
output 5 dim
6
output 3 fine dim master dim
master dim
7
output 4 dim
strobe FX
8
output 4 fine dim
9
output 5 dim
output 5 fine dim 10
The data definitions for strobe channel are as follows:
{0, 7}, //undefined {8, 65},//slow strobe ->fast strobe {66, 71},//undefined {72, 127},//slow push fast close {128, 133},//undefined {134, 189},//slow close fast push {190, 195},//undefined {196, 250},//random strobe {251, 255},//undefined
The supported RDM PIDs are as follows:
DISC_UNIQUE_BRANCH DISC_MUTE DISC_UN_MUTE DEVICE_INFO DMX_START_ADDRESS IDENTIFY_DEVICE SOFTWARE_VERSION_LABEL DMX_PERSONALITY DMX_PERSONALITY_DESCRIPTION SLOT_INFO
SLOT_DESCRIPTION MANUFACTURER_LABEL SUPPORTED_PPARAMETERS
Restore to Factory Default Settings
Press and hold down both "Menu" & "Enter" keys until the digital display turns off, then release the keys. The system will reset and the digital display will turn on again. All settings will be restored to factory default.
Factory Default Settings
A.001 PF 10
CH 05 9A 1.5
B 16 DP 1.1
www.mossled.com 1.800.924.1585 - 416.463.6677
info@mossled.com
CONSTANT CURRENT
CINQUE-LED DMX DIMMER PROTECT-A-FET
5 CHANNEL X 8 AMP DMX512 DECODER
V 3.2
Our most advanced standalone DMX Dimmer Ever. The Cinque-LED DMX Dimmer is fantastic.
All the features our film, television, and theatrical friends have been asking for have been included. High current rating, smooth dimming, adjustable
PWM frequency, 8-bit and 16-bit options, full manual mode, RDM control, XLR5 and RJ45 connections, Protect-A-FET technology,
as well as UL certified as a component.
New Features in V3.2 1 - Brought back Terminal Block DMX I/O 2 - PWM Frequency adjustable via RDM
Input
5A MAX 12V to 48V DC
DMX
DMX512
512
5 Channel
IP Rating
IP 20
Output
12V to 48V DC 1A per Channel 60 ~ 240 Watts
Manual Mode
Temperature Range
-200C to +700C -40F to +1580F
PWM Frequency
500Hz to 35KHz
DMX 512 RDM Compliant
Dimensions
L 164mm 6-9/20" W 73mm 2-7/8" H 38mm 1-1/2"
Resolution
8 Bit & 16 Bit
E489028 Kg
UL Component Recognized
Weight
300g 10.5 oz
CONT DMX 5CH 12V48V LCD CC1000MA
38.00 mm
Type Input Number Input Display
Signal
of Channels
Voltage
Output
73.00 mm
! WARNING !
DO NOT WIRE WITH POWER APPLIED TO DEVICE Only energize when all input and output power wires have been securely
attached to terminal block. Connecting LEDs while Cinque is energized can expose LEDs
to an overcurrent which will render them permanently damaged.
CONSTANT CURRENT DEVICES ONLY Constant voltage LEDs will not operate properly
and will likely be permanently damaged.
DO NOT USE IN WET LOCATIONS Indoor use only.
Do not expose device to excessive moisture.
5 Pin XLR DMX In/Out
RJ45 DMX In/Out LED Output
OUTPUT MAX 5 X 1000MA
CONSTANT CURRENT CINQUE-LED DMX DIMMER
OUTPUT MAX 5 X 1000MA V3.2
GND
FOR USE WITH CONSTANT CURRENT PRODUCTS ONLY
SCAN QR CODE WITH YOUR PHONE
FOR MANUAL & MORE INFO
DMX OK
D-
E489028
D+
D-
D+
DMX IN/OUT MODEL # : CONTDMX5CH12V24VLCDCC1000
= DMX Decoder Mode = Manual Mode
HOLD BACK & ENTER FOR FACTORY RESET
XX = PWM Frequency(Default @ 10kHz)(00=500Hz ~ 35=35kHz) ( Set @ 10=10kHz for Flicker-Free on most camera settings )
XX = Resolution (Default @ 8 BIT)
XX = Set # of Channels (Default @ 5)
XX = Gamma Curve (Default @ 1.5) XX = Decoding Mode (Default @ 1.1)
INPUT 12 - 48VDC MAX POWER: 60 ~ 240 WATTS
Phoenix DMX in/Out
Digital Display DC Power In
164.00 mm
FlexLED Flexible LED Tape
MOSS
LED WWW.MOSS
.COM
WIRING DIAGRAM
! WARNING !
DO NOT WIRE WITH POWER APPLIED TO DEVICE Only energize when all input and output power wires have been securely
attached to terminal block. Connecting LEDs while Cinque is energized can expose LEDs
to an overcurrent which will render them permanently damaged.
CONSTANT CURRENT DEVICES ONLY Constant voltage LEDs will not operate properly
and will likely be permanently damaged.
DO NOT USE IN WET LOCATIONS Indoor use only.
Do not expose device to excessive moisture.
Master/Manual Mode
_ +
W B G R +
_ +
W B G R +
DMX Console
DMX Decoder Mode
_ +
W B G R +
OPERATION
DMX Mode (Decoder Mode)
Using the "Up/DOWN" buttons you can cycle through the following menus.
A.XXX
DMX address 1 to 507, default set to 001. The decimal after the "A" indicates reciving a DMX signal.
CH XX B XX PF XX 9A XX DP XX R N1
DMX channel quantity, default set to CH05 Bit resolution 8bit/16bit, default set to 16bit PWM frequency 500Hz to 35KHz, default set to 10KHz Dimming gamma curve value, default set to1.5 Decoding mode, default set to dP1.1 Switch between DMX Mode and Manual Mode
Protect-A-FET
When a short circuit occurs all the outputs will stop functioning and the LED display with flash. Power cycle it (turn it off then on again) to restore normal operation.
Manual Mode (Master Mode)
To enter Manual Mode use the "UP/DOWN" and set to "
" press "ENTER"
then with the "UP" button set to "
". Press "BACK" to confirm. Power cycle the unit.
The following menu will apear.
P.XXX
Program 1 to 31. P01 channel 1 is on P02 channel 2 is on etc...
1 5 XX to XX Manual control over channels 1 to 5 from 00 to FL
B XX
Program brightness 1 to 8
S XX
Program speed 1 to 16
R N2
Switch between DMX Mode and Manual Mode
1. Set DMX Address
To set the DMX address select menu
, press "ENTER" the display will flash.
Press "UP/DOWN"to set the DMX address. Press "BACK" to confirm.
2. Set Channel Quantity
Select menu
, press "ENTER" the display will flash. Press "UP/DOWN"
and set the DMX channel quantity. Press "BACK" to confirm.
Example: DMX address is set to 001. CH01 : DMX Footprint = 1 (DMX address for all channels is 001) CH02 : DMX Footprint = 2 (DMX address 001 for channels 1&3. DMX address 002 for channels 2, 4&5) CH03 : DMX Footprint = 3 (DMX address 001&002 for channels 1, 2. DMX address 003 for channels 3, 4&5) CH04 : DMX Footprint = 4 (DMX address 001&002&003 for channels 1, 2&3. DMX address 004 for channels 4&5) CH05 : DMX Footprint = 5 (DMX address 001,002,003,004&005 for channels 1, 2, 3, 4 ,5 respectively)
3. Resolution
Select menu
, press "ENTER" the display will flash. Press "UP/DOWN"
to choose 8bit or 16bit. Press "BACK" to confirm.
4. PWM Frequency
Select menu
, press "ENTER" the display will flash. Press "UP/DOWN"
to choose from 00 to 35. Press "BACK" to confirm. Default @ 10khz.
00 = 500Hz
03 = 3KHz
06 = 6KHz
09 = 9KHz
01 = 1KHz
04 = 4KHz
07 = 7KHz
10 = 10KHz
02 = 2KHz
05 = 5KHz
08 = 8KHz
12 = 12kHz
5. Gamma Curve Value
14 = 14KHz 16 = 16KHz 18 = 18KHz
20 = 20KHz 25 = 25KHz 35 = 35KHz
Select menu
, press "ENTER" the display will flash.
Press "UP/DOWN" to choose 0.1 to 9.9. Press "BACK" to confirm.
1.0
0.8
6.5
3.5
0.9 2.5
1.5
<1
>1
*Gamma adjusts the dimming curve of the unit so you can have an extremely high resolution low end or an extremely high resolution high end.
Output Brightness
DMX Value
6. Decoding Mode
Select menu
, press "ENTER" the display will flash.
Press "UP/DOWN" to choose the decoding mode. Press "BACK" to confirm.
DMX Address is 001, CH01
DMX CHANNEL
FACTORY DEFAULT
dp 1.1
TRUE 16-BIT
dp 2.1
DMX Address is 001, CH02
DMX
FACTORY DEFAULT
CHANNEL
dp 1.1
TRUE 16-BIT
dp 2.1
dp 3.2
1
all output dim all output dim
1
output 1,3 dim output 1,3 dim
output 1,3 dim
2
not in use all output fine dim
2
output 2,4,5 dim output 1,3 fine dim output 2,4,5 dim
3
output 2,4,5 dim
all output dim
DMX Address is 001, CH03
DMX
FACTORY DEFAULT
CHANNEL
dp 1.1
TRUE 16-BIT
dp 2.1
4
dp 4.3
1
output 1 dim
output 1 dim
output 1 dim
2
output 2 dim output 1 fine dim
output 2 dim
3
output 3,4,5 dim output 2 dim
output 3,4,5 dim
4
output 2 fine dim
master dim
5
output 3,4,5 dim
all output dim
6
output 3,4,5 fine dim
output 2,4,5 fine dim
dp 5.3
output 1 dim output 2 dim output 3,4,5 dim master dim
strobe FX