MEAN WELL LCM-60DA Series Multiple Stage Constant Current Mode LED Driver
Features
- Constant Current mode output with multiple levels selectable by dip switch
- Emergency lighting application is available according to IEC61347-2-13
- Built-in active PFC function and class Il design
- Standby power consumption <0.5W
- Functions: DALI interface(logarithm or linear dimming curve selectable), push dimming synchronization up to 10units
- 3 years warranty
Description
LCM-60DA series is a 60W AC/DC constant current mode output LED driver featuring the multiple levels selectable by dip switch and the DALI interface with the compliance to IEC62386. LCM-60DA operates from 180 ~ 295VAC and offers different current levels ranging between 500mA and 1400mA. Thanks to the high efficiency up to 92%, with the fanless design, the entire series is able to operate for -30°C ~+90°C case temperature under free air convection. In addition, LCM-60DA is equipped with push dimming and synchronization functions, so as to provide the optimal design flexibility for LED lighting system.
Applications
- LED indoor lighting
- LED office lighting
- LED commercial lighting
- LED panel lighting
- Industrial lighting
- GTIN CODE
- MW Search: https://www.meanwell.com/serviceGTIN.aspx
Model Encoding
TypeFunction Note
- Blank
- standby power consumption <0.5W In Stock
- AUX
- standby power consumption <1.2W and Auxiliary DC output(12V/50mA) By request
SPECIFICATION
| MODEL | LCM-60 – | ||||||
|
OUTPUT |
CURRENT LEVEL |
Current level selectable via DIP switch, please refer to”DIP SWITCH TABLE” section | |||||
| 500mA | 600mA | 700mA(default) | 900mA | 1050mA | 1400mA | ||
| RATED POWER | 60.3W | ||||||
| DC VOLTAGE RANGE | 2 ~ 90V | 2 ~ 90V | 2 ~ 86V | 2 ~ 67V | 2 ~ 57V | 2 ~ 42V | |
| OPEN CIRCUIT VOLTAGE (max.) | 95V | 73V | |||||
| CURRENT RIPPLE Note.5 | 5.0% max. @rated current | ||||||
| CURRENT TOLERANCE | ±5% | ||||||
| AUXILIARY DC OUTPUT | Nominal 12V(deviation 11.4~12.6V)@50mA for AUX-Type only | ||||||
| SETUP TIME Note.3
Note.9 |
500ms / 230VAC | ||||||
|
INPUT |
VOLTAGE RANGE Note.2 | 180 ~ 295VAC 254 ~ 392VDC
(Please refer to “STATIC CHARACTERISTIC” section) |
|||||
| FREQUENCY RANGE | 47 ~ 63Hz | ||||||
| POWER FACTOR (Typ.) | PF≧0.975/230VAC, PF≧0.95/277VAC@full load
(Please refer to “POWER FACTOR (PF) CHARACTERISTIC” section) |
||||||
| TOTAL HARMONIC DISTORTION | THD< 20%(@load≧75%)
(Please refer to “TOTAL HARMONIC DISTORTION(THD)” section) |
||||||
| EFFICIENCY (Typ.) Note.4 | 92% | ||||||
| AC CURRENT (Typ.) | 0.32A/230VAC 0.27A/277VAC | ||||||
| INRUSH CURRENT (Typ.) | COLD START 20A(twidth=270μs measured at 50% Ipeak) at 230VAC; Per NEMA 410 | ||||||
| MAX. No. of PSUs on 16A CIRCUIT BREAKER |
25 units (circuit breaker of type B) / 32 units (circuit breaker of type C) at 230VAC |
||||||
| LEAKAGE CURRENT | <0.5mA / 240VAC | ||||||
| STANDBY POWER CONSUMPTION Note.6 | <0.5W for Blank-Type, <1.2W for AUX-Type | ||||||
|
PROTECTION |
SHORT CIRCUIT | Constant current limiting, recovers automatically after fault condition is removed | |||||
| OVER VOLTAGE | 105 ~ 125V | ||||||
| Shutdown o/p voltage, re-power on to recover | |||||||
| OVER TEMPERATURE | Shutdown o/p voltage,re-power on to recover | ||||||
|
FUNCTION |
DIMMING | Please refer to “DIMMING OPERATION” section | |||||
| SYNCHRONIZATION | Please refer to “SYNCHRONIZATION OPERATION” section | ||||||
| TEMP. COMPENSATION | By external NTC, please refer to “TEMPERATURE COMPENSATION OPERATION”section | ||||||
|
ENVIRONMENT |
WORKING TEMP. | Tcase=-30 ~ +90℃ (Please refer to “ OUTPUT LOAD vs TEMPERATURE” section) | |||||
| MAX. CASE TEMP. | Tcase=+90℃ | ||||||
| WORKING HUMIDITY | 20 ~ 90% RH non-condensing | ||||||
| STORAGE TEMP., HUMIDITY | -40 ~ +80℃, 10 ~ 95% RH | ||||||
| TEMP. COEFFICIENT | ±0.03%/℃ (0 ~ 50℃) | ||||||
| VIBRATION | 10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes | ||||||
|
SAFETY & EMC |
SAFETY STANDARDS |
UL8750(except for DA2-Type), CSA C22.2 No.250.13-12, ENEC BS EN/EN61347-1, BS EN/EN61347-2-13, BS EN/EN62384
independent,GB19510.14, GB19510.1,BIS IS15885(except for DA2-Type), EAC TP TC 004 approved; According to BS EN/EN61347-2-13 appendix J suitable for emergency installations(EL)(AC Input: 200-240Vac)(for DA2-Type only) |
|||||
| DALI STANDARDS | IEC62386-101, 102, 207,251 | ||||||
| WITHSTAND VOLTAGE | I/P-O/P:3.75KVAC; I/P-DA:1.5KVAC; O/P-DA:1.5KVAC | ||||||
| ISOLATION RESISTANCE | I/P-O/P:>100M Ohms / 500VDC / 25℃/ 70% RH | ||||||
| EMC EMISSION Note.7 | Compliance to BS EN/EN55015, BS EN/EN61000-3-2 Class C(@load≧40%) ; BS EN/EN61000-3-3; GB/T 17743, GB17625.1, EAC TP TC 020 | ||||||
| EMC IMMUNITY | Compliance to BS EN/EN61000-4-2,3,4,5,6,8,11, BS EN/EN61547, light industry level(surge immunity Line-Line 2KV), EAC TP TC 020 | ||||||
|
OTHERS |
MTBF | 2270.7K hrs min. Telcordia SR-332 (Bellcore) ; 193.7K hrs min. MIL-HDBK-217F (25℃) | |||||
| DIMENSION | 123.5*81.5*23mm (L*W*H) | ||||||
| PACKING | 0.24Kg ; 54pcs/15Kg/1.12CUFT | ||||||
| NOTE | 1. All parameters NOT specially mentioned are measured at 230VAC input, rated current and 25℃ of ambient temperature.
2. De-rating may be needed under low input voltages. Please refer to “STATIC CHARACTERISTIC” sections for details. 3. Length of set up time is measured at first cold start. Turning ON/OFF the driver may lead to increase of the set up time. 4. Efficiency is measured at 900mA/67V output set by DIP switch. 5. Current ripple is measured 60%~100% of maximum voltage under rated power delivery. 6. Standby power consumption is measured at 180~230VAC. 7. The driver is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again. (as available on https://www.meanwell.com//Upload/PDF/EMI_statement_en.pdf) 8. The ambient temperature derating of 3.5℃/1000m with fanless models and of 5℃/1000m with fan models for operating altitude higher than 2000m(6500ft). 9. Based on IEC 62386-101/102 DALI power on timing and interruption regulations, the set up time needs to test with a DALI controller which can support for DALI power on function, otherwise the set up time will be higher than 0.5 second for DA2-type. 10. To fulfill requirements of the latest ErP regulation for lighting fixtures, this LED power supply can only be used behind a switch without permanently connected to the mains. ※ Product Liability Disclaimer：For detailed information, please refer to https://www.meanwell.com/serviceDisclaimer.aspx |
||||||
BLOCK DIAGRAM
DIP SWITCH TABLE
LCM-60DA/DA2 is a multiple-stage constant current driver, selection of output current through DIP switch is exhibited below.
| Io DIP S.W. | 1 | 2 | 3 | 4 | 5 | 6 |
| 500mA | —- | —- | —- | —- | —- | —- |
| 600mA | ON | —- | —- | —- | —- | —- |
| 700mA(factory default) | ON | ON | —- | —- | —- | —- |
| 900mA | ON | ON | ON | —- | —- | ON |
| 1050mA | ON | ON | ON | ON | —- | ON |
| 1400mA | ON | ON | ON | ON | ON | ON |
Note: For more current setting, please contact MW’s sales.
DIMMING OPERATION
PUSH dimming(primary side)
| Action | Action duration | Function |
| Short push | 0.1~1 sec. | Turn ON-OFF the driver |
| Long push | 1.5~10 sec. | Every Long Push changes the dimming direction, dimming up or down |
| Reset | >11 sec. | Set up the dimming level to 100% |
- The factory default dimming level is at 100%.
- If the push action lasts less than 0.05 sec., it will not lead to a change for the status of the driver.
- Up to 10 drivers can perform the PUSH dimming at the same time when utilizing one common push button.
- The maximum length of the cable from the push button to the last driver is 20 meters. LCM-60DA series
- The additive push button can be connected only between the PUSH terminal, as displayed in the diagram, and AC/L (in brown or black); it will lead to short circuit if it is connected to AC/N.
DALI interface(primary side; for DA/DA2-Type)
- Apply DALI signal between DA+ and DALCM-
- DALI protocol comprises 16 groups and 64 addresses.
- First step is fixed at 6% of output.
SYNCHRONIZATION OPERATION
- Synchronization up to 10 drivers (1 master + 9 slaves)
- Dimming operating range : 10%~100%
- Sync cable length : < 5m
- Sync cable type : Flat cable
- Sync cable cross section area : 22 – 24 AWG (0.2~0.3mm )
NOTE:
- Please make sure all units are set to 100% dimming setting (factory default) before synchronizing.
- Min. Dimming operating range depends on dimmer setting.
TEMPERATURE COMPENSATION OPERATION
LCM-60DA/DA2 have the built-in temperature compensation function; by connecting a temperature sensor (NTC resistor) between the +NTC / -NTC terminal of LCM-60DA/DA2 and the detecting point on the lighting system or the surrounding environment, output current of LCM-60DA/DA2 could be correspondingly changed, based on the sensed temperature, to ensure the long life of LED.
LCM-60DA/DA2 can still be operated normally when the NTC resistor is not connected and the value of output current will be the current level selected through the DIP switch.
- File Name: LCM-60DA-SPEC 2024-02-23
- NTC reference:
NTC resistance Output Current 220K < 60℃, 100% of the rated current (corresponds to the setting current level) > 60℃, output current begins to reduce, please refer to the curve for details.
330K < 70℃, 100% of the rated current (corresponds to the setting current level) > 70℃, output current begins to reduce, please refer to the curve for details.
470K < 80℃, 100% of the rated current (corresponds to the setting current level) > 80℃, output current begins to reduce, please refer to the curve for details.
Notes:
- MEAN WELL does not offer the NTC resistor and all the data above are measured by using THINKING TTC03 series.
- If other brands of NTC resistor is applied,please check the temperature curve first.
OUTPUT LOAD vs TEMPERATURE
STATIC CHARACTERISTIC
TOTAL HARMONIC DISTORTION (THD)
POWER FACTOR (PF) CHARACTERISTIC
EFFICIENCY vs LOAD
LCM-60DA series possess superior working efficiency that up to 91% can be reached in field applications.
- Tcase at 80℃
- Tcase at 80℃
MECHANICAL SPECIFICATION
Pin1(+FAN) / Pin2(-FAN) is the Auxiliary DC output for the optional model LCM-60DA-AUX; it can be used to drive fan.
Installation Manual
Please refer to http://www.meanwell.com/manual.html
Documents / Resources
 |
MEAN WELL LCM-60DA Series Multiple Stage Constant Current Mode LED Driver [pdf] Owner's Manual LCM-60DA Series Multiple Stage Constant Current Mode LED Driver, LCM-60DA Series, Multiple Stage Constant Current Mode LED Driver, Constant Current Mode LED Driver, Current Mode LED Driver, Mode LED Driver, LED Driver, Driver |
