LCDWIKI ESP32-32E 2.8inch Display Module User Manual

The product includes various resources such as sample programs,software libraries, hardware schematics, and more. Refer to the Product Information Pack catalog for detailed information.

Software Instructions:

To develop software for the display module:

Build the ESP32 platform software development environment.
Import third-party software libraries if needed.

Open or create a software project for debugging.
Power on the display module, compile, download the program, and check the effect.

If the effect is not as expected, modify the code and repeat the process.

Refer to the documentation in the 1-Demo directory for detailed steps.

Hardware Instructions:
The hardware instructions provide an overview of module resources, schematic diagrams, and precautions for use. Ensure to follow these guidelines for proper functioning of the display module.

Frequently Asked Questions

Q: Where can I find the software development environment setup instructions?
A: The setup instructions can be found in the 1-_Demo directory along with other relevant documents.

Q: What are the dimensions of the display module?
A: The product dimensions and 3D drawings can be found in the 3-_Structure_Diagram section of the product resources.

Rsource Description

The resource directory is shown in the following figure:

Directory	Content Description
1-Demo	The sample program code, the third-party software library that the sample program relies on, the third-party software library replacement file, the software development environment setup instruction document, and the sample program instruction document.
2 _Specification	Display module product specification, LCD screen specification and LCD display driver IC initialization code.
3-Structure_Diagram	Display module product dimensions and product 3D drawings
4- DataSheet	LCD display driver ILl9341 data book, resistance touch screen driver XPT2046 data book, ESP32 master data book and hardware design guidance document, USB to Serial IC(CH340C) data book, audio amplifier chip FM8002E data book, 5V to 3.3V regulator data book and battery charge management Chip TP4054 data sheet.
5-Schematic	Product hardware schematic, ESP32-WROOM-32E module 10 resource allocation table, schematic and PCB component package
6-User_Manual	Product user documentation
7I- Tool_software	WIFI and Bluetooth test APP and debugging tools, USB to serial port driver, ESP32 Flash download tool software, character take-up software, image take-up software, JPG image processing software and serial port debugging tools.
8-Quick_Start	Need to burn bin file, flash download tool and use instructions.

Software Instructions

Display module software development steps are as follows:

Build ESP32 platform software development environment;
if necessary, import third third-party software libraries as a basis for development;

open the software project to be debugged, you can also create a new software project;
power on the display module, compile and download the debugging program, and then check the software running effect;

the software effect does not reach the expected, continue to modify the program code, and then compile and download, until the effect r eaches the expected;

For details about the preceding steps, see the documentation in the 1 1-Demo directory.

Hardware Instructions

Overview of module hardware resources is displayed
Module hardware resources are shown in the following two figures:

The hardware resources are described as follows:

LCD
The LCD display size is 2.8 inches, the driver IC is ILI9341 , and the resolution is 24 0x 32 0. The ESP32 is connected using a 4-wire SPI communication interface.
- Introduction to ILI9341 controller
  The ILI9341 controller supports a maximum resolution of 240*320 and a172800-byte GRAM. It also supports 8-bit, 9-bit, 16-bit, and 18-bit parallel port data buses. It also supports 3-wire and 4-wire SPI serial ports. Since parallel control requires a large number of IO ports, the most common one is SPI serial port control. The ILI9341 also supports 65K, 262K RGB color display, display color is very rich, while supporting rotating display and scroll display and video playback, display in a variety of ways.
  The ILI9341 controller uses 16bit (RGB565) to control a pixel display, so it can display up to 65K colors per pixel. The pixel address setting is performed in the order of rows and columns, and the incrementing and decreasing direction is determined by the scanning mode. The ILI9341 display method is performed by setting the address and then setting the color value.
- Introduction to SPI communication protocol
  The writing mode timing of the 4 4-wire SPI bus is shown in the following figure:
  CSX is a slave chip selection, and the chip will only be enabled when CSX is at low power level.
  D/CX is the data/command control pin of the chip. When DCX is writing commands at low levels, data is written at high levels SCL is the SPI bus clock, with each rising edge transmitting 1 bit of data;
  SDA is the data transmitted by SPI, which transmits 8 bits of data at once. The data format is shown in the following figure:
  High bit first, transmit first.
  For SPI communication, data has a transmission timing, with a combination of real-time clock phase (CPHA) and clock polarity (CPOL):
  The level of CPOL determines the idle state level of the serial synchronous clock, with CPOL=0, indicating a low level. CPOL pair transmission protocol
  The discussion did not have much influence;
  The height of CPHA determines whether the serial synchronous clock collects data on the first or second clock jump edge,
  When CPHL=0, perform data collection at the first transition edge;
  The combination of these two forms four SPI communication methods, and SPI0 is commonly used in China, where CPHL=0 and CPOL=0
Resistive Touch Screen
The resistive touch screen is 2.8 inches in size and is connected to the XPT2046 control IC through four pins: XL, XR, YU, YD.
ESP32ESP32-WROOMWROOM-32E Module
This module has a built-in ESP32-DOWD-V3 chip, Xtensa dual-core 32-bit LX6 microprocessor, and supports clock rates up to 240MHz. It has 448KB ROM, 520KB SRAM, 16KB RTC SRAM, and 4MB QSPI Flash. 2.4GHz WIFI, Bluetooth V4.2 and Bluetooth Low power modules are supported. External 26 GPIOs, support SD card, UART, SPI, SDIO, I2C, LED PWM, motor PWM, I2S, IR, pulse counter, GPIO, capacitive touch sensor, ADC, DAC, TWAI and other peripherals.
MicroSD Card Slot
Using SPI communication mode and ESP32 connection, support for MicroSD cards of various capacities.
RGB Threehree-color Light
Red, green and blue LED lights can be used to indicate the running status of the program.
Serial Port
An external serial port module is used for serial port communication.
USB to Serial Port and One -click Download Circuit
The core device is CH340C, one end is connected to the computer USB, one end is connected to the ESP32 serial port, so as to achieve USB to TTL serial port.
In addition, a one one-click download circuit is also attached, that is, when downloading the program, it can automatically enter the download mode, without the need to touch through the external.
Battery Interface
TwoTwo-pin interface, one for the positive electrode, one for the negative electrode,access the battery power supply and charging.
Battery Charg e and Discharge Management Circuit
The core device is TP4054, this circuit can control the battery charging current,the battery is safely charged to saturation state, but also can safely control the battery discharge.
BOOT Key
After the display module is powered on, pressing will lower IO0. If the moment the module is powered on or the ESP32 is reset, lowering IO0 will enter the download mode. Other cases can be used as ordinary buttons.
TypeType-C Interface
The main power supply interface and program do wnload interface of the display module. Connect USB to serial port and one one-click download circuit, can be used for power supply, download and serial communication.
5V to 3.3V Voltage Regulator Circuit
The core device is the ME6217C33M5G LDO regulator. Th e voltage regulator circuit supports 2V~6.5V wide voltage input, 3.3V stable voltage output, and the maximum output current is 800mA, which can fully meet the voltage and current requirements of the display module.
RESET Key
After the display module is powered on, pressing will pull the ESP32 reset pin down (the default state is pull up), so as to achieve the reset function.

Resistive Touch Screen Control Circuit
The core device is XPT2046, which communicates with the ESP32 through SPI.
This circuit is the bridge between the resistive touch screen and the ESP32 master, responsible for transmitting the data on the touch screen to the ESP32 master, so as to obtain the coordinates of the touch point.
Expand the Pin
An input IO port, GND, and 3.3V pin th at are not used on the ESP32 module are led out for peripheral use.
Backlight control circuit
The core device is BSS138 field effect tube. One end of this circuit is connected to the backlight control pin on the ESP32 master, and the other end is connected to the negative pole of the LCD screen backlight LED lamp. Backlight control pin pull up, back light, otherwise off.

Speaker interface
Wiring terminals must be connected vertically. Used to access mono speakers and loudspeakers.
Audio power amp lifier circuit
The core device is the FM8002E audio amplifier IC. One end of this circuit is connected to the ESP32 audio DAC value output pin and the other end is connected to the horn interface. The function of this circuit is to drive a small power ho rn or speaker to sound. For 5V power supply, the maximum drive power is 1.5W (load 8 ohms) or 2W (load 4 ohms).
SPI peripheral interface
4-wire horizontal interface. Lead out an unused chip selection pin and SPI interface pin used by the MicroSD card, w hich can be used for external SPI devices or ordinary IO ports.

Detailed explanation of schematic diagram of display module

TypeType-C interface circuit
In this circuit, D1 is the Schottky diode, which is used to prevent the current from reversing. D2 to D4 are electrostatic surge protection diodes to prevent the display module from being damaged due to excessive voltage or short circuit. R1 is the pull pull-down resistance. USB1 is a Type Type-C bus . The display module connects to TypeType-C power supply, download programs, and serial port communication through the USB1. Where +5V and GND are positive power voltage and ground signals USB_D D- and USB_D+ are differential USB signals, which are transmitted t o the onboard USB USB-to -serial circuit.
5V to 3.3V voltage regulator circuit
In this circuit, C16~C19 is the bypass filter capacitor, which is used to maintain the stability of the input voltage and the output voltage. The U1 is a 5V to 3.3V LDO with the model number ME6217C33M5G. Because most of the circuits on the display module need 3.3V power supply, and the power input of the Type Type-C interface is basically 5V, so the voltage regulator conversion circuit is r equired.

Resistive touch screen control circuit
In this circuit, C25 and C27 are bypass filter capacitors, which are used to maintain th e input voltage stability. R22 is pullpull-up resistors used to maintain the default pin state as high. U4 is the XPT2046 control IC, the function of this IC is to obtain the coordinate voltage value of the touch point of the resistance touch screen through X+, X X-, Y+, Y Y- four pins, and then through ADC conversion, the ADC value is transmitted to the ESP32 master. The ESP32 master then converts the ADC value to the pixel coordinate value of the display. The PEN pin is a touch interrupt pin, and the input level is low when a touch event occurs.
USB to serial port and one one-click download circuit
In this circuit, U3 is a CH340C USB USB-to -serial IC, which does not need an external crystal oscillator to facilitate circuit design. C6 is a bypass filter capacitor used to maintain the input voltage stability. Q1 and Q2 are NPN type triodes, and R6 and R7 are triode base limiting current resistors. The function of this circuit is to realize USB to serial port and one one-click download function. The USB signal is input and output through UD+ and UD UD- pins, and is transmitted to the ESP32 master through RXD and TXD pins after conversion. One One-click download circuit principle:
- The RST and DTR pins of CH340C output high level by default. At this time,the Q1 and Q2 triode are not on, and the IO0 pins and reset pins of the ESP32 main control are pulled up to high level.
- The RST and DTR pins of CH340C output low levels, at this time, the Q1 and Q2 triode are still not on, and the IO0 pins and reset pins of the ESP32 main control are still pulled up to high levels.
- The RST pin of CH340C remains unchanged, and the DTR pin outputs a high level. At this time, Q1 is still cut off, Q2 is on, the IO0 pin of the ESP32 master is still pulled up, and the reset pin is pulled down, and the ESP32 enters the reset state.
- CH340C’s RST pin outputs a high level, DTR pin outputs a low level, at this time Q1 is on, Q2 is off, the reset pin of the ESP32 main control will not immediat ely become high because the connected capacitor is charged, ESP32 is still in the reset state, and IO0 pin is immediately pulled down, at this time it will enter the download mode.

Audio power amplifier circuit
In this circuit, R23, C7, C8 and C9 constitute the RC filter circuit, and R10 and R13 are the gain adjusting resistors of the operational amplifier. When the resistance value of R13 is unchanged, the smaller the resistance value of R10, the larger the vol ume of the external speaker. C10 and C11 are input coupling capacitors. R11 is the pull pull-up resistor. JP1 is the horn/speaker port. The U5 is the FM8002E audio power amplifier IC. After input by AUDIO_IN, the audio DAC signal is amplified by FM8002E gain an d output to the speaker/speaker by the VO1 and VO2 pins. SHUTDOWN is the enable pin for FM8002E. The low level is enabled. By default, the high level is enabled.
ESP32-WROOMWROOM-32E main control circuit
In this circuit, C4 and C5 are bypass filter capacitors, and U2 are ESP32ESP32-WROOMWROOM-32E modules. For details about the internal circuit of this module,please refer to the official documentation.
Key reset circuit
In this circuit, KEY1 is the key, R4 is the pull pull-up resistor, and C3 is the delay capacitor. Reset principle:
- After power power-on, C3 charges. At this time, C3 is equivalent to short circuit,RESET pin is grounded, ESP32 enters the reset state.
- When C3 is charged, C3 is equivalent to open circuit, RESET pin is pulled up,ESP32 reset is finished, and the ESP32 enters the normal working state.
- When KEY1 is pressed, the RESET pin is grounded, ESP32 enters the reset state, and C3 is discharged through KEY1.
- When KEY1 is released, C3 is charged. At this time, C3 is equivalent to short circuit, RESET pin is grounded, ESP32 is still in the RESET state. After C3 is charged, the reset pin is pulled up, ESP32 is reset and enters the normal working state.
  If the RESET is unsuccessful, the tolerance value of C3 can be appropriately increased to delay the reset pin low level time.
Interface circuit of serial module
In this circuit, P2 is a 4P 1.25mm pitch seat, R29 and R30 are impedance balance resistors, and Q5 is a field effect tube controlling the 5V input power supply.
R31 is a pull pull-down resistor. Connect RXD0 and TXD0 to serial pins, and supply power to the other two pins. This port is connected to the same serial port as the onboard USB USB-to -serial port module.
EXpand IO and peripheral interface circuit circuits
In this circuit, P3 a nd P4 are 4P 1.25mm pitch seats . SPI_CLK, SPI_MISO,SPI_MOSI pins are shared with MicroSD card SPI pins. Pins SPI_CS, IO35 are not used by on on-board devices, so they are led out to connect SPI, and can also be used for ordinary IO. Things to watch out for:
- IO35 can only be input pi ns;
Battery charge and discharge management circuit
In this circuit, C20, C21, C22 and C23 are bypass filter capacitors. U6 is the TP4054 battery charge management IC. R27 regulates the battery charging current. JP2 is a 2P 1.25mm pitch seat, connected to a battery. Q3 is a P P-channel FET. R28 is Q3 grid pull pull-down resistor. TP4054 charges the battery through the BAT pin, the smaller t he R27 resistance, the larger the charging current, the maximum is 500mA. Q3 and R28 together constitute the battery discharge circuit, when there is no power supply through the Type Type-C interface, the +5V voltage is 0, then the Q3 gate is pulled down to the low level, the drain and the source are on, and the battery supplies power to the entire display module. When powered through the Type Type-C interface, the +5V voltage is 5V, then the Q3 gate is 5V high, the drain and source are cut off, and the battery suppl y is interrupted.
18P LCD panel wire welding interface
In this circuit, C24 is the bypass filter capacitor, and QD1 is the 48P 0.8mmpitch liquid crystal screen welding interface. The QD1 has a resis tance touch screen signal pin, LCD screen voltage pin, SPI communication pin, control pin and backlight circuit pin. The ESP32 uses these pins to control the LCD and touch screen.

Download key circuit
In this circuit, KEY2 is the key and R5 is the pull pull-up resistor. IO0 is high bydefault and low when KEY2 is pressed. Press and hold KEY2, power on or reset, and the ESP32 will enter download mode. In other cases, KEY2 can be used as a normal key.
Battery power de tection circuit
In this circuit, R2 and R3 are partial voltage resistors, and C1 and C2 are bypass filter capacitors. The battery voltage BAT+ signal input passes through the divider resistor. BAT_ADC is the voltage value at both ends of R3, which is transmitted to the ESP32 master through the input pin, and then converted by ADC to finally obtain the battery voltage value. The voltage divider is used because the ESP32 ADC converts a maximum of 3.3V, while the battery saturation voltage is 4.2V, which is out of range. The obtained voltage multiplied by 2 is the actual battery voltage.
LCD backlight control circuit
In this circuit, R24 is the debugging resistance and is temporarily retained. Q4 is the N N-channel field effect tube, R25 is the Q4 grid pull pull-down resistor, and R26 is the backlight current limiting resistor. The LCD backlight LED lamp is in parallel state,the positive pole is connected to 3.3V, and the negative pole is connected to the drain of Q4. When the control pin LCD_BL outputs high voltage, the drain and source pole of Q4 are switched on. At this time, the negative pole of the LCD backlight is grounded, and the backlight LED lamp is switched on and emits light.
When the control pin LCD_BL outputs low voltage, the drain and source of Q4 are cut off, and the negative backlight of the LCD screen is suspended, and the backlight LED lamp is not switched on. By default, the LCD backlight is off.
Reducing the R26 resistance can increase the maximum brightness of the backlight.
In addition, the LCD_BL pin can input PWM signal to adjust the LCD backligh backlight.

RGB three three-color light control circuit
In this circuit, LED2 is an RGB three three-color lamp, and R14~R16 is a three three-color lamp current limiting resistor. LED2 contains red, green and blue LED lights, which ar e common anode connection, IO16, IO17 and IO22 are three control pins, which light up LED lights at low level and extinguish LED lights at high level.
MicroSD card slot interface circuit
In this circuit, SD_CARD1 is the MicroSD card slot. R17 to R21 are pull pull-up resistors for each pin. C26 is the bypass filter capacitor. This interface circuit adopts SPI communication mode. Supports high high-speed storage of MicroSD cards.
Note that this interf ace shares the SPI bus with the SPI peripheral interface.

Precautions for display module use

The display module is charged with the battery, the external speaker plays the audio, and the display screen is also working, at this time the total current may exceed 500mA. In this case, you need to pay attention to the maximum current supported by the Type Type-C cable and the maximum current supported by the power supply interface to avoid insufficient power supply.
During use, do not touch the LDO voltage regulato r and battery charge management IC with your hands to avoid being burned by high temperature.
When connecting the IO port, pay attention to the IO usage to avoid misconnecting and the program code definition does not match.

Use the product safely and reaso nably.

www.lcdwiki.com

Documents / Resources

LCDWIKI ESP32-32E 2.8inch Display Module [pdf] User Manual
ESP32-32E 2.8inch Display Module, ESP32-32E, 2.8inch Display Module, Display Module, Module

References

User Manual

LCDWIKI ESP32-32E 2.8inch Display Module

Product Information

Product Usage Instructions