B20-CTFB2 Bluetooth Smart Cabinet Lock
Specifications
- Quiescent current: 80uA
- Dynamic Current: 150mA
- Fingerprint capacity: 4
- Code capacity: 100pcs (temporary passwords), 50pcs (regular
passwords) - IC card capacity: 50pcs
- Fingerprint sensor type: [Not specified]
Product Usage Instructions
Initialization
1. Insert three AA-sized alkaline batteries into the battery
compartment on the rear panel.
2. Plug the connector of the rear panel into the socket of the
front panel.
3. Press the reset button until one long beep is heard to
initialize the lock. Note that this will erase all programmed
passcodes, access cards, and fingerprint templates.
Unlocking with Temporary Password
To unlock with a temporary password, follow the instructions
provided in the App after successful setup.
Networking of Devices
– This product is a Bluetooth smart cabinet lock.
– Download and install the Smart Life App or Tuya App for
binding with the lock.
Add Fingerprint
– Follow the steps in the manual to add a fingerprint to the
smart lock.
Add Bluetooth Lock
– Ensure the lock is in the initialization state before
proceeding with adding it to the App.
Add Code
– Set an 8-10-digit password through the App to unlock the smart
lock.
Add Card
– Use the lock’s keypad to add a card for unlocking.
Check Unlock Log
– When connected to Bluetooth, use the App to check the unlock
log for activity history.
Installation Steps
- Drill necessary holes in the door for installation.
- Insert batteries and ensure proper alignment of the front and
rear panels. - Install latch stopper ensuring proper door closure.
FAQ
Q: How do I reset the lock if needed?
A: Press and hold the reset button until you hear one long beep
to initialize the lock.
Q: Can I use both the Smart Life App and Tuya App with this
lock?
A: Yes, you can use either app for managing and controlling the
lock.
Operating Instruction
Initialization Insert three AA – sized alkaline batteries into the battery compartment on the rear panel. Subsequently, plug the connector of the rear panel into the socket of the front panel. Press the reset button until one long “beeps” are heard, at which point the lock is initialized. After initialization,all programmed passcodes, access cards, and fingerprint templates will be erased. (The lock is pre – initialized at the factory.)
Power
Unlock with temporary password
Rese button
Networking of devices >Tip: This product is a Bluetooth smart cabinet lock.The App administrator is the final administrator
of the lock.The owner of the Bluetooth smart cabinet lock must download the Smart Life App or Tuya App for binding.
1. Please download and install the Smart Life App or Tuya Smart from the Apple Store or mobile app market.
2. After the installation is complete, follow the prompts to register and log in. 3. Users can also scan the following QR code to download and install the application:
3.Unlock with temporary password APP can set temporary password, time-limited password, one-time password, and dynamicpassword. Once the setting is successful, enter the password to unlock..
Add fingerprint
Add bluetooth lock
>Add the lock to A pp (Must be in the initialization state)Please enter “8#” on the lock first, and then follow the steps below; (please operate within 1minute).
Add Code
4.Click “Add Fingerprint”and the green light of the smart lock starts flashing. Put the finger on the lock’s fingerprint sensor and read the same finger 8 times (different angles)
1.In the TuyaApp,click “+” and click “Add Device” 2.Wait for the device”Smart locker lock” to be found andclick on it to start pairing.
1
5.Click “Add code”and the green light of the smart lock starts flashing. 6.Enter an 8-10-digit password, click”Save”.
2
Add Card
Door frame
Out side
In side
7.Click “Add card” and the green light of the smart lock starts flashing. Put the card on thelock’s keypad.
Check unlock Log
8.check unlock Log When connected to Bluetooth, the App can check the unlock log.
Installation steps
46.50 Ø8 Ø16
Gap between the door “A”
Battery box 3pcs AA alkaline dry batteries
Lock body
M3.5*15 screw Latch stopper
Ø8
Front panel
28.00 64.00
M4 screw
.Drill a hole of 16mmdiameter and 2 holes of 8mm diameter in thedoor from the door edgeof 46.5mm.
.Put the plug through thedoor hole and insert intothe socket of the frontpanel. .Fix the front panel andthe rear panel on thedoor with 2 pcs M4 screws. .Load 3 pcs AA alkalinebatteries in the batteryholder
3
. Install the latch stopper: Draw a line at the center of the latch.
1. When installing the latch stopper, please reserve some space to install it, otherwise the cabinet door cannot be closed;
2.Tilt angle large side on the outside.
Door frame
Latch stopper
M3.5*15 screw
Keep the thickness of the door
.Install the latch stopper: Use 2pcs M3.5*16 screws to fix the latch stopper to the door.
Technical parameters
Technical parameter
No.
Items
Parameter
1
Quiescent current
80uA
2
Dynamic Current
150mA
3
Fingerprint capacity
4
Code capacity
100pcs 50pcs
5
IC card capacity
50pcs
6
Fingerprint sensor type
Semiconductor
7
Fingerprint recognition time
0.5s
8
Battery type
3pcs AA alkaline batteries /4.5V
9
Emergency charging port type
5V Type-c
10
Working Temperature
-20~55
11
Working humidity
20%~90%RH
4
Note
Don’t use carbon batteries
Documents / Resources
 |
globalsources B20-CTFB2 Bluetooth Smart Cabinet Lock [pdf] Instruction Manual B20-CTFB2, V2, B20-CTFB2 Bluetooth Smart Cabinet Lock, B20-CTFB2, Bluetooth Smart Cabinet Lock, Smart Cabinet Lock, Cabinet Lock |