Installation Guide
CTRL027
WWD2 -21W
Daintree® Networked
Wireless Wall Dimmer GE current WWD2 2IW Daintree Networked Wireless Wall DimmerGE current WWD2 2IW Daintree Networked Wireless Wall Dimmer - icon

GE current WWD2 2IW Daintree Networked Wireless Wall Dimmer - icon 1 BEFORE YOU BEGIN
Read these instructions completely and carefully.
Save these instructions for future use.

warning  WARNING / AVERTISSEMENT
RISK OF ELECTRIC SHOCK

  • Disconnect power before service installation, or maintenance of the product.
    RISK OF FIRE
  • Follow all relevant IEC or UL instructions and local building codes.
    RISK OF INJURY
  • Wears safety glasses and gloves during installation and servicing.

FCC / IC COMPLIANCE STATEMENTS
This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science, and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions:

  • This device may not cause interference.
  • This device must accept any interference, including interference that may cause undesired operation of the device.

To satisfy FCC/ISED RF exposure requirements a separation distance of 20 cm or more must be maintained between the antenna of this device and persons during operation. Operation at closer than 20cm is not permitted.

Prepare Electrical Wiring

Electrical Requirements

  • In the case of Digital bus miswiring, mains can be present on the device. Make sure all electricity is switched off before inspection.

GE current WWD2 2IW Daintree Networked Wireless Wall Dimmer - icon 2 Grounding Instructions

  • The grounding and bonding of the overall system shall be done in accordance with the National Electric Code (NEC) Article 600 and local codes.

IMPORTANT
To ensure the product warranty is valid, please ensure all installation instructions and environmental conditions for storage and operation are complied with. Installation to be performed by factory-trained or qualified personnel.
Save These Instructions
Use only in the manner intended by the manufacturer. If you have any questions, contact the manufacturer.

Installation

GE current WWD2 2IW Daintree Networked Wireless Wall Dimmer - fig GE current WWD2 2IW Daintree Networked Wireless Wall Dimmer - fig 1 GE current WWD2 2IW Daintree Networked Wireless Wall Dimmer - fig 2
Use a standard screwdriver  to remove the devices from the back housing Separate the battery cover from the device. Pull the plastic insulation strip out of the battery compartment.
Put the battery cover back on the device.
Insert the back housing piece into the junction box and secure with two screws.
GE current WWD2 2IW Daintree Networked Wireless Wall Dimmer - fig 3 GE current WWD2 2IW Daintree Networked Wireless Wall Dimmer - fig 4
Install the main body of the device into the back housing. Install the faceplate onto the device. Note: The device supports the use of other standard faceplates on the market.

Network Reset

GE current WWD2 2IW Daintree Networked Wireless Wall Dimmer - fig 5

To reset the network of the device, remove the faceplate from the device. Then press and hold the reset button for 5 seconds. Install the faceplate back onto the device.
Press either dimming up or down button to enter the pairing mode to join the device to a network.

Battery Replacement

GE current WWD2 2IW Daintree Networked Wireless Wall Dimmer - Battery Replacement GE current WWD2 2IW Daintree Networked Wireless Wall Dimmer - fig 6 GE current WWD2 2IW Daintree Networked Wireless Wall Dimmer - fig 7
The device’s LED flashing every 30 seconds indicates that the batteries need to be replaced. Remove the device from the back housing. Separate the battery cover from the device.  Replace the batteries with AAA batteries. All  batteries need to be replaced at the same time.
GE current WWD2 2IW Daintree Networked Wireless Wall Dimmer - fig 8 GE current WWD2 2IW Daintree Networked Wireless Wall Dimmer - fig 9
Install the main body of the device into the back housing. Install the faceplate onto the device. The device will rejoin its network automatically.

Product Dimensions

GE current WWD2 2IW Daintree Networked Wireless Wall Dimmer - fig 10

Product Overview

Technical Data

Product Specifications

Dimensions
Weight
Power Supply
battery life
Operating Environment
Status indicator
Mounting
Warranty
114mm H x 70mm W x 36mm D
130g
(4) AAA1.5V battery
5yr (normal operation)
-10°C to 40°C (Indoor Use Only)
The network joined/Button triggered
Surface-mounted, screw hole in the backplate, the cover could be removed
5 years

Product Availablity

SKU DESCRIPTION ARTICLE NO.
93141337 Daintree® Networked Wireless Wall Dimmer WWD2-2IW

Product Certifications

GE current WWD2 2IW Daintree Networked Wireless Wall Dimmer - icon 3

Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur  in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help

Supplier’s Declaration of Conformity
47 CFR § 2.1077 Compliance Information

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Model No: WWD2-2IW
Product Name:
Wireless Wall Dimmer
Suppliers Name: Current Lighting Solutions, LLC
Suppliers Address (USA): 1975 Noble Road, East Cleveland, OH 44112
Suppliers phone number and / or internet contact information: 1-866-855-8629

GE current
a Daintree company

www.gecurrent.com
© 2020 Current Lighting Solutions, LLC. All rights reserved. GE and the GE monogram are trademarks of the General Electric Company and are used under license. Information provided is subject to change without notice. All values are design or typical values when measured under laboratory conditions.
CTRL027 (Rev 07/05/20) Enovia – A-1025984

Documents / Resources

GE current WWD2-2IW Daintree Networked Wireless Wall Dimmer [pdf] Installation Guide
WWD2IW, 2AS3F-WWD2IW, 2AS3FWWD2IW, WWD2-2IW, Daintree Networked Wireless Wall Dimmer

References

Leave a comment

Your email address will not be published. Required fields are marked *