DrayTek V4.3.2.5 Vigor1000B Multi WAN Security Router User Guide

Q: What should I do if I encounter technical issues with the router?
- A: For technical issues, refer to the troubleshooting section in the user manual or contact DrayTek customer service for assistance.

PRODUCT INFORMATION

Intellectual Property Rights (IPR) Information

Copyrights © All rights reserved. This publication contains information that is protected by copyright. No part may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language without written permission from the copyright holders.

Trademarks The following trademarks are used in this document:

Microsoft is a registered trademark of Microsoft Corp.
Windows 8, 10, 11, and Explorer are trademarks of Microsoft Corp.

Apple and Mac OS are registered trademarks of Apple Inc.
Other products may be trademarks or registered trademarks of their respective manufacturers.

Safety Instructions and Approval

Safety Instructions

Read the installation guide thoroughly before you set up the router.

The router is a complicated electronic unit that may be repaired only by authorized and qualified personnel. Do not try to open or repair the router yourself.
Do not place the router in a damp or humid place, e.g. a bathroom.

Do not stack the routers.
The router should be used in a sheltered area, within a temperature range of +5 to +40 Celsius.

Do not expose the router to direct sunlight or other heat sources. The housing and electronic components may be damaged by direct sunlight or heat sources.
Do not deploy the cable for LAN connection outdoors to prevent electronic shock hazards.

Do not power off the device when saving configurations or firmware upgrades. It may damage the data in a flash. Please disconnect the Internet connection on the device before powering it off when a TR-069/ ACS server manages the device.
Keep the package out of reach of children.

When you want to dispose of the router, please follow local regulations on the conservation of the environment.

Warranty

We warrant to the original end-user (purchaser) that the router will be free from any defects in workmanship or materials for two (2) years from the date of purchase from the dealer. Please keep your purchase receipt in a safe place as it serves as proof of date of purchase. During the warranty period, and upon proof of purchase, should the product have indications of failure due to faulty workmanship and/or materials, we will, at our discretion, repair or replace the defective products or components, without charge for either parts or labor, to whatever extent we deem necessary tore-store the product to proper operating condition. Any replacement will consist of a new or re-manufactured functionally equivalent product of equal value ,and will be offered solely at our discretion. This warranty will not apply if the product is modified, misused, tampered with, damaged by an act of God, or subjected to abnormal working conditions. The warranty does not cover the bundled or licensed software of other vendors. Defects that do not significantly affect the usability of the product will not be covered by the warranty. We reserve the right to revise the manual and online documentation and to make changes from time to time in the contents hereof without obligation to notify any person of such revisions or changes.

EU Declaration of Conformity

Hereby, DrayTek Corporation declares that the equipment type Vigor1000B complies with EU EMC Directive 2014/30/EU, Low Voltage Directive 2014/35/EU, and RoHS 2011/65/EU.

Product name: Multi-WAN Security Appliance

Model number: Vigor1000B
Manufacturer: DrayTek Corp.
Address: No.26, Flushing Rd., Hukou, Hsinchu Industrial Park, Hsinchu 303, Taiwan

Package Content

Take a look at the package content. If anything is missing or damaged, please contact DrayTek or the dealer immediately.

Panel Explanation

LED

LED Status Explanation
PWR		On	The router is powered on.
PWR		Off	The router is powered off.
ACT		Blinking	The system is active.
ACT		Off	The system is hanged.
USB		On	The USB device is installed and ready.
USB		Off	No USB device is installed.
SFP+		On	The fiber connection is established.
		Blinking	The data is transmitted.
		Off	No fiber connection is established or the system is hanged.
P3 ~P10	Left	On	The Ethernet link is established on the corresponding port.
		Off	No Ethernet link is established.
		Blinking	The data is transmitted.
	Right	On	The Ethernet link is established on the corresponding port with 1G Mbps or above.
	Right	Off	The Ethernet link is established on the corresponding port with less than 1G Mbps.

Connectors

The ports “P3 to P6” are switchable. It can be used for LAN connection or WAN connection according to the settings configured in WUI.

Hardware Installation

This section will guide you to install the router through hardware connection and configure the router’s settings through web browser.

Connecting Device

Before starting to configure the router, you have to connect your devices correctly.

Connect a modem to any WAN port of Vigor1000B with Ethernet cable (RJ-45) to access Internet.
Connect the other end of the cable (RJ-45) to the Ethernet port on your computer (that device also can connect to other computers to form a small area network). The LAN LED for that port on the front panel will light up.
Connect a server/router (depends on your requirement) to any WAN port ofVigor1000B with Ethernet cable (RJ-45). The WAN LED will light up.
Connect the power cord toVigor1000B’s power port on the rear panel, and the other side into a wall outlet.
Power on the device by pressing down the power switch on the rear panel. The PWR LED should be ON.

The system starts to initiate. After completing the system test, the ACT LED will light up and start blinking. Below shows an outline of the hardware installation for your reference.

Rack-Mounted Installation

The Vigor1000B can be mounted on the shelf by using standard brackets shown below.

Fasten the rack mount kit on both sides of the Vigor router using specific screws.
Then, install the Vigor router (with rack mount kit) on the 19-inch chassis by using other four screws.

Software Configuration

To access Internet, please finish basic configuration after completing the hardware installation.

Quick Start Wizard for Network Connection

Make sure your PC connects to the router correctly.

Note You may either simply set up your computer to get IP dynamically from the router or set up the IP address of the computer to be the same subnet as the default IP address of Vigor router 192.168.1.1. For the detailed information, please refer to – Trouble Shooting of the user’s guide.

Open a web browser on your PC and type http://192.168.1.1. A pop-up window will open to ask for username and password. Please type “admin/admin” as the Username/Password and click Login.

Note If you fail to access to the web configuration, please go to “Trouble Shooting” on User’s Guide for detecting and solving your problem.

Now, the Main Screen will pop up. Click Wizards>>Quick Start Wizard.

If your router can be under an environment with high speed NAT, the configuration provide here can help you to deploy and use the router quickly. The first screen of Quick Start Wizard is entering login password. After typing the password, please click Next.

On the next page as shown below, please select the WAN interface that you use. Then click Next for next step.

You have to select the appropriate Internet access type (PPPoE, Static IP or DHCP) according to the information from your ISP. Here we take PPPoE and DHCP modes for WAN connection as examples.

For PPPoE Connection

Choose WAN3 as WAN Interface and click the Next button; you will get the following page.
Select PPPoE and click Next to get the following page.

Enter the Username/Password provided by your ISP. Then click Next for viewing the summary of such connection.
Click Finish. A page of Quick Start Wizard Setup OK!!! will appear. Then, the system status of this protocol will be shown.
- Quick Start Wizard Setup OK!

Now, you can enjoy surfing on the Internet.

For DHCP Connection

Choose WAN3 as WAN Interface and click the Next button; you will get the following page.

Select DHCP and click Next to get the following page.
Enter the hostname and / or MAC address provided by your ISP. Then click Next for viewing summary of such connection.
Click Finish. A page of Quick Start Wizard Setup OK!!! will appear. Then, the system status of this protocol will be shown.
- Quick Start Wizard Setup OK!
Now, you can enjoy surfing on the Internet.

Customer Service

If the router cannot work correctly after trying many efforts, please contact your dealer for further help right away. For any questions, please feel free to send e-mail to support@draytek.com.

Be a Registered Owner

Web registration is preferred. You can register your Vigor router via https://myvigor.draytek.com.

Firmware & Tools Updates

Due to the continuous evolution of DrayTek technology, all routers will be regularly upgraded. Please consult the DrayTek website for more information on the newest firmware, tools and documents.

https://www.draytek.com

GPL Notice

This DrayTek product uses software partially or completely licensed under the terms of the GNU GENERAL PUBLIC LICENSE. The author of the software does not provide any warranty. A Limited Warranty is offered on DrayTek products. This Limited Warranty does not cover any software applications or programs.

To download source codes please visit:

http://gplsource.draytek.com

GNU GENERAL PUBLIC LICENSE:

https://gnu.org/licenses/gpl-2.0
Version 2, June 1991

For any questions, please feel free to contact DrayTek technical support at support@draytek.com for further information.

Documents / Resources

DrayTek V4.3.2.5 Vigor1000B Multi WAN Security Router [pdf] User Guide
V4.3.2.5, V4.3.2.5 Vigor1000B Multi WAN Security Router, V4.3.2.5, Vigor1000B Multi WAN Security Router, Multi WAN Security Router, WAN Security Router, Security Router, Router

References

User Manual

DrayTek V4.3.2.5 Vigor1000B Multi-WAN Security Router3

Specifications

FAQs