datel PS5 xero Wireless Controller User Guide

To put the controller in Bluetooth pairing mode, hold down the SHARE button and press the button. This makes the controller visible in the PlayStation menu under Settings – Accessories – General – Bluetooth Accessories.

Charging Controller

Use the included USB cable to charge your Xero PS5 Controller.

The lights will briefly flash orange when charging. You can charge the controller from other USB power sources as well.

Wake-up & Sleep

If the controller is disconnected for more than 30 seconds, it will enter sleep mode. Pressing the button will wake it up and reconnect it to the PS5.
If there is no input for more than 10 minutes, the controller will go into sleep mode automatically.

Press the button to wake it up.

What’s in the box

1 x Wireless Xero controller

1 x USB-C Charging Cable

Connecting your Controller

NOTE – The console supports one primary controller per User, so to use your XERO Controller with an existing User you you must logout any controller already connected as that user.

If, when adding an additional controller, you assign it to a new User then the above steps are not required.
Connecting your Xero Wireless Controller to your PS5 console is very quick and easy.

The FIRST TIME you connect the Xero Controller to your console, you MUST do it via the USB-C cable, after which it will function wirelessly without the use of a cable.
1. Make sure the controller is fully charged (see Charging Controller section)
2. Turn on your console.
3. Connect your controller via the USB-C cable (supplied) to the console.
4. Then press the button on the controller until the light on the touch pad illuminates.
5. You can now disconnect the USB cable.
Once you have connected the Xero Controller via these steps you can just press the button in future to connect to the console via Bluetooth.

Bluetooth visibility

You can put the controller into Bluetooth pairing mode by holding down the “SHARE” button and pressing thebutton.
This enables you to make the controller visible when in the PlayStation menu “Settings” – “Accessories”-”General”-”Bluetooth Accessories”
The Xero Wireless controller will show up in your Bluetooth accessories as a “DualSense Wireless Controller”

Charging Controller

Use the included USB Cable to connect your Xero PS5 Controller to your PS5 console, you can do this with the console turned on or in standby mode.
When you connect the controller to the console via the USB cable the Lights will briefly flash ORANGE then go off while charging resumes.
To charge the controller while the console is in rest mode, you will have to enable this on the console.
The controller can also be charged from other USB power sources such as PC’s and Plug in chargers. Always use a USB cable that complies with the USB standard.
The light on controller may not always be visable when charging from other sources.

Controller

A: Direction Buttons
B: Share
C: Touchpad
D: Light Bar
E: Options
F: Action Buttons

H: Right Stick/R3 Button
I: Home Button/PS Button
J: Built-in Microphone

K: 3.5mm Headset Jack
L: Mute Button
M: Speaker

G: Left Stick/L3 Button
N: R1 Button
O: L1 Button

P: R2 Button
Q: L2 Button
R: USB C Port

S: FUNCTION R (FR)
T: FUNCTION L (FL)
U: Reset Button

Wake-up & Sleep

If the controller is disconnected from the console for more than 30 seconds it will enter sleep mode. By pressing the, it will wake up and automatically connect to the PS5.
When the controller is connected to the PS5 but receives no input from the user on any of the buttons, touchpad or joysticks for more than 10 minutes, the controller will automatically go into sleep mode.
To wake the controller up from sleep mode simply pressthe button and the Xero Controller will reconnect to the PS5.

Assigned Players

The Xero Wireless Controller will automatically indicate which player number is assigned to the controller via the coloured bar on the front edge of the touch pad.

Using Headphones

Plug the headphones into the controller’s 3.5 mm jack
Go to Settings

Select Sound
Select Audio Output
Select Output Device

Select Headset Connected To Controller
Set Output to Headphones to All Audio
Adjust the volume level

Resetting The Controller

If the Xero Wireless Controller becomes unresponsive or cannot connect to the console at any point, or the light on the front of the touchpad unexpectedly flashes, you need to reset the controller.
Please use a Paper Clip or similar to press and hold the RESET(U) button for 2 seconds on the underside of the controller, this will put the controller into original factory state.
You will need to re-connect the controller to the console.

Controller Modes

PLEASE NOTE: Your Xero Wireless Controller must be paired and connected to the PS5 console to be able to do any of the following tasks.
Also make sure the controller has not gone into sleep mode.

THE XERO CONTROLLER HAS TWO MODES TO OPERATE IN

Standard Controller Mode

In this mode the controller will operate similar to a regular PS5 controller. The cluster of lights will change depending on the game you are playing or which menu you are in on the interface.

Xero Remap Mode

In this mode the controller will always be ﬂashing a number of YELLOW lights. You are required to be in this mode to PLAY, MODIFY or DELETE a remapping Proﬁle.
TO SWITCH FROM EITHER MODE TO THE OTHER, HOLD (SHARE + OPTIONS) TOGETHER.

Button Remapping

The following steps will guide you through the remapping procedure.

The example illustrated is remapping the button to one of the rear paddles, in this case the FUNCTION R.
The buttons being pressed in this process are indicated in RED below.
1. If the controller isn’t already in remap mode (ﬂashing YELLOW). Activate it by pressing and holding the SHARE + OPTIONS buttons together until the lights ﬂash YELLOW.
2. OPTIONAL SLOT CHANGE
  - Proceed to 3 unless you want to change the SLOT being modiﬁed.
  - Quick press SHARE button to scroll through to desired slot 1, 2, 3, 4 or 5 (here SLOT2 is selected).
3. Press & hold the SHARE button while also holding the FUNCTION R paddle you wish to assign to, the lights will start to ﬂash quickly in BLUE, now release buttons.
4. Select the () button that you want to re-map to the selected FUNCTION R paddle.
  - The BLUE lights will brieﬂy go solid to signify the remap has worked, then return to ﬂashing YELLOW.
5. Now each time the FUNCTION R paddle is pressed it will produce (in our example) acommand.
  - The standardbutton on the controller will also function as normal.
6. If you wish to assign a second button to the other function paddle, simply repeat steps 3 & 4 selecting the desired paddle & button to change.
  - You can now either remap more buttons or leave in the current YELLOW ﬂashing state to continue gaming with the remap active.

Managing Proﬁles

Your Xero Wireless controller comes with 5 built-in Remap Proﬁles which you can customise to suit your gaming needs. Each proﬁle is depicted by the number of lights illuminated on the controller.

To switch between proﬁles, quickly press the SHARE button when in “Remap” mode and the lights will cycle through the 5 proﬁles continuously.
Stop on the one you want to modify, delete or keep active.
Each proﬁle can be conﬁgured individually with remapped buttons to suit a speciﬁc game. Within each proﬁle you can remap as many buttons as you wish.

All of the remapped buttons are saved to the controller, so when you exit remap mode or turn oﬀ your controller they will still be there when you turn it back on again.
When you turn back on the controller or return to remap mode the proﬁle you were last in will be loaded and will be indicated by the corresponding number of lights.

Remapping Options

The remapping function of the Xero Wireless Controller allows you to:

Switch buttons with each other.
Have several of the same button.
Have multiple buttons mapped to one.

Add buttons to the rear function paddles.

EXAMPLE:

If you wanted to change to the.

Make sure you are in Remap mode (YELLOW ﬂashing lights), change proﬁle (if you wish) using a quick press of the SHARE button.
Then hold SHARE +until the lights ﬂash BLUE, now release. Press, now the light will turn solid BLUE to signify it has been remapped then will return to the ﬂashing YELLOW of active slot.
Now pressing thebutton will have the effect of pressing the.

The buttonon the controller will still function as thetoo, so consider this when assigning buttons.
It is also easy to map multiple buttons to just the one on the controller.
For example you could have L1+L2 mapped to the single Function R paddle on the rear of the controller

To do this simply press L1+L2 at the same time when assigning your buttons to Function R.
The following digital buttons can be used for remapping: L1, L2, L3, R1, R2, R3,
To reset an individual button within a proﬁle, hold SHARE and the speciﬁc button until the lights ﬂash BLUE, then simply press the SHARE button again, that button will now be the default PS5 button again.

To erase the mapping for a whole proﬁle, toggle to the desired one by tapping the SHARE button, then hold the SHARE button for about 3 seconds until all lights turn RED. That Proﬁle is now erased and returned to default PS5 button setup.
Remember the controller will only work with your modiﬁed buttons if the controller is still in remap mode” with the YELLOW proﬁle lights illuminated on the controller.

Maintenance & Safety

Do not use in places with high humidity, high temperatures, dust, strong magnetics or corrosive gas.

Do not disassemble or modify the controller.
Do not insert foreign objects into any part of the controller and it’s ports.
Do not use solvents or chemicals to clean the controller.

Use only a dry, soft cloth to clean the controller.
Keep away from water.
Do not place the controller on unstable surfaces.

Do not put items on top of the controller.
Do not place the controller in places which could harm other.
Do not throw or drop the controller or subject it to violent forces.

When removing the USB cable, do so gently to avoid damaging the console or controller.

Precautions

Keep out of reach from young children.

Avoid extended periods of use.
Limit volume if using headphones to protect your hearing.
Be aware of your surrounding when playing.

Stop playing if you feel tired or ill.
Do not handle exposed or damaged lithium-ion battery.

Storage

Do not store or transport where high temperatures and humity are present.

Do not expose to dust, smoke or steam.
Keep out of direct sunlight.

Customer Services

THIS PRODUCT IS NOT SPONSORED, ENDORSED, OR APPROVED BY SONY INTERACTIVE ENTERTAINMENT INC

Technical Support

Before contacting Datel’s customer service department, please ensure that you have read through and understood the information in this manual/guide.
If you contact support, please ensure that you have information on when and where you purchased this product to hand.

Datel Customer Services
Customers Services,
Datel Electronics Ltd,

Stafford Road,
Stone,
Staffordshire,

ST15 0DG.
UNITED KINGDOM
Web: https://support.codejunkies.com
© 2025 Datel Ltd. Xero is a trademark of Datel Ltd. Playstation is a trademark or registered Trademark of the SONY COMPANY. All other trademarks are the property of their respective owners.
Xero Wireless Controller is a 100% unofficial product and is NOT sponsored, endorsed or approved by SONY, nor any games developer or publisher.

FAQ

How do I know which player number is assigned to the controller?
- The Xero Wireless Controller indicates the player number via the colored bar on the front edge of the touch pad.

Documents / Resources

datel PS5 xero Wireless Controller [pdf] User Guide
PS5, PS5 xero Wireless Controller, xero Wireless Controller, Wireless Controller, Controller

References

User Manual

datel PS5 xero Wireless Controller

Product Usage Instructions