DATALOGIC MEMOR 3X Rugged Mobile Computer User Guide

Top View: Power Key, Data Capture Window
Front View: Charging LED, Touch Panel
Display
Back: Home, Recent
Back View: Camera, LED Flash, Battery Swap LED,
SIM Card Socket, MicroSD Card Socket
Side View: Volume Control Buttons, Left Trigger,
Right Trigger
Bottom View: USB Type-C Port

Battery Installation

Insert the battery pack into the slot, bottom first, and press
it firmly into place.

Rubber Boot Installation

To add the optional rubber boot for extra protection, insert the
device top first. To remove it, grip the sides and press the back
bottom of the device with thumbs.

Charging Instructions

The battery requires charging upon initial use. Connect it to a
power source using a USB Type-C cable or compatible dock. The
charging LED will turn red during charging and green once fully
charged.

FAQ

Q: How do I check the battery level on the Memor 3X?

A: You can check the battery level on the device’s display or
settings menu.

Q: Can I use third-party accessories with the Memor 3X?

A: It is recommended to use Datalogic-approved accessories to
ensure compatibility and optimal performance.

“`

View Fullscreen

Datalogic S.r.l.
Via San Vitalino 13 40012 Calderara di Reno (BO) Italy Tel. +39 051 3147011 Fax +39 051 3147205
©2024 Datalogic S.p.A. and/or its affiliates All rights reserved. Without limiting the rights under copyright, no part of this documentation may be reproduced, stored in or introduced into a retrieval system, or transmitted in any form or by any means, or for any purpose, without the express written permission of Datalogic S.p.A. and/or its affiliates. Owners of Datalogic products are hereby granted a non-exclusive, revocable license to reproduce and transmit this documentation for the purchaser’s own internal business purposes. Purchaser shall not remove or alter any proprietary notices, including copyright notices, contained in this documentation and shall ensure that all notices appear on any reproductions of the documentation. Electronic versions of this document may be downloaded from the Datalogic website (www.datalogic.com). If you visit our website and would like to make comments or suggestions about this or other Datalogic publications, please let us know via the “Contact” page.
Disclaimer
Datalogic has taken reasonable measures to provide information in this manual that is complete and accurate, however, Datalogic shall not be liable for technical or editorial errors or omissions contained herein, nor for incidental or consequential damages resulting from the use of this material. Datalogic reserves the right to change any specification at any time without prior notice.
Trademarks
Datalogic and the Datalogic logo are registered trademarks of Datalogic S.p.A. in many countries, including the U.S.A. and the E.U. Memor is a trademark of Datalogic S.p.A. and/or its affiliates. All other brand and product names may be trademarks of their respective owners.
REFERENCE DOCUMENTATION
For further information regarding Memor 3X refer to the SDK help on-line and to the Memor 3X User’s Manual, downloadable from our website: https://developer.datalogic.com/mobile-computers.
Support Through the Website
Datalogic provides several services as well as technical support through its website. Log on to www.datalogic.com. For quick access, from the home page click on the search icon , and type in the name of the product you’re looking for. This allows you access to download Data Sheets, Manuals, Software & Utilities, and Drawings. Hover over the Support & Service menu for access to Services and Technical Support.

MEMORTM 3X
QUICK START GUIDE
Rugged Mobile Computer/ Barcode Reader with 1D/2D Imager Model: SGVNR/SGVNRNA (WAN SKU)
Model: SGVWF (WLAN SKU)
©2024 Datalogic S.p.A. and/or its affiliates · All rights reserved · Without limiting the rights under copyright, no part of this documentation may be reproduced, stored in or introduced into a retrieval system, or transmitted in any form or by any means, or for any purpose, without the express written permission of Datalogic S.p.A. and/or its affiliates · Datalogic and the Datalogic logo are registered trademarks of Datalogic S.p.A. in many countries, including the U.S. and the E.U.
www.datalogic.com
822004610 (Rev. A) February 2024

OUT OF THE BOX
The Memor 3X package contains: y Memor 3X PDA
(Model SGVNR/SGVNRNA – WAN SKU; Model SGVWF – WLAN SKU) y Rechargeable one-piece battery pack y Quick Start Guide y Safety & Regulatory Addendum y End User License Agreement (EULA) Sheet Remove all the components from their packaging; check their integrity and compare them with all the packing documents.
CAUTION: Keep the original packaging for use when sending products to the technical assistance center. Damage caused by improper packaging is not covered under the warranty.
GENERAL VIEW
Top View
Power Key
Data Capture Window
Front View
Charging LED

Touch Panel Display

Back

Home

Recent

Back View

Camera
LED Flash
Battery Swap LED

SIM Card Socket

MicroSD Card Socket
Side View

Volume Control Buttons
Left Trigger

Right Trigger

Bottom View
USB Type-C Port

BATTERY INSTALLATION
Insert the battery pack into the slot, bottom first, and press it into place:
RUBBER BOOT INSTALLATION
The rubber boot provides additional protection to the device and is available as optional accessory (P/N 944CC0374). Insert the device into the rubber boot, top first.
To remove the rubber boot, grab the rubber boot sides with your fingers while pressing the back bottom of the device with your thumbs, as shown in the picture below.
CHARGING INSTRUCTIONS
The battery pack is not initially fully charged. After installing the battery, charge it with a USB Type-C cable or with a dock (single slot dock, 4-slot dock, vehicle dock, 4-slot battery charger). During the charging process the charging LED positioned at the top right side of the display glows red constantly. Once the charging process has been completed, the charging LED glows green constantly.

Charge with USB
Use a USB Type-C cable in conjunction with the power supply adapter (sold separately, p/n 94ACC0383) to charge the device from a power outlet. The charger is modular, with one adapter and five switchover plugs.
You can also use the USB cable to charge the Memor 3X from any self-powered USB hub or USB port on a computer.
CAUTION: Use only the Datalogic power supply 94ACC0383 to power the Memor 3X.
Charge with the Dock
Install the rubber boot on the device, or insert the adapter into the dock as shown below.
Insert the device into the dock with the screen facing front and the head facing up.
Memor 3X with Rubber Boot Memor 3X without Rubber Boot
To remove the device from the dock, pull it upwards while holding the dock firmly down.

CAUTION: Use only the Datalogic power supply 94ACC0383 to power any of the docks. Do not put any foreign object such as, but not limited to, coins, paper clips, stickers inside the slot of any of the docks. Do not apply any sticker to the Memor 3X (see the examples below). NOTE: For information on the single slot dock/ 4-slot dock/ vehicle dock/ 4-slot battery charger refer to the Quick Start Guide included in the dock’s box. NOTE: The Memor 3X may get warm during charging. This is normal and does not mean a malfunction.
INSTALL THE SIM/SD CARD
Access the SIM/SD card slots 1. Turn off the Memor 3X or put it in swap bat-
tery mode (refer to the User’s Manual for more details). 2. Press the battery latches and remove the battery pack.
3. Remove the SIM/SD rubber cover
Install the SIM Card1 1. Slide the cardholder to the left and then pull it up.
2. Insert the SIM card with the written part upward. Push the cardholder down and then slide it to the right.
1 Phone feature is available only on SGVNR/SGVNRNA models

Install the Sd Card 1. Slide the cardholder to the left and then pull it up.
2. Insert the SIM card cardholderas shown below. Push the cardholder down and then slide it to the right.
Replace the SIM/SD rubber cover and press it, then replace the battery (see “Battery Installation”).
SCANNING AND IMAGING
To scan a barcode symbol: 1. Point the scan window at the barcode from a
distance within the reading range. 2. Press one of the scan triggers. The imager
projects a laser aiming pattern similar to those used on cameras. The aiming pattern is used to position the barcode or object within the field of view.
3. Center the symbol in any orientation within the aiming pattern. Ensure the entire symbol is within the rectangular area formed by the brackets in the aiming pattern, then either wait for the timeout or release the Scan Key to capture the image. A red beam illuminates the symbol, which is captured and decoded.
Linear Bar Code 2D Matrix Symbol
Relative Size and Location of Aiming System Pattern If the scan has been successful: y If enabled, the good read beep plays. y If enabled, the GreenSpot projects a green spot
onto the bar code image. y If enabled, the good read indicator positioned at
the top left side of the display glows solid green.

Documents / Resources

DATALOGIC MEMOR 3X Rugged Mobile Computer [pdf] User Guide
U4G-SGVWF, U4GSGVWF, sgvwf, MEMOR 3X Rugged Mobile Computer, MEMOR 3X, Rugged Mobile Computer, Mobile Computer, Computer

References

User Manual

DATALOGIC MEMOR 3X Rugged Mobile Computer User Guide

MEMOR 3X Rugged Mobile Computer

Specifications

Product Usage Instructions

Out of the Box

General View