Datalogic Memor 3X Quick Start Guide

Rugged Mobile Computer / Barcode Reader

Models: SGVNR/SGVNRNA (WAN SKU), SGVWF (WLAN SKU)

Introduction

This document provides essential information for quickly setting up and using your Datalogic Memor 3X device. It covers unboxing, device overview, battery installation, charging, SIM/SD card insertion, and basic scanning operations.

For detailed information, refer to the Memor 3X User's Manual available at developer.datalogic.com/mobile-computers.

About Datalogic

Datalogic S.r.l. is a global technology leader in automatic data capture and industrial automation solutions. For support and more information, visit www.datalogic.com.

Out of the Box

The Memor 3X package typically contains:

Memor 3X PDA (Model SGVNR/SGVNRNA - WAN SKU; Model SGVWF - WLAN SKU)
Rechargeable one-piece battery pack
Quick Start Guide
Safety & Regulatory Addendum
End User License Agreement (EULA) Sheet

Please check all components for integrity against the packing documents.

CAUTION: Keep the original packaging for use when sending products to the technical assistance center. Damage caused by improper packaging is not covered under warranty.

General View of the Memor 3X

Familiarize yourself with the device's components:

Top View

The top view shows the Power Key and the Data Capture Window.

Front View

The front view displays the Touch Panel Display, Home button, Recent button, and the Charging LED indicator.

Back View

The back view features the Camera, LED Flash, Battery Swap LED, and the SIM Card Socket.

Side View

The side view highlights the Volume Control Buttons, Left Trigger, and Right Trigger.

Bottom View

The bottom view shows the USB Type-C Port.

Battery Installation

To install the battery, insert it into the slot at the bottom first and press it into place.

Rubber Boot Installation

The optional rubber boot provides additional protection. To install, insert the device into the boot from the top. To remove, grip the boot sides with your fingers while pressing the back bottom of the device with your thumbs.

Charging Instructions

The battery pack is not fully charged initially. Charge it using a USB Type-C cable connected to a power adapter or a computer's USB port, or by placing the device in a charging dock (single slot, 4-slot, vehicle, or 4-slot battery charger).

During charging, the charging LED indicator, located at the top right of the display, glows red. Once charging is complete, the LED turns solid green.

CAUTION: Use only the Datalogic power supply (p/n 94ACC0383) for the Memor 3X and its docks. Do not insert foreign objects like coins, paper clips, or stickers into the dock slots. Do not apply stickers to the Memor 3X.

NOTE: The Memor 3X may become warm during charging, which is normal.

Installing SIM and SD Cards

To access the SIM/SD card slots:

Turn off the Memor 3X or put it in swap battery mode (refer to the User's Manual for details).
Press the battery latches and remove the battery pack.
Remove the SIM/SD rubber cover.

Installing the SIM Card

Slide the cardholder to the left and pull it up.
Insert the SIM card with the written part upward. Push the cardholder down and then slide it to the right. (SIM card functionality is available only on SGVNR/SGVNRNA models).

Installing the SD Card

Slide the cardholder to the left and pull it up.
Insert the SD card into the cardholder as shown. Push the cardholder down and then slide it to the right.

After installation, replace the SIM/SD rubber cover and press it firmly, then re-install the battery.

Scanning and Imaging

To scan a barcode symbol:

Point the scan window at the barcode from within the reading range.
Press one of the scan triggers. The imager projects a laser aiming pattern.
Center the symbol within the aiming pattern. Ensure the entire symbol is within the rectangular area formed by the brackets. Wait for the timeout or release the Scan Key to capture the image. A red beam illuminates the symbol, which is then captured and decoded.

Successful Scan Indicators:

If enabled, a good read beep sounds.
If enabled, the GreenSpot projects a green spot directly onto the barcode.
If enabled, the good read indicator at the top left of the display glows solid green.

	Datalogic Memor 12/17 Family Quick Start Guide: Rugged Mobile Computer & Barcode Scanner Get started quickly with the Datalogic Memor 12/17 Family rugged mobile computer and barcode reader. This guide covers unboxing, basic setup, charging, and scanning.
	Datalogic Memor 11 Quick Start Guide: Rugged Mobile Computer A quick start guide for the Datalogic Memor 11 rugged mobile computer, covering setup, charging, SIM/SD card installation, and scanning operations for DL36LT and DL36WF models.
	Datalogic Memor 11 User Manual: Rugged Mobile Computer Guide Comprehensive user manual for the Datalogic Memor 11 rugged mobile computer, detailing features, setup, operation, maintenance, and technical specifications for enterprise use.
	Datalogic Memor K Quick Start Guide: Setup and Operation Quick start guide for the Datalogic Memor K mobile computer. Learn how to unbox, install the battery, charge the device, power it on/off, use the scanner, and install an SD card. Includes device overview and support information.
	Datalogic Memor K20-25 Mobile Computer: Versatile Productivity Explore the Datalogic Memor K20-25, a smart key-based mobile computer designed for efficient data capture in retail, logistics, and healthcare. Features Android 13, a powerful octa-core processor, and robust IP64 protection.
	Datalogic Memor 20 User Manual: Rugged Mobile Computer Guide Comprehensive user manual for the Datalogic Memor 20, a rugged mobile computer with 1D/2D imager. Learn about features, setup, settings, and troubleshooting for enterprise use.
	Datalogic Memor 10 Rugged Mobile Computer User's Manual Comprehensive user manual for the Datalogic Memor 10 rugged mobile computer, detailing its features, setup, operation, settings, and technical specifications.
	Datalogic Memor 12 Safety and Regulatory Addendum Comprehensive safety, regulatory compliance, and operational guidelines for the Datalogic Memor 12 rugged mobile computer, including battery, laser, RF exposure, FCC, ISED, EU, and UKCA compliance information.