Danfoss ECL Comfort 210 Electronic Controller
Specifications:
- Model: ECL Comfort 210 / 296 / 310
- Code Number: A266 (087H3800)
- Input: 230 V a.c.
- Output: 0-10 V, 3-point control
- Current Rating: 4(2) A / 230 V a.c., 0.2 A / 230 V a.c.
Product Usage Instructions
Installation:
- Ensure power supply matches the input requirement (230 V a.c.).
- Connect M1 and M2 to the relevant control points using 3-point or 0-10 V connections as needed.
A266, ECA 32
| 0 – 10 V: | ||
| M1 | M2 | |
| A266.1 | ✓ | ✓ |
| A266.2 | ✓ | |
| A266.9 | ✓ | ✓ |
| A266.10 | ✓ | ✓ |
ECL Comfort 210 / 296 / 310: 230 V a.c.
Configuration
Refer to the installation guide for specific configurations based on the model and version of the ECL Comfort device.
ECL Comfort 210 / 310
ECL Comfort 296
230 V a.c. , A266.1 / A266.2 / A266.9 / A266.10
230 V a.c. , A266.1 / A266.2 / A266.9 / A266.10
A266, ECL Comfort 310
ECA 32, V1, V2
Operation
- Power on the device after installation.
- Set the desired parameters for temperature control using the provided controls.
230 V a.c. / 24 V a.c. , safety thermostat
1-step closing
2-step closing
ECL Comfort 310: 24 V a.c.
24 V a.c. (A266.1 / A266.2 / A266.9 / A266.10)
Pt 1000 (1000 Ω / 0 °C)
A266.1 / A266.2 / A266.9 / A266.10
A266.1 / A266.2 / A266.10
A266.2 / A266.9 / A266.10
S8
A266.9
ECA 30 / 31
Master / slave
Modbus
M-bus
Pt 1000 (IEC 751B, 1000 Ω / 0 °C)
ECA 30
ECL Comfort 296
ECL Comfort 210 / 310
Maintenance:
Regularly check and clean the device to ensure proper functioning. Refer to the maintenance section of the user manual for detailed instructions.
ECL Comfort 210 / 296 / 310, A266: www.heating.danfoss.com
https://www.youtube.com/user/DanfossHeating
-> Playlists -> How-to Videos -> District Energy installation videos
Danfoss A/S
Heating Segment
- danfoss.com
- +45 7488 2222
- E-Mail: heating@danfoss.com
Danfoss can accept no responsibility for possible errors in catalogues, brochures and other printed material. Danfoss reserves the right to alter its products without notice. This also applies to products already on order provided that such alterations can be made without sub sequential changes being necessary in specifications already agreed. All trademarks in this material are property of the respective companies. Danfoss and all Danfoss logotypes are trademarks of Danfoss A/S. All rights reserved.
© Danfoss | DHS-SMDT/DK | 2020.11
FAQ
- Q: What is the input voltage requirement for the ECL Comfort devices?
A: The input voltage requirement is 230 V a.c. - Q: What type of control outputs are supported by the ECL Comfort devices?
A: The devices support 0-10 V and 3-point control outputs. - Q: How do I configure the ECL Comfort device for specific temperature control?
A: Refer to the installation guide for detailed configuration instructions based on the model and version of the device.
Documents / Resources
 |
Danfoss ECL Comfort 210 Electronic Controller [pdf] Installation Guide ECL Comfort 210, ECL Comfort 210 Electronic Controller, Electronic Controller, Controller |
 |
Danfoss ECL Comfort 210 Electronic Controller [pdf] Installation Guide ECL Comfort 210, ECL Comfort 210 Electronic Controller, Electronic Controller, Controller |
 |
Danfoss ECL Comfort 210 Electronic Controller [pdf] Installation Guide ECL Comfort 210, ECL Comfort 210 Electronic Controller, Electronic Controller, Controller |
