CISUN LIGHTING K-8000C LED Digital Controller Instruction Manual

Eight ports output, each supporting up to 512/1024 lights (DMX
lights can support up to 512 pixels).
Playback content stored in SD card, supporting up to 32 files
with SD card capacities ranging from 128MB to 32GB.

The controller can be used singly or cascaded with multiple
controllers for optical isolation support.

Appearance Picture:

Include screen print meanings and button functionalities for
different operations.

Wiring Instructions:

Guidelines for wiring the controller with conventional IC lamps
and support for DMX lights coding and wiring methods.

Encryption Glossary Explanation:

Explanation of password-related terms and actions like setting
passwords, clearing passwords, and password expiration.

Frequently Asked Questions (FAQ)

Q: How many files can the SD card store?

A: The SD card can store up to 32 files with capacities ranging
from 128MB to 32GB.

Q: How many lights can each port support?

A: Each port can support up to 512/1024 lights, with DMX lights
having the capability to support up to 512 pixels.

“`

View Fullscreen

K-8000C Manual
K-8000C system features:
1. 32 to 65536 degree Gray control, Gamma correction procession handle. 2. Support various point, line light source, and all kinds of rules and specific shaped handle. 3. The controller has eight ports output, each port can support up to 512/1024 lights(DMX
lights can support up to 512 pixels). 4. The playback content stored in SD card, the SD card can store up to 32 files, SD cared
capacity supports 128MB-32GB. 5. The controller can single set use,also multiple controllers cascade, cascade optical isolation
mode: interference, better stability, cascade distance between two controllers can reach up to 150 meters, need to use 0.5M² pure copper power cord. 6. The controller support chip can lock the support IC in software, or not lock the support IC in the software, select the support IC through the controller CHIP button, this scheme is more flexible and convenient. 7. For the DMX lighting IC, the controller comes with write address function; In addition, with use of our 2016 LedEdit-K V3.26 or later edition can make one key write address function setting. 8. Support load lamp is 4 channels (RGBW) pixels, or split into single channel point pixels. 9. Enhanced 485 TTL and 485 differential (DMX) signal output. 10. The controller comes with the test effects were as follows: 1 red, green, blue and black jump; 2 red, green, blue and black gradient; 3 red, green, blue and goes. Note: 1. The controller load lamps 512 points pixel, speed can reach up to 30 frames / sec, 768 point pixel speed can reach up to 25 frames / sec, 1024 point pixel speed is about 22 frames / sec (the above parameter is an example of 1903 agreement IC, different IC have difference) 2. International standard DMX512 (1990 agreement) maximum support 512 pixels. When the load is international standard 170 pixels, the speed can reach up to 30 frames / sec, 340 pixels speed is about 20 frames / sec, when 512 pixels speed is about 12 frames / sec. 3. Timing (holidays) Play Global Wireless GPS synchronization, control station channel distributor, please contact the salesman or technical support staff for more information.

Support chips (PC Software Select K-8000-RGB) 00: UCS1903,1909,1912,2903,29042909,2912TM1803,1804,1809,1812
SM1670316709,16712WS2811INK1003LX3203,1603,1103GS8205, 8206SK6812Support up to 1024*8=8192 pixels 01SM16716,16726Support up to 1024*8=8192 pixels 02P9813Support up to 1024*8=8192 pixels 03LPD6803Support up to 1024*8=8192 pixels 04LX1003,1203Support up to 1024*8=8192 pixels 05WS2801Support up to 1024*8=8192 pixels 06LPD1886Support up to 1024*8=8192 pixels 07TM1913Support up to 1024*8=8192 pixels 08TM1914Support up to 1024*8=8192 pixels 09P9883,P9823Support up to 1024*8=8192 pixels 10DMXSupport up to 512*8=4096 pixels, suggest to support 320*8=2560 pixels 11DMX 500KSupport up to 512*8=4096 pixels, suggest to support 320*8=2560 pixels 12DMX 250K-CZF Support up to 512*8=4096 pixels, suggest to support 320*8=2560 pixels 13DMX 250K-CZF Support up to 512*8=4096 pixels, suggest to support 320*8=2560 pixels
NOTES: 1. If support RGBW four channels’ lights should select K-8000-RGBW. 2. If support single channel light should choose K-8000-W, at this time, one channel means one pixel, the software effect make as white lighting. Appearance Picture:

Screen print meaning

Button meaning: Button
SHIP MODE SPEED+ SPEED-

Meaning
Select chip model Switch files Speed up Speed down

Press CHIP and then MODE button, can enter write code mode, 61 means UCS512-A/B coding; 62 means WS2821 coding; 63 means SM512 coding, 64 means UCS512-C coding
Press SPEED+ and SPEED- the same time, would enter effect files looping mode

Power supply POWER SYNC STATUS SD CARD

DC5V input/DC12-24 input Power indicator Cascade indicator Status indicator SD card slot

Signal outputTTL/245 signal

GND

GND(negative electrode

DAT

Data

CLK

Clock

Signal outputDMX512 signal

GND A/DAT+ B/DATADDR

GND(negative electrode Signal + Signal Coding line

The corresponding frame rate of speed level

Speed Level 1 2 3 4 5 6 7 8

Frame Rate/Sec 4 frame 5 frame 6 frame 7 frame 8 frame 9 frame 10 frame 12 frame

Speed Level 9 10 11 12 13 14 15 16

Frame Rate/Sec 14 frame 16 frame 18 frame 20 frame 23 frame 25 frame 27 frame 30 frame

Conventional IC lamps wiring:
Controller support DMX lights coding and wiring method: Two signal wiring diagram:

Single signal wiring diagram:
1.Like the above diagram, wired the line and start the controller, press “CHIP”and “MODE” at the same time switch to coding mode, adjust to Chip: 61 that is UCS512A or B coding mode, as below:
NOTE: 61 means UCS512A or B coding mode; 62 means WS2821 coding mode; 63 means SM DMX512AP; 64 means UCS512-CCh.03 means the coding channel is 3 channels

2. After selection, press “MODE” to code, then the screen would display A A A. Until finished coding, it would show Writing OK, Like below:
3After finished address code, press “CHIP” first and at the same time press “MODE”button, switch to playback mode, switch the chip to Chip: 10, this is the DMX512 standard agreement 250K playback mode. At this time, press MODE button and SPEED button can separately switch playback mode and adjust speed, as below:
Special RemarksDerived program after set one-key coding in the software, long press MODE for 5 seconds can write code to the lights directly, this function is very convenient and practical. Welcome to consult our engineer or salesman to learn the detailed operation method.

Encryption Glossary Explanation:
Password is OK Num Password exist Can’t repeated Set Password OK Clear Pwd OK Pwd not right No Password Has expired! Contact factory

Password normal!
The remaining boot times
Password has existed Can’t repeat set password Password set successfully
Clear password successfully
Password not correct Password don’t exist Password expired, please contact the factory!

Specific parameter: Memory card:
Type: SD card Capacity: 128MB–32GB FormatFAT or FAT32 format Storage files: *.led Physical parameter: Working temperature-20–85 Working powerDC 5V or DC 12-24V input Power consumption: 5W Weight: 0.8Kg Size:

Notes: 1. To copy files to SD card, you must format the SD card first, pay attention to is that each copy must be formatted first. 2. SD card must be formatted as FAT form or FAT32 form. 3. The SD card can not be hot-swappable, plug the SD card each time, you must first disconnect the power supply controller.

How to handle the common problems:
Problem 1: After powered on, the controller screen display SD Error, and no effect output. Answer: The screen display SD Error means the controller did not read the SD card correctly, the exist problems as below: SD card is empty, has no effect files. The effect files *.led in SD card and the controller model is mismatch, please select correct controller model, chip model in the latest edition 2016LedEdit, and remake effect files *.led. Change SD card and then retesting, rule out the possibility of SD card is broken.
Problem 2: After powered on, the indicator is normal, but the lamps has no effects change. Answer: It has the following reasons for this problems: Please check if the signal line of the lamps and the controller connected correctly. Conventional lamps signal divided into input and output, please confirm whether the controller connected the first lamp’s signal input.
Problem 3: After connect the lamps and the controller, the lamps is strobe and has effect change, at the same time the controlled indicator shows normal.
Answer: The ground line of the controller and the lamps are not connected. The effects in SD are not correct. The IC of the lamps when making effect is not corresponding with the IC of the actual lamps. If did not lock the chip, when making effects in the software, need to press the controller chip to the light’s corresponding chip, about press to which number, please refer to the sticker IC order on the controller. The power supply voltage of the lamps is insufficient.
Problem 4 SD card can not be formatted. AnswerFirstly, make sure if the protection switch on the side of SD card is unlocking. The unlocking direction is the gold needle side of SD card. The protection has designed as required, but can not formatted, if this condition appears, it always because the SD card reader is broken, please change the SD card reader(had better use good quality card reader, SSK card reader is suggested). If the above operations can not solve the formatting problems, please change the SD card and retest.

Documents / Resources

CISUN LIGHTING K-8000C LED Digital Controller [pdf] Instruction Manual
K-8000C, K-8000C LED Digital Controller, K-8000C, LED Digital Controller, Digital Controller, Controller

References

User Manual

K-8000C LED Digital Controller

Product Specifications

Product Usage Instructions

System Features: