AVARRO 0E-HDMIMX4 API Command Set HDMI Switcher
RS232 Default Setting
| Parameters | Value |
| Baud Rate | 115200 bps |
| Data bits | 8 bits |
| Parity | None |
| Stop bits | 1 bit |
| Flow control | None |
About Telnet Connection
Before the process of sending the telnet command, shall make telnet connection to the corresponding device.
The form of telnet command is as follow:
- telnet ip (port)
- ip: The unit’s IP address.
- port: The unit’s port number, this is non-required on some Telnet control tools or platforms. If required, port number is 23 by default.
Example: If the unit’s IP address is 192.168.11.143,
The telnet command is telnet 192.168.11.143
Command
Take Command SET SW in out<CR><LF> as an example:
- [SET SW] denotes command key words, case insensitive.
- [in out] denotes parameters, case insensitive; incorrect parameters number will not be recognized.
- <CR><LF> denotes a carriage return or a line feed; all commands must be ended up with a carriage return or a line feed.
| No. | Description | Command | Example |
| Normal switch case | |||
| Command: SET SW in out<CR><LF> | Command: SET SW hdmiin1 hdmiout2<CR><LF> | ||
| Return: SW in out<CR><LF> | Return: SW hdmiin1 hdmiout2<CR><LF> | ||
|
1 |
Switch Input for Output | Parameter: in = {hdmiin1, hdmiin2…hdmiin4}; out = {hdmiout1, hdmiout2…hdmiout4}; |
Description: Switch input 1 for hdmi output 2 |
| Description: SW is short for Switch Switch one input source for one output sink | |||
| Command: SET SW in all<CR><LF> | Command: SET SW hdmiin1 all <CR><LF> | ||
|
2 |
Switch indicate input for all output |
Return: SW in all <CR><LF>
Parameter: in = { hdmiin1, hdmiin2… hdmiin4}; all = {all}; |
Return: SW hdmiin1 all<CR><LF>
Description: Switch input1 for all output sink |
| Description: SW is short for Switch Switch one input source for all output sink | |||
| No. | Description | Command | Example |
| Command: GET MP out<CR><LF> | Command: GET MP hdmiout1<CR><LF> | ||
| 3 | Get which input mapping to the indicate Output | Return: Mp in out<CR><LF>
Parameter: in = {hdmiin1, hdmiin2…hdmiin4}; out = {hdmiout1, hdmiout2…hdmiout4}; |
Return: MP hdmiin2 hdmiout1<CR><LF>
Description: Get which input mapping to output 1 |
| Description: MP is short for mapping
Get which input mapping to the indicate Output |
|||
| Command: GET MP all<CR><LF> | Command: GET MP all
<CR><LF> |
||
| 4 | Get which output mapping to all input | Return: MP in out<CR><LF> MP in out<CR><LF>
……
Parameter: in = {hdmiin1, hdmiin2…hdmiin4}; out = {hdmiout1, hdmiout2…hdmiout4}; all = {all}; |
Return: MP hdmiin1 hdmiout1<CR>… MP hdmiin2 hdmiout2<CR><LF>
……
Description: Get which output mapping to all input |
| Description: MP is short for mapping Get which output mapping to all input |
| No. | Description | Command | Example |
| CEC Control | |||
| Command: SET CEC_PWR out prm<CR><LF> | Command: SET CEC_PWR hdmiout1 on<CR><LF> | ||
|
1 |
Set CEC POWER ON/OFF |
Return: CEC_PWR out prm<CR><LF>
Parameter: prm = {on, off} out = {hdmiout1, hdmiout2…hdmiout4, all} |
Return: CEC_PWR hdmiout1 on<CR><LF> Description: Set sink hdmi output 1 power on |
| Description: Set sink power on or off | |||
| Command:
SET AUTOCEC_FN out prm<CR><LF> |
Command: SET AUTOCEC_FN hdmiout1 on<CR><LF> | ||
|
2 |
Set CEC AUTO POWER ON/OFF |
Return: AUTOCEC_FN out prm<CR><LF>
Parameter: prm = {on, off} out = {hdmiout1, hdmiout2…hdmiout4}; |
Return: AUTOCEC_FN hdmiout1 on<CR><LF> Description: Set sink hdmi output 1 auto power ON |
| Description: Set sink auto power Function ON or OFF | |||
| No. | Description | Command | Example |
| Command: GET AUTOCEC_FN out<CR><LF> | Command: GET AUTOCEC_FN hdmiout1<CR><LF> | ||
| Return: AUTOCEC_FN out prm<CR><LF> | Return: AUTOCEC_FN on | ||
| 3 | Get CEC AUTO POWER ON/OFF
Status |
Parameter: prm = {on, off} out = {hdmiout1, hdmiout2…hdmiout4}; |
Description: Get Sink auto power status, and the status is ON. |
| Description: Get Sink auto power Function ON or OFF Status.
Default: Off |
|||
| Command: SET AUTOCEC_D out prm<CR><LF> | Command: SET AUTOCEC_D hdmiout1 2<CR><LF> | ||
| 4 | Set CEC POWER Delay Time | Return: AUTOCEC_D out prm<CR><LF>
Parameter: out = {hdmiout1,hdmiout2…hd miout4}; prm = {1,2,3…,}// according to the actual time counter,1 means 1 minute ,2 means 2 minutes, Default wait time is 2 minutes, Max wait time is 30 minutes. |
Return: AUTOCEC_D hdmiout1 2<CR><LF>
Description: when no active signal to hdmi1, 2 minutes later, the unit will auto power off. |
| Description: AUTOCEC_D is short for CEC auto Power Delay Timing |
| No. | Description | Command | Example |
| Command: GET AUTOCEC_D out
<CR><LF> |
Command: GET AUTOCEC_D hdmiout1 <CR><LF> | ||
| Return: AUTOCEC_D out prm<CR><LF> | Return: AUTOCEC_D hdmiout1 2 <CR><LF> | ||
| 5 | Get CEC POWER Delay Time Status | Parameter: out = {hdmiout1,hdmiout2…hd miout4}; |
Description: |
| Description: AUTOCEC_D is short for CEC auto Power Delay Timing | |||
| Default: 2 |
| No. | Description | Command | Example |
| HDCP | |||
| Command: SET HDCP_S in prm<CR><LF> | Command:
SET HDCP_S hdmiin1 on<CR><LF> |
||
| 1 | Set Input HDCP support ON/OFF | Return: HDCP_S in prm<CR><LF>
Parameter: prm = {on, off} in = {hdmiin1, hdmiin2…hdmiin4} |
Return: HDCP_S hdmiin1 on<CR><LF> Description: Set hdmi input 1 hdcp support on |
| Description: HDCP_S will control source hdcp support on or off | |||
| Command: GET HDCP_S in <CR><LF> | Command: GET HDCP_S hdmiin1<CR><LF> | ||
| Return: HDCP_S in prm<CR><LF> | Return: HDCP_S hdmiin1 on<CR><LF> | ||
|
2 |
Get Input HDCP support ON/OFF Status | Parameter: prm = {on, off} in = {hdmiin1, hdmiin2…hdmiin4} | Description: Get hdmi1 hdcp support on or off status, and the result is on |
| Description: HDCP_S is short for HDCP support | |||
| Default: on | |||
| No. | Description | Command | Example |
| EDID | |||
| 1 | Set Input EDID | Command:
SET EDID in prm<CR><LF> Return: EDID in prm<CR><LF> Parameter: in = {hdmiin1, hdmiin2…hdmiin4}; prm = {1 ~12} 01: Copy form output 1 02: Copy form output 2 03: Copy form output 3 04: Copy form output 4 05 : 4K@60Hz 5.1ch audio With HDR 06: 4K@60Hz 2.0ch audio With HDR 07: 4K@30Hz 7.1ch audio With HDR 08: 4K@30Hz 5.1ch audio With HDR 09: 4K@30Hz 2.0ch audio With HDR 10: 4K@30Hz/8bit only 2.0ch audio Without HDR 11: 1080P@60Hz 2.0ch audio … 12: Smart EDID |
Command: SET EDID hdmiin1 10<CR><LF>
Return: EDID hdmiin1 10<CR><LF> Description: Set in1 EDID Fix 4K@30Hz/8bit only 2.0ch audio Without HDR |
|
Description: Set Input EDID |
|||
| No. | Description | Command | Example |
| 2 | Get All Input EDID status | Command: GET EDID all <CR><LF>
Return: EDID in prm<CR> EDID in prm<CR> EDID in prm<CR><LF> …… Parameter: in = {hdmiin1, hdmiin2…hdmiin4}; prm = {1 ~13} 01: Copy form output 1 02: Copy form output 2 03: Copy form output 3 04: Copy form output 4 05 : 4K@60Hz 5.1ch audio With HDR 06: 4K@60Hz 2.0ch audio With HDR 07: 4K@30Hz 7.1ch audio With HDR 08: 4K@30Hz 5.1ch audio With HDR 09: 4K@30Hz 2.0ch audio With HDR 10: 4K@30Hz/8bit only 2.0ch audio Without HDR 11: 1080P@60Hz 2.0ch audio … 12: Smart EDID 13: EDID Write |
Command: GET EDID all
<CR><LF>
Return: EDID hdmiin1 01<CR> EDID hdmiin2 02<CR> EDID hdmiin3 03<CR><LF> ……
Description: Get all input EDID Status |
| Description: Get all input EDID Status | |||
| Default: 5 |
| No. | Description | Command | Example |
| 3 | Get one input EDID Status | Command: GET EDID in <CR><LF>
Return: EDID in prm<CR><LF> Parameter: in = {hdmiin1, hdmiin2… hdmiin4}; prm = {1 ~13} 01: Copy form output 1 02: Copy form output 2 03: Copy form output 3 04: Copy form output 4 05 : 4K@60Hz 5.1ch audio With HDR 06: 4K@60Hz 2.0ch audio With HDR 07: 4K@30Hz 7.1ch audio With HDR 08: 4K@30Hz 5.1ch audio With HDR 09: 4K@30Hz 2.0ch audio With HDR 10: 4K@30Hz/8bit only 2.0ch audio Without HDR 11: 1080P@60Hz 2.0ch audio … 12: Smart EDID 13: EDID Write |
Command: GET EDID hdmiin1<CR><LF>
Return: EDID hdmiin1 10<CR><LF>
Description: Get in1 edid status, and the status is Fix 4K@30Hz/8bit only 2.0ch audio Without HDR |
| Description: Get one input EDID Status | |||
| Default: 5 |
| No. | Description | Command | Example |
| System Info | |||
| Command: RESET<CR><LF> | Command: RESET<CR><LF> | ||
|
1 |
Factory reset |
Return: RESET<CR><LF> | Return:
ESET<CR><LF> |
| Description:
Factory reset |
Description:
Factory reset all board |
||
| Command: REBOOT<CR><LF> | Command: REBOOT<CR><LF> | ||
|
2 |
System reboot |
Return: REBOOT<CR><LF> | Return: REBOOT<CR><LF> |
| Description: System reboot | Description: System reboot | ||
| Command: help<CR><LF> | Command: help<CR><LF> | ||
| 3 | Get the API list | ||
| Description: Get the API list | Description: Get the API list | ||
| Command: SET IP MODE pcm<CR><LF> | Command:
SET IP MODE dhcp<CR><LF> |
||
| Return: IMODE pcm <CR><LF> | Return: IP MODE dhcp <CR><LF> | ||
| 4 | Set IP Mode | Parameter: pcm= {static, dhcp} | Description: Set IP mode is dhcp |
| Description: Set IP mode | |||
| Default: DHCP | |||
| No. | Description | Command | Example |
| Command: GET IP MODE<CR><LF> | Command: GET IP MODE<CR><LF> | ||
| Return: IP MODE pcm <CR><LF> | Return: IP MODE dhcp <CR><LF> | ||
| 5 | Get IP Mode | Parameter: pcm= {static, dhcp} | Description: IP mode is dhcp |
| Description: Get IP mode | |||
| Default: DHCP | |||
| Command: | Command: | ||
| SET IPADDR | SET IPADDR | ||
| xx.xx.xx.xx | 192.168.1.4 | ||
| xx.xx.xx.xx | 255.255.255.0 | ||
| xx.xx.xx.xx<CR><LF> | 192.168.1.1<CR><LF | ||
| > | |||
| Return: | |||
| IPADDR IP:xx.xx.xx.xx | Return: | ||
|
6 |
SET IP
address |
MASK: xx.xx.xx.xx GATE:
xx.xx.xx.xx<CR><LF> |
IPADDR IP:192.168.1.4
MASK:255.255.255.0 |
| GATE:192.168.1.1[< | |||
| Description: | CR><LF> | ||
| SET IP address | |||
| Description: | |||
| Set IP address is | |||
| 192.168.1.4, MASK is | |||
| 255.255.255.0, | |||
| GATE is 192.168.1.1 |
| No. | Description | Command | Example |
| Command: GET IPADDR<CR><LF> |
Command: GET IPADDR<CR><LF> |
||
| 7 | GET IP address | Return:
IPADDR IP:xx.xx.xx.xx MASK: xx.xx.xx.xx GATE: xx.xx.xx.xx<CR><LF>
Description: |
Return: IPADDR IP:192.168.1.4
MASK:255.255.255.0 GATE:192.168.1.1<C R><LF> |
| Description: Get IP address is 192.168.1.4, MASK is 255.255.255.0, GATE is 192.168.1.1 |
|||
| Update info | |||
| Command: GET VER<CR><LF> |
Command: GET VER<CR><LF> |
||
| 1 | Get selected target firmware version | Return: VER prm<CR><LF> Parameter: Description: |
Return: MX0404_N201_000 VER 1.0, ARM VER 1.0<CR><LF>
Description: Get all module firmware version |
| Command: UPG [prm] <CR><LF> |
Command: UPG MASTER<CR><LF> |
||
| 2 | Upgrade module | Return: UPG [prm] <CR><LF>
Parameter: |
Return: UPG MASTER<CR><LF> |
| Description: Upgrade module |
Description: upgrade module |
||
| No. | Description | Command | Example |
| Preset scene | |||
| Command: SAVE PRESET prm<CR><LF> | Command: SAVE PRESET 1<CR><LF> | ||
|
1 |
Save Preset Scene |
Return: PRESET prm<CR><LF> |
Return: PRESET 1 <CR><LF> |
| Parameter: prm = {1,2,3}// |
Description: Save preset scene |
||
| Description: Save Preset Scene |
|||
| Command: RESTORE PRESET prm<CR><LF> | Command: RESTORE PRESET 1<CR><LF> | ||
| Return: PRESET prm<CR><LF> |
Return: PRESET 1<CR><LF> |
||
|
2 |
Restore Preset Scene |
Parameter: prm = {1,2,3}// Description: |
Description: Restore preset scene |
| Default: mp hdmiin1 hdmiout1 mp hdmiin2 hdmiout2 mp hdmiin3 hdmiout3 mp hdmiin4 hdmiout4 |
|||
| No. | Description | Command | Example |
| Audio | |||
| Command: SET MUTE out pcm<CR><LF> | Command: SET MUTE audioout1 on<CR><LF> | ||
| Return: MUTE out pcm<CR><LF> | Return: MUTE audioout1 on<CR><LF> | ||
|
1 |
Set Audio Output mute |
Parameter: pcm = {on, off};//on means mute; off means unmute out = {audioout1, audioout2,…audioout4, all}; |
Description: Set audioout1 mute on |
| Description: Set Audio mute or not mute | |||
| Command: GET MUTE out<CR><LF> | Command: GET MUTE
audioout1<CR><LF> |
||
| Return: MUTE out pcm<CR><LF> | Return: MUTE audioout1 off<CR><LF> | ||
| 2 | Get Audio Output mute status | Parameter: pcm = {on, off};;//on means mute; off means unmute out = {audioout1, audioout2,…audioout4, all}; | Description: Get Audio Output mute status. |
| Description: Get Audio Output mute status | |||
| Default: off | |||
| No. | Description | Command | Example |
| Scaler | |||
| Command: SET SCALER out pcm<CR><LF> | Command: SET SCALER hdmiout1 on<CR><LF> | ||
| Set video Output scaler | Return: SCALER out pcm<CR><LF>
Parameter: pcm = {on, off};//on means scaler; off means not scaler out = {hdmiout1, hdmiout2,…hdmiout4, all }; Description: Set Video scaler or not scaler |
Return: SCALER hdmiout1 on<CR><LF> Description: Set hdmiout1 scaler on |
|
| Command: GET SCALER out<CR><LF> | Command: GET SCALER hdmiout1<CR><LF> | ||
| Return: SCALER out pcm<CR><LF> | Return: SCALER hdmiout1 on<CR><LF> | ||
|
2 |
Get video Output scaler status |
Parameter:
pcm = {on, off};;//on means mute; off means unmute out = {hdmiout1,hdmiout2,… hdmiout4, all}; |
Description: Get video Output scaler status. |
| Description: Get video Output scaler status | |||
| Default: on | |||
Documents / Resources
 |
AVARRO 0E-HDMIMX4 API Command Set HDMI Switcher [pdf] User Guide 0E-HDMIMX4, 0E-HDMIMX4 API Command Set HDMI Switcher, 0E-HDMIMX4, 0E-HDMIMX4 HDMI Switcher, API Command Set HDMI Switcher, Set HDMI Switcher, HDMI Switcher, Switcher |
