PW KEYPAD-XK1 Access Systems
Instruction Manual 
PW KEYPAD-XK1 Access Systems
PW KEYPAD-XK1 & XK4
SPECIFICATIONS:
Voltage: 12-28V AC/DC
Standby Current: 50mA
Operating Current: 120mA
Up to 999 users code & tags
IP66 Rated
Built in Prox Reader
Relay Reset time: 1-300sec. or ON/OFF (toggle) Mode 
Check www.aap.co.nz/xk1 for more information
ENTERING ADMIN MODE:
To enter programming mode press * (admin code) #. 
Default admin code is: 888888.
The keypad will automatically time out after 30 seconds.
EXITING ADMIN MODE:
To Exit admin mode simply press :
ADDING USER CODES & PROX TAGS:
You can have up to 999 user codes and prox tags assigned to either Relay 1 or 2.
These are loaded at program address 11 then user slot (1 to 999) a user slot can have a code and/or a prox tag.
First you must be in Admin Mode. 
Note. If both 1 and 2 are pressed under Relay No. both relays 1 and 2 will operate.
Document the programmed user slots in the back of this paperwork.
DELETING USER CODES & PROX TAGS:
You can only delete a user code by knowing the user slot it is stored under.
First you must be in Admin Mode.
Prox Tags can either be deleted by slot number (same as above) or by presenting them (see below)
First you must be in Admin Mode.
Note. Multiple Prox Tags can be deleted in this was one after another.
To Delete All user slots follow the process below.
First you must be in Admin Mode.
RELAY 1 RESET TIME: (default 5sec)
Relay 1 reset time can be set from 1 to 300 seconds. If 0 is selected the relay will toggle on & off.
To change reset time you must be in Admin Mode.
RELAY 2 RESET TIME: (default 5sec)
Relay 2 reset time can be set from 1 to 300 seconds. If 0 is selected the relay will toggle on & off.
To change reset time you must be in Admin Mode.
CHANGING ADMIN CODE:
To change Admin code you much be in Admin Mode first. 
Advance Programming Options
For all programming addresses below you must first be in Admin Mode. 
KEYPAD BACKLIGHT: (default always On) 
Buzzer Volume: (default level 3)
DOOR BELL FEATURE: (Pressing 0 # triggers Relay 2) Note feature won’t work if users are assigned to relay 2.
DOOR OPEN TOO LONG FEATURE: (requires reed switch connected between Brown & Grey wire). 
DOOR FORCED FEATURE: (requires reed switch connected between Brown & Grey wire).
TAMPER ALARM: 
FACTORY RESET:
This will erase timers, options and admin code. (note the user codes and tags are kept in memory)
Power Down the keypad, press and hold 
then Power Up the keypad (keeping the * button pressed)
= Keypad has successfully reset
USER OPERATION:
| SLOT | NAME | CODE | Relay 1 | Relay 2 | TAG |
| 001 | |||||
| 002 | |||||
| 003 | |||||
| 004 | |||||
| 005 | |||||
| 006 | |||||
| 007 | |||||
| 008 | |||||
| 009 | |||||
| 010 | |||||
| 011 | |||||
| 012 | |||||
| 013 | |||||
| 014 | |||||
| 015 | |||||
| 016 | |||||
| 017 | |||||
| 018 | |||||
| 019 | |||||
| 020 | |||||
| 021 | |||||
| 022 | |||||
| 023 | |||||
| 024 | |||||
| 025 | |||||
| 026 | |||||
| 027 | |||||
| 028 | |||||
| 029 | |||||
| 030 | |||||
| 031 | |||||
| 032 | |||||
| 033 | |||||
| 034 | |||||
| 035 | |||||
| 036 | |||||
| 037 | |||||
| Admin |
Go to www.aap.co.nz/xk1 for more wiring diagrams and Information. 
Arrowhead Alarm Products ltd.
1A Emirali Road, Silverdale 0932,
Auckland, NZ Ph. 09 414 0085
www.aap.co.nz
v1.01
Documents / Resources
 |
Arrowhead Alarm Products PW KEYPAD-XK1 Access Systems [pdf] Instruction Manual PW KEYPAD-XK1 Access Systems, PW KEYPAD-XK1, Access Systems |
