AOC 16T20 LCD Monitor
Safety
National Conventions
The following subsections describe notational conventions used in this document.
Notes, Cautions, and Warnings
- Throughout this guide, blocks of text may be accompanied by an icon and printed in bold type or in italic type. These blocks are notes, cautions, and warnings, and they are used as follows:
- NOTE: A NOTE indicates important information that helps you make better use of your computer system.
- CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem.
- WARNING: A WARNING indicates the potential for bodily harm and tells you how to avoid the problem. Some warnings warning is mandated by regulatory authority.
Power
The monitor should be operated only from the type of power source indicated on the label. If you are not sure of the type of power supplied to your home, consult your dealer or local power company.
Unplug the unit during a lightning storm or when it will not be used for long periods of time. This will protect the monitor from damage due to power surges.
The wall socket shall be installed near the equipment and shall be easily accessible.
Installation
- Do not place the monitor on an unstable cart, stand, tripod, bracket, or table- If the monitor falls, it can injure a person and cause serious damage to this product- Use only a cart, stand, tripod, bracket, or table recommended by the manufacturer or sold with this product-
- Follow the manufacturer’s instructions when installing the product and use mounting accessories recommended by the manufacturer A product and cart combination should be moved with care-
- Never push any object into the slot on the monitor cabinet. It could damage circuit parts causing a fire or electric shock. Never spill liquids on the monitor.
- Do not place the front of the product on the floor.
- If you mount the monitor on a wall or shelf, use a mounting kit approved by the manufacturer and follow the kit instructions.
- Leave some space around the monitor as shown below. Othemise, air-circulation may be inadequate hence overheating may cause a fire or damage to the monitor.
- To avoid potential damage, for example the panel peeling from the bezel, ensure that the monitor does not tilt downward by more than -5 degrees- If the -5 degree downward tilt angle maximum is exceeded, the monitor damage will not be covered under warranty.
- See below the recommended ventilation areas around the monitor when the monitor is installed on the wall or on the stand:
Cleaning
Clean the cabinet regularly with cloth. You can use soft-detergent to wipe out the stain, instead of strong-detergent which will cauterize the product cabinet.
When cleaning, make sure no detergent is leaked into the product. The cleaning cloth should not be too rough as it will scratch the screen surface.
Please disconnect the power cord before cleaning the product.
Other
- If the product is emitting a strange smell, sound or smoke, disconnect the power plug IMMEDIATELY and contact a Service Center.
- Make sure that the ventilating openings are not blocked by a table or curtain.
- Do not engage the LCD monitor in severe vibration or high-impact conditions during operation.
- Do not knock or drop the monitor during operation or transportation.
Setup
Contents in Box*Not all signal cables will be provided for all countries and regions. Please check with the local dealer or AOC branch office for confirmation.
Setup Stand & Base
Please setup or remove the base following the steps as below.
Setup
Remove
Adjusting Viewing Angle
For optimal viewing it is recommended to look at the full face of the monitor, then adjust the monitor’s angle to your own preference.
Hold the stand so you will not topple the monitor when you change the monitor’s angle.
You are able to adjust the monitor as below: NOTE:
Do not touch the LCD screen when you change the angle. It may cause damage or break the LCD screen.
Warning
- To avoid potential screen damage, such as panel peeling, ensure that the monitor does no t tilt downward by more than -5 degrees.
- Do not press the screen while adjusting the angle of the monitor. Grasp only the bezel.
Connecting the Monitor
- Mini HDMI
- USB C
- Earphone
Connect to PC
- Connect the power adaptor to the back of the display firmly.
- Turn off your computer and unplug its power cable.
- Connect the display signal cable to the video connector on the back of your computer.
- Plug the power cord of your computer and the power adaptor of your display into a nearby outlet.
- Turn on your computer and display.
If your monitor displays an image, installation is complete. If it does not display an image, please refer Troubleshooting.
To protect equipment, always turn off the PC and LCD monitor before connecting.
Wall Mounting
Preparing to Install An Optional Wall Mounting Arm.
This monitor can be attached to a wall mounting arm you purchase separately. Disconnect power before this procedure.
Follow these steps:
- Follow the manufacturer’s instructions to assemble the wall mounting arm.
- Place the wall mounting arm onto the back of the monitor. Line up the holes of the arm with the holes in the back of the monitor.
- Insert the 2 screws into the holes and tighten.
- Reconnect the cables. Refer to the user’s manual that came with the optional wall mounting arm for instructions on attaching it to the wall.
Noted: Always contact manufacturer for wall-mount installation.(For models with wall mount)
WARNING:
- To avoid potential screen damage, such as panel peeling, ensure that the monitor does not tilt downward by more than- 5 degrees.
- Do not press the screen while adjusting the angle of the monitor. Grasp only the bezel.
Adjusting
Hotkeys Menu/Enter
Press to display the OSD or confirm the selection.
- Power
Press the Power button to turn on the monitor. - Volume
When there is no OSD, press key to open Volume function,then presskey to select Volume.
- Game Mode
When there is no OSD, press “V” key to open game mode function, then presskey to select game mode (FPS,
RTS, Racing, Gamer 1, Gamer 2 or Gamer 3) basing on the different game types. - Source/Exit
When the OSD is closed, press Source/Exit button will be Source hot key function. - OSD Setting
Basic and simple instruction on the control keys.Press the
MENU-button to activate the OSD window.
Press A UpDown to navigate through the functions. Once the desired function is highlighted, press the MENU button to activate it, press
V Down to navigate through the sub-menu functions. Once the desired function is highlighted, press
MENU-button to activate it.
Press Up or V Down to change the settings of the selected function. Pressto exit. If you want to adjust any other function, repeat steps 2-3.
Notes:
- If the product has only one signal input, the item of “Input Select” is disable to adjust.
- ECO modes (except Standard mode), DCR, DCB mode and Picture Boost, for these four states that only one state can exist.
- If the product input signal resolution is the local resolution, the “Image Ratio” item is invalid.
OSD lock, long press the ” ” button for 10 seconds to lock or unlock the menu.
Luminance
Note:
When HDR Mode” is set to Unon-off, the items “Contrast”, “Eco Mode”, Gamma” cannot be adjusted
Color Setup Picture Boost
Note:
Adjust the brightness, contrast, and position of the Bright Frame for better viewing experience-
When “HDR Mode” under “Luminance” is set to “non-of’, all items under “Picture Boost” cannot be adjusted.
OSD Setup
|
Language |
English |
Select the OSD language. |
Français | |||
Français | |||
Português | |||
Deutsch | |||
Italiano | |||
Nederlands | |||
Svenska | |||
Suomi | |||
Polski | |||
Čeština | |||
Русский | |||
한국어 | |||
Türkçe | |||
Українська | |||
繁體中文 | |||
简体中文 | |||
日本語 | |||
Timeout | 5-120 | Adjust the OSD Timeout. | |
H. Position | 0-100 | Adjust the horizontal position of OSD. | |
V. Position | 0-100 | Adjust the vertical position of OSD. | |
Transparence | 0-100 | Adjust the transparence of OSD. | |
Break Reminder | Break reminder if the user continuously work for more than 1hrs. |
Game SettingNote:
When “Color Setup” under “HDR Mode” is set to “non-off’ , “Game Mode”, “Shadow Control”, “Game Color””Low Blue Mode” items cannot be adjusted.
Extra
Exit
LED Indicator
Status | LED Color |
Full Power Mode | White |
Active-off Mode | Orange |
Troubleshoot
Specification
General Specification
Panel | Model Name | 16T20 | ||
Driving System | TFT Color LCD | |||
Viewable Image Size | 39.5cm diagonal(15.6’’ Wide Screen) | |||
Pixel Pitch | 0.17925mm(H) x 0.17925mm(V) | |||
Others |
Horizontal Scan Range | 30k-85kHz | ||
Horizontal Scan Size(Maximum) | 344.16mm | |||
Vertical Scan Range | 48-75Hz | |||
Vertical Scan Size(Maximum) | 193.59mm | |||
Max Resolution | 1920×1080@60Hz | |||
Plug & Play | VESA DDC2B/CI | |||
External Power Supply Model | CP0154-0503000UA1 | |||
Power Source | 5.0V 3.0A | |||
Power Consumption |
Typical (default brightness and contrast) | 10W | ||
Max. (brightness =100, contrast =100) | ≤15W | |||
Standby mode | ≤0.5W | |||
Dimensions | 354.2×222.4×9.6mm(WxHxD) | |||
Net Weight | 1.1kg | |||
Physical Characteristics | Connector Type | Mini HDMI/USB C | ||
Signal Cable Type | Detachable | |||
Environmental | Temperature | Operating | 0°C~40°C | |
Non-Operating | -25°C~55°C | |||
Humidity | Operating | 10%~85%(non-condensing) | ||
Non-Operating | 5%~93%(non-condensing) | |||
Altitude | Operating | 0m~5000m(0ft~16404ft) | ||
Non-Operating | 0m~12192m(0ft~40000ft) |
Preset Display Modes
STANDARD | RESOLUTION | HORIZONTAL FREQUENCY(KHz) | VERTICAL FREQUENCY(Hz) |
VGA | 640×480@60Hz | 31.469 | 59.940 |
SVGA |
800×600@56Hz | 35.156 | 56.250 |
800×600@60Hz | 37.879 | 60.317 | |
XGA | 1024×768@60Hz | 48.363 | 60.004 |
SXGA | 1280×1024@60Hz | 63.981 | 60.020 |
WSXG |
1280×720@60Hz | 45.000 | 60.000 |
1280×960@60Hz | 60.000 | 60.000 | |
WXGA+ | 1440×900@60Hz | 55.935 | 59.887 |
WSXGA+ | 1680×1050@60Hz | 65.290 | 59.954 |
FHD | 1920×1080@60Hz | 67.500 | 60.000 |
Pin Assignments
Pin No. | Signal Name | Pin No. | Signal Name | Pin No. | Signal Name |
1. | TMDS Data 2+ | 9. | TMDS Data 0- | 17. | DDC/CEC Ground |
2. | TMDS Data 2 Shield | 10. | TMDS Clock + | 18. | +5V Power |
3. | TMDS Data 2- | 11. | TMDS Clock Shield | 19. | Hot Plug Detect |
4. | TMDS Data 1+ | 12. | TMDS Clock- | ||
5. | TMDS Data 1Shield | 13. | CEC | ||
6. | TMDS Data 1- | 14. | Reserved (N.C. on device) | ||
7. | TMDS Data 0+ | 15. | SCL | ||
8. | TMDS Data 0 Shield | 16. | SDA |
Plug and Play
Plug & Play DDC2B Feature
This monitor is equipped with VESA DDC2B capabilities according to the VESA DDC STANDARD. It allows the monitor to inform the host system of its identity and, depending on the level of DDC used, communicate additional information about its display capabilities.
The DDC2B is a bi-directional data channel based on the I2C protocol. The host can request EDID information over the DDC2B channel.
Documents / Resources
![]() |
AOC 16T20 LCD Monitor [pdf] User Manual 16T20, 16T20 LCD Monitor, LCD Monitor, Monitor |